Dell PowerVault MD3000i Manuale utente

Dell Inc Page 1

Dell PowerVault MD3000i

Configuration Guide for

VMware ESX Server Software

January 2008

Dell Virtualization Solutions Engineering

www.dell.com/vmware

Dell Inc Page 2

Table of Contents

1. Introduction................................................................................................................. 3

2. Architectural Setup ..................................................................................................... 3

3. iSCSI Connectivity Support........................................................................................ 4

4. PowerVault MD3000i Storage Setup and Configuration ........................................... 4

5. iSCSI Software Initiator Configuration on ESX Server ............................................. 5

6. Configure iSCSI storage on ESX Server.................................................................... 8

7. References................................................................................................................... 9

Dell Inc Page 3

1. Introduction

The Dell™PowerVault™MD3000i storage solution consists of a standard or high availability

configuration. The standard model has a single controller with two 1GbE ports. It can be deployed

to support up to 16 hosts non-redundantly. The high availability model has dual controllers with

two 1GbE ports per controller for a total of four 1GbE ports. The dual controller option can

connect up to 16 fully redundant hosts. This document provides instructions to setup the

MD3000i iSCSI storage solution for usage with VMware® ESX Server™software.

The Dell PowerVault MD3000i iSCSI storage array contains four Ethernet ports through which the

VD can be accessed affording both redundancy and availability of data. Provisioning of storage

on servers in a VM environment is a multiple step process starting with definition of the server

names for host access. The iSCSI connection is then established from the storage subsystem,

and after detection and configuration is established as a two way link with the associated ESX

server(s), completing the iSCSI communication subsystem. The final step allocates the detected

storage to the individual virtual machines (VM’s), where all or part of the configured storage can

be assigned to individual VM’s.

2. Architectural Setup

The following figure illustrates a typical high availability setup for using the MD3000i in an ESX

Server farm. As a best practice, Dell recommends using a separate Gigabit Ethernet network

switch to handle iSCSI storage traffic. Two servers are connected to two switches. Each switch

has a path to the MD3000i via the two dual port controllers. In this base HA configuration, the

servers, switches, and MD3000i ports share the same subnet. The NIC ports serving iSCSI

traffic on the ESX servers are teamed.

Figure 1: MD3000i High Availability Configuration

LAN

ESX Server 1

MD3000i

ESX Server 2

MD1000

Ethernet Switches

LAN

ESX Server 1

MD3000i

ESX Server 2

MD1000

Ethernet Switches

LAN

ESX Server 1

MD3000i

ESX Server 2

MD1000

Ethernet Switches

LAN

ESX Server 1

MD3000i

ESX Server 2

MD1000

Ethernet Switches

Dell Inc Page 4

3. iSCSI Connectivity Support

Operating System

Host Bus Adapter

VMware ESX Server 3.5

iSCSI software initiator with ESX Server

4. PowerVault MD3000i Storage Setup and Configuration

Create virtual disks on MD3000i using steps described in:

http://support.dell.com/support/edocs/systems/md3000i/en/IG/PDF/IGbk0HR.pdf.

After opening the Modular Disk Storage Manager and selecting the MD3000i storage array to be

configured, select the Configure tab.

Note: in the examples to follow the Storage array “sg23_training” is an MD3000i with

virtual disks already configured using the Create Virtual Disks selection. The new server

being added to an existing host group is named “Valhalla”.

From the Configure tab

1. Select Configure Host Access (Manual).

2. Enter the host name for the server which has the ESX Server software is installed.

3. Select Linux as the host type.

From the next screen, specify the iSCSI Initiator by selecting the New button (lower right on

screen). On the Enter New iSCSI Initiator screen enter a name for the iSCSI initiator name. The

label is auto-populated from the server name.

Figure 2: iSCSI Initiator Window

Host Group configuration starts from the following screen titled “Configure Host Access (Manual)

–Specify Host Group”. For ESX servers supporting VMotion, HA, and DRS, a host group must be

defined so the MD3000i storage subsystem has a configured iSCSI path to each of the hosts.

Select “Yes: This host will share access to the same virtual disks with other hosts”

If a new host group is desired select the radio button for that option and enter in a name

for your host group using standard host naming conventions (e.g. no spaces etc).

Should you already have one or more host groups assigned, select the radio button

enabling selection from a drop down list of existing host groups. This option is to be

used when configuring the second, third, etc. host in a group. Once the host group is

selected previously configured hosts for that host group will be displayed. Note that

Dell Inc Page 5

these are shown as Linux hosts even though they are configured as ESX servers.

Selecting Next provides a Confirmation screen in which the new server being configured is shown

and the other previously configured associated hosts are named. For the first server configured

in a new host group there will be no associated hosts listed under the Associated host group.

Figure 3: Modular Disk Storage Manager Configure Tab

Select Finish confirming the new host definition. This initiates the wizard configuration of the new

host.

On completion,

Select Yes to proceed to the next host you wish to configure, or

Select No to end the configuration wizard.

Helpful Hint: Record the MD3000i IP address for later configuration

5. iSCSI Software Initiator Configuration on ESX Server

This section lists the steps required to configure the software initiator on the VMware ESX Server.

Connect to the ESX server/VirtualCenter using VI Client, and follow the below steps:

1. Select Configuration->Security Profile on the ESX server.

Dell Inc Page 6

Figure 4: Security Profile Configuration Tab

2. Click on Properties. The Firewall Properties box appears.

Figure 5: Firewall Properties Window

3. Check Software iSCSI Client.

4. Select Configuration->Storage Adapters on the ESX server.

5. Select iSCSI software adapter and click on Properties.

Dell Inc Page 7

Figure 6: iSCSI software adapter under Storage Adapters on VI client

6. The iSCSI initiator Properties window appears.

7. Under the general tab select Configure tab. Select the Enabled checkbox and click OK.

Select Close.

Figure 7: iSCSI software initiator properties window

Dell Inc Page 8

8. Select iSCSI software adapter under storage. You should now see your iSCSI Target

name listed.

Figure 8: iSCSI software adapter after initial configuration

9. Select Properties under storage adapters. Select Dynamic Discovery. Select Add.

Provide the IP address of the MD3000i and click OK. There may be a slight delay before

the process completes.

Figure 9: iSCSI software initiator properties window

10. Click Close.

6. Configure iSCSI storage on ESX Server

Connect to the ESX server/Virtual Center using VI Client and follow the steps below.

1. Go to the configuration tab and select Storage Adapters. Select the iSCSI Software

Adapter and click Rescan. The newly created iSCSI target and LUN should be visible

from the ESX server.

Dell Inc Page 9

Figure 10: iSCSI target and LUNs as visible through VI client

2. Go to the configuration tab and select Storage. Click on Add Storage, select Disk/Lun

and click Next. Select the newly added storage and click Next.

3. Select the newly created iSCSI LUN and click Next.

4. Review the disk layout and click Next.

5. Provide a name for the VMFS datastore and click Next.

6. Select the appropriate block size and capacity for the VMFS datastore and click Next.

7. Review the disk layout and click Finish to create the VMFS datastore. The new datastore

is now ready to be used for storing virtual machine images.

7. References

1. Dell PowerVault MD3000i support documents:

http://support.dell.com/support/edocs/systems/md3000i/

2. Drivers download page for MD3000i:

http://support.dell.com/support/downloads/driverslist.aspx?c=us&cs=555&l=en&s=biz&Se

rviceTag=&SystemID=PWV_MD3000I&os=NAA&osl=EN

3. VMware Virtual Infrastructure 3 Documentation:

http://www.vmware.com/support/pubs/vi_pubs.html

4. Dell|VMware alliance home page: www.dell.com/vmware

Dell Inc Page 10

THIS DOCUMENT IS FOR INFORMATIONAL PURPOSES ONLY, AND MAY CONTAIN

TYPOGRAPHICAL ERRORS AND TECHNICAL INACCURACIES. THE CONTENT IS

PROVIDED AS IS, WITHOUT EXPRESS OR IMPLIED WARRANTIES OF ANY KIND.

Microsoft and Windows are registered trademarks of Microsoft Corporation. VMware is a registered

trademark and VMotion, Virtual SMP, and ESX Server are trademarks of VMware, Inc. Intel and Xeon are

registered trademarks of Intel Corp. Other trademarks and trade names may be used in this document to

refer to either the entities claiming the marks and names or their products. Dell disclaims proprietary interest

in the marks and names of others.

written permission of Dell Inc. is strictly forbidden. For more information, contact Dell. Information in this

document is subject to change without notice.

Altri manuali per PowerVault MD3000i

Indice

Altri manuali Dell Magazzinaggio

Dell

Dell PowerVault MD Series Manuale di servizio

Dell

Dell PowerVault MD3200 Series Manuale tecnico

Dell

Dell PowerVault MD3260i Series Istruzioni operative

Dell

Dell PowerVault 500 Series Manuale utente

Dell

Dell PowerVault DL2200 CommVault Manuale utente

Dell

Dell PowerVault DL4000 Guida di riferimento rapido

Dell

Dell PowerVault 110T LTO-2-L Manuale utente

Dell

Dell PowerVault TL2000 Come usare

Dell

Dell PowerVault DL2200 CommVault Manuale utente

Dell

Dell PowerVault 715N Manuale utente

Dell

Dell PowerVault Storage Area Network Manuale utente

Dell

Dell PowerVault MD3200i Series Manuale utente

Dell

Dell PowerVault MD3860f Manuale utente

Dell

Dell PowerVault MD3060e Series Istruzioni utente

Dell

Dell EMC VNXe Series Manuale del proprietario

Dell

Dell PowerVault RD1000 Manuale utente

Dell

Dell DX6000 Manuale utente

Dell

Dell Storage NX3330 Manuale utente

Dell

Dell PowerVault NX200 Manuale utente

Dell

Dell PowerVault Storage Area Network Manuale utente

Dell

Dell PowerVault MD1200 Manuale utente

Dell

Dell PowerVault TL2000 Manuale utente

Dell

Dell PowerVault MD3000i Guida

Dell

Dell PowerVault MD3000i Manuale tecnico

Manuali Magazzinaggio popolari di altre marche

QNAP

QNAP TS 32PXU Series Manuale utente

LaCie

LaCie RUGGED RAID Manuale utente

Freecom

Freecom CLS DOCK Manuale utente

PNY

PNY Attache P-FD64MBATT3 Manuale utente

HP StorageWorks MSL2024 Manuale utente

OLT

OLT 6x6 Maximizer Manuale utente

Transcend

Transcend JetFlash 160 Manuale utente

LaCie

LaCie RUGGED MINI Manuale utente

Thunderbolt

Thunderbolt 600 Manuale utente

Panasonic

Panasonic LB-DH8 series Manuale

Intel

Intel RAID High Availability Manuale utente

LaCie

LaCie 12big Thunderbolt 3 Manuale utente

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuale utente

Panasonic

Panasonic LKM-F931-1 Manuale utente

Tabernus

Tabernus Enterprise Erase E2400 Manuale utente

Rocstor

Rocstor COMMANDER 3F series Manuale utente

HP P9000 Manuale utente

Western Digital

Western Digital Ultrastar Data60 Manuale utente