Delptronics LDB-1se Manuale utente

LDB-1se Kit Instructions Page 1 of 12

Important Information

Congratulations and thank you for your purchase of the LDB-1se “Little Drummer Boy” Analog Drum Machine Kit!

Once you have built the kit, download the User Manual to learn how to use all of the features.

Before you start, please read the Electronic Kit Soldering Tutorial. It contains important and useful information even

for experienced kit builders. If this is your first electronic kit, you sure picked a big one. It is not difficult to assemble,

but there are a lot of parts. Take your time and be careful to put the right part in the right place. It is difficult to de-

solder parts if you make a mistake.

The PCB (printed circuit board) is not marked with part values, but rather with reference designators (refdes). For

example, R1 refers to resistor number one and C1 refers to capacitor number one.

The parts for the kit are in multiple bags. One or more bags contain discreet components like resistors and

capacitors, and the other bag contains electromechanical parts like jacks and switches. The discreet components are

soldered first. Before you start, separate the parts by type. When you are ready to solder parts of a particular type,

separate them by value. In general, the order that the parts are soldered onto the PCB is shortest to tallest.

The complete bill of materials is on the last two pages of this document.

Refer to the pictures of an assembled kit on pages 9 and 10 of this document.

Bottom Side Parts

The first group of parts are mounted on the bottom side of the PCB, and soldered on the top side. By top side, we

mean the side with the controls (buttons, LEDs, and potentiometer).

Diodes

There are 27 diodes. All of the diodes other than D10 are the same value (1N4148). The diodes are red and black

glass. When inserted into the PCB, the black side of the diode must line up with the stripe on the part outline on the

PCB. The diode leads need to be bent close to the body of the diode. Hold the diode body and press down on each

lead right at the body to make a U shape.

D10 is different! D10 is a BAT85 Schottky Diode. D10 goes in the upper right corner of the PCB.

D10 stands out from the rest of the diodes in the kit. Either D10 has little bits of paper on its leads, and the other 26

do not; or D10 does not, and the other 26 do.

LDB-1se Kit Instructions Page 2 of 12

Resistors

The value of a resistor is indicated by colored stripes on its body. In all cases the fifth stripe is brown (indicating 1%

tolerance), so that stripe has been omitted from the chart below.

The resistor leads need to be bent close to the body of the resistor. Hold the resistor body and press down on each

lead right at the body to make a U shape. It does not matter which lead goes in which PCB hole.

We recommend that you start with the 1K and 10K resistors because they are the most common values. Once they

have been soldered onto the PCB, it will be much easier to find the other refdes values.

Value Marking (colored stripes) Quantity Refdes

22R Red, Red, Black, Gold 2 R70, R76

220R Red, Red, Black, Black 4 R38, R46, R48, R67

390R Orange, White, Black, Black 1 R6

470R Yellow, Violet, Black, Black 2 R33, R68

560R Green, Blue, Black, Black 1 R9

820R Gray, Red, Black, Black 1 R35

1K Brown, Black, Black, Brown 12 R40, R44, R50, R61, R62, R63, R64, R65, R66, R69, R73, R75

1K5 Brown, Green, Black, Brown 1 R54

2K2 Red, Red, Black, Brown 1 R56

4K7 Yellow, Violet, Black, Brown 3 R25, R60, R74

6K8 Blue, Gray, Black, Brown 1 R57

7K5 Violet, Green, Black, Brown 1 R22

10K Brown, Black, Black, Red 10 R18, R28, R36, R41, R45, R51, R58, R59, R71, R72

15K Brown, Green, Black, Red 2 R26, R52

22K Red, Red, Black, Red 2 R7, R14

33K Orange, Orange, Black, Red 5 R13, R17, R20, R21, R31

47K Yellow, Violet, Black, Red 1 R27

68K Blue, Gray, Black, Red 2 R24, R29

82K Gray, Red, Black, Red 1 R8

100K Brown, Black, Black, Orange 9 R1, R2, R3, R4, R19, R32, R37, R42, R53

220K Red, Red, Black, Orange 3 R11, R15, R47

390K Orange, White, Black, Orange 3 R5, R12, R16

1M Brown, Black, Black, Yellow 3 R30, R34, R55

2M2 Red, Red, Black, Yellow 3 R10, R23, R39

4M7 Yellow, Violet, Black, Yellow 2 R43, R49

Chip Sockets

There are five 8-pin sockets and three 14-pin sockets. Sockets are marked with a small notch that must line up with

the outline on the PCB. Once the socket is soldered in place, the PCB outline will not be visible, so it is important that

the sockets are oriented correctly in order to ensure that the chips are inserted correctly.

Note that two of the 14-pin sockets go right next to each other to accommodate the 28-pin U6.

LDB-1se Kit Instructions Page 3 of 12

Ceramic Capacitors

Ceramic capacitors are small tan or blue blobs. Their value is marked on them with a three-digit code. The marking is

rather tiny, so you may have to use a magnifying glass to read them. It does not matter which lead goes in which

PCB hole.

We recommend that you start with the 0.1 uF capacitors because that is the most common value. Once they have

been soldered onto the PCB, it will be much easier to find the other refdes values.

Value Marking Quantity Refdes

220 pF 221 1 C24

470 pF 471 3 C14, C15, C16

0.001 uF 102 4 C8, C18, C19, C23

0.0022 uF 222 1 C20

0.0033 uF 332 2 C9, C10

0.0068 uF 682 2 C28, C29

0.022 uF 223 2 C32, C33

0.033 uF 333 6 C26, C27, C30, C31, C35, C36

0.047 uF 473 1 C11

0.1 uF 104 10 C1, C2, C3, C4, C5, C6, C7, C22, C25, C38

0.22 uF 224 1 C34

0.47 uF 474 2 C13, C21

1 uF 105 3 C12, C17, C37

Electrolytic Capacitors

There are three electrolytic capacitors. Each one is a different value, which is clearly printed on the capacitor.

Electrolytic capacitors are polarized, so which lead goes in which hole is important. The negative lead on the

capacitor is the shorter one and it is marked with a gray stripe on its body. The positive lead is longer. The positive

hole on the PCB has a square pad and is marked with a plus sign.

Value Quantity Refdes

10 uF 1 C39, C41, C42, C43

100 uF 1 C40

LDB-1se Kit Instructions Page 4 of 12

Voltage Regulators

There are two voltage regulators (refdes REG1 and REG2). They are marked KY5050 or LM7805. They have the

same basic as a transistor. It is easy to tell the difference, either by the part marking, or the fact that the two

regulators are taped together, and the nine transistors are taped together.

Make sure that the flat side of the regulators line up with the flat side of the outline on the PCB. Push the leads

through the holes, and bend the two outer leads apart to keep it in place while soldering. They will not sit flush against

the PCB, and that is fine. Do not force them.

Voltage regulators are more heat sensitive than most of the parts in this kit, so take care not to let the soldering iron

linger too long. If you are unsure, then solder one lead at a time and let the part fully cool off before soldering the next

lead.

Transistors

There are nine (9) 2N3904 transistors. They are marked on the PCB with regdes Q1 through Q9. For soldering tips,

refer to the paragraphs above relating to voltage regulators.

Power Switch

The power switch can only be inserted one way. The switch actuator faces away from the PCB. Make sure it is

seated flush against the PCB before soldering it. The switch will not stay in place by itself, so you may want to tape it

in place while you solder it. Another tip is to solder only one of the pins, then check to make sure it is flush. If it is not

flush, it is simple to reheat the one solder joint while pressing the switch into place. Once one pin is secure, the switch

will stay in place while you solder the other pins.

Power Jack

The type M power jack can only be inserted one way. The opening of the jack faces away from the PCB. Solder one

pin, then make sure it is seated flush against the PCB, then solder the other two pins.

LDB-1se Kit Instructions Page 5 of 12

3.5mm Jacks

The three 3.5mm jacks can only be inserted one way. The openings of the jacks face away from the PCB. Make sure

they are seated flush against the PCB before soldering it. They snap into place and will stay put once inserted.

¼" Jack

The one ¼" jack can only be inserted one way. The opening of the jack faces away from the PCB. Make sure it is

seated flush against the PCB before soldering it. It snaps into place and will stay put once inserted.

MIDI / DINsync Jack

The MIDI jack can only be inserted one way. The opening of the jack faces away from the PCB. Make sure it is

seated flush against the PCB before soldering it. This jack will not stay in place by itself, so you may want to tape it in

place while you solder it. Another tip is to solder only one of the pins, then check to make sure it is flush. If it is not

flush, it is simple to reheat the one solder joint while pressing the jack into place. Once one pin is secure, the jack will

stay in place while you solder the other pins.

LDB-1se Kit Instructions Page 6 of 12

Top Side Components

The pushbuttons, LEDs, and potentiometer are mounted on the top side of the PCB, the opposite side that all the

other parts are on. Refer to the photo of the completed kit for reference.

LEDs

There are 19 LEDs. They are polarized, so the direction that they are inserted into the PCB is important. The PCB

pattern has a square pad for the positive lead (anode), and is marked with a line on the negative side (cathode). The

LED has a flat side and a shorter lead to indicate the negative.

Insert each LED into the plastic LED spacer, which could be black, white, or translucent. The spacers are self-

retaining. With the spacers on, the LEDs will stay in place when you insert the leads into the circuit board, but it is still

easy enough to bump them during handling. Place and solder them one row at a time starting with the top row

(furthest from the buttons).

Make sure the LEDs are seated flush against the PCB before soldering them. If they are tilted, or are at different

heights, then the control panel will not go into place correctly. Do not bend the LED leads. That will almost ensure

that will not be flush. Solder one lead of each LED in the row. Then, double check the seating. If an LED is not quite

flush, then you need to reheat the lead while pushing down on the LED. That is far easier than heating two leads at

the same time. When the whole row is good, solder the second lead, clip the lead ends, and move on to the next row.

Pushbuttons

There are 13 pushbuttons. They snap into place and stay put while being soldered. Make sure they are seated flush

against the PCB before soldering them. Note that they are rectangular, not square, so if the pins are not lining up,

rotate the pushbutton 90 degrees.

Potentiometer

The potentiometer can only be inserted one way. It snaps in place and will stay there while you solder it. Be careful to

press down evenly so you do not bend the pins. Make sure it is all the way in and seated flush against the PCB

before soldering it.

LDB-1se Kit Instructions Page 7 of 12

Battery Snap

The battery holder wires are first threaded up through the hole next to the battery

pads, arched over, then soldered in place on top of the board. This keeps the battery

wires from getting accidentally pulled out of the PCB. The red (positive) wire goes in

the hole with the square pad, and the black (negative) wire goes in the hole with the

round pad.

Chips

There are six chips. Carefully insert each chip into its appropriate socket, making sure

not to bend any of the pins. Note the direction of the chips before inserting them. The

notch on the chip must line up with the notch on the socket. Refer to the photo of the

completed kit for reference.

The chip pins come from the factory a little bit splayed out, not pointing straight down.

You may need to bend them inward a little before you insert them. Hold the body of

the chip and rest all of the pins on one side against the table top and gently press

down just a little bit. Then do the other side. If the pins do not line up well with the

socket, repeat the straightening procedure.

Value Pins Quantity Refdes

TL072 8 2 U1, U3

TL074 14 1 U2

NoiseChip 8 1 U4 will be marked PIC12F1822 or PIC12F1571

TC1044 8 1 U5

PIC18F26K40 28 1 U6

6N138N 8 1 U7

LDB-1se Kit Instructions Page 8 of 12

Inspection

At this stage, pause to inspect your work. Compare your PCB to the photo. Make sure that:

•You didn’t forget a part.

•The chips are oriented correctly.

•All of your solder joints are good.

•There are no solder bridges (blobs of solder covering two leads/pins).

•The leads are clipped off short –right above the solder.

•The bottom side parts are seated flush against the PCB.

Test

1. Insert a new 9V battery in the battery clip and turn on the LDB-1se. The first time you turn it on, you will see the

two Row Indicator LEDs blinking alternately for about two seconds. Subsequent power on cycles will show an

animation of all of the LEDs on the unit. If you do not see the LEDs blinking, then something is wrong. Turn off

the LDB-1se, remove the battery and reinspect your work. Otherwise, go to the next step.

2. Insert a mono ¼" plug into the audio output jack and plug the other end of the cable into your amplifier or mixer.

3. The LDB-1se starts in the “Pad Play” mode. Press the buttons along the bottom of the LDB-1se to play individual

drum sounds. If you do not hear some or all of the sounds, or if an instrument sounds odd, then something is

wrong. Turn off and unplug the LDB-1se and reinspect your work.

4. If you have gotten this far, then you should be good to go. Of course, you will want to test all of the other

functions at some point to be certain that everything is soldered correctly.

5. You have successfully built an LDB-1se Analog Drum Machine. Congratulations!

Control Panel, Battery Holder, and Feet

The panel covers most of your soldering, so it is best to test the LDB-1se before putting the

panel on. First, attach the battery holder to the bottom of the panel with the two small screws

and nuts, as shown in the picture to the right.

Next, attach the plastic feet and spacers to the PCB. Then put the control panel on, and screw it

to the spacers, as shown below.

LDB-1se Kit Instructions Page 9 of 12

Bottom / Component Side of Circuit Board

LDB-1se Kit Instructions Page 10 of 12

Top / Controls Side of Circuit Board

Manuali Sintetizzatore popolari di altre marche

Kawai

Kawai MP7 Manuale tecnico

Joranalogue

Joranalogue Contour 1 Manuale utente

Full Bucket Music

Full Bucket Music Mono/Fury Manuale utente

Kawai

Kawai PH50 Manuale utente

IK Multimedia

IK Multimedia UNO Synth PRO X Manuale utente

Behringer

Behringer DEEPMIND 12 Manuale utente

Roland

Roland Gaia SH-01 Manuale utente

Roland

Roland GR-30 Manuale utente

Gotharman

Gotharman Gotharman's anAmoNo-box Manuale utente

Yamaha

Yamaha DX21 Manuale utente

QuStream

QuStream HDFS-550 Manuale utente

Modal Electronics

Modal Electronics ARGON8 Manuale utente

Roland

Roland GS-500 Manuale utente

Octave

Octave Cat SRM Manuale utente

Dreadbox

Dreadbox Murmux Initiate Manuale utente

neutral labs

neutral labs ELMYRA 2 Manuale utente

Waldorf

Waldorf KYRA Manuale utente

Tubbutec

Tubbutec Juno-66 Manuale utente