Delta Core Pack TYXAL+ Manuale utente

www.deltadore.com

Pack TYXAL+

EN Quick installation guide

- 2 -

DMB TYXAL+

CS 8000 TYXAL+

CLT 8000

TYXAL+

TL 2000

TYXAL+

Thank you for purchasing this DELTA DORE alarm pack.

This quick installation guide provides you with the basic installation instructions for your products.

Refer to the system guide for an advanced installation of your Pack.

The Pack TYXAL+ comprises:

- 1 CS 8000 TYXAL+ siren control unit

- 2 TL 2000 TYXAL+ remote controls

- 2 DMB TYXAL+ motion detectors

- 1 CLT 8000 TYXAL+ touch screen keypad

Siren control unit

The control unit is the heart of the system

and manages all the information ex-

changed between products.

It sets off the indoor siren in the event of an

alarm.

4-button remote controls

These enable the system to be activated or

deactivated totally or by zone.

Two buttons (1 and 2) can be conﬁgured for

control of the alarm by zone, the triggering

of a discreet or audible emergency alarm

or control of control systems (e.g. garage

door).

Touch screen keypad

It is an essential component and is used for

all the control actions of the installation.

With its access code, it enables the system

to be activated or deactivated totally or by

zone. Wall-mounted, it informs you of the

system's status.

It reads the last events occurring, shows

the indoor (measured by the keypad) and

outdoor temperature (if an outdoor siren

is associated with the control unit) and is

used to personalise the system.

Motion detectors

Wall-mounted, they detect any person

moving in the room where they are

installed and report this to the control unit.

The "standard" lens can be replaced with

an "animal" lens (supplied with the

product).

R&TTE 1999/5/CE

- 3 -

Activation: main steps

Installing and mounting the products

starting with:

- the CS 8000 TYXAL+ siren control unit

- the CLT 8000 TYXAL+ touch screen keypad

- the DMB TYXAL+ motion detectors

The TL 2000 TYXAL+ remote controls can be programmed (functions of buttons 1 and 2) and associated with the

control of control systems

Adding additional products (if necessary)

Products that are not part of the Pack TYXAL+ must be associated with the system:

- intruder detectors and technical detectors,

- keypad, badge reader, remote controls, etc.,

- indoor or outdoor siren, telephone transmitter, etc.,

To do this, refer to the "Adding products" chapter of the system guide.

Personalising the installation and products (see system guide).

- Naming the products

- Managing the operating zones

- Creating installer and user access codes. We strongly recommend that you create your own code (123456 on

activation).

- Adjusting advanced settings...

For more detailed explanations, refer to the system guide.

Testing the installation

Overview of your installation

Close the alarm control unit

The products in the Pack TYXAL+ were associated in the factory

so as to make them easier to install.

- 4 -- 4 -

Installing and mounting the products

1.1 CS 8000 TYXAL+ control unit

• Location

- On a ﬂat surface, with enough space all around for installation

and opening the battery cover.

- In the centre of the system and ﬁtted in a high position to obtain

the best radio link (avoid basements).

- In an open area to obtain the best dispersion of sound for the

integrated siren.

- In a place difﬁcult to locate by an intruder but easily accessed by

the user.

- In an area protected by an infrared motion detector.

- At least 2 metres away from any other wireless transmitter

• Mounting

ÊSeparate the parts

ËFit the mounting bracket

ÌConnect the battery unit

Lithium battery

BATTERY UNIT 2x3.6V

LSH 20

Remove protective tab Unscrew Separate the base from the rest of the si-

ren by pushing up and pulling toward you.

Separate the con-

trol unit from the

base.

Incorrect Correct

Mark and drill holes

(A, B, C and D)

Fit the mount (screws A and B) to

the wall (do not ﬁt screws C and D

at this point).

Fit the base back on to the mounting bracket

and secure it with the screws (C and D).

= Tamper alarm on opening. Important: do not damage this part of the

support (required for the tamper alarm). Screw back with care.

- 5 -- 5 -

1.2 CLT 8000 TYXAL+ touch screen

keypad

• Location

It is advisable to install the touch screen keypad inside near one

of the main entrances, if possible protected by an intrusion

detector (e.g. DMB TYXAL+)

The user must have easy access and it can be mounted on a wall

at a height of 1.50 m.

Avoid proximity with metal surfaces or an electrical switchboard.

Important: if the touch screen keypad is protected by a detector

(door/window or motion), you must use a delayed triggering for

the detector when activating it.

• Mounting

Ê Separate the 2

parts of the unit.

Ë Mark and drill holes D1, D2 and D3.

Mount the base using screws V1, V2 and V3.

!Do not damage or lose the rubber part C

(required for the tamper alarm).

HAUT

12 3

D3D2

Lithium battery

3 x LS 14500 3,6 V

~1,50 m

Ø max = 3 mm

Ê Fit the battery unit, observing the right

polarity.

Close and lock the unit.

- 6 -

Installing and mounting the products

1.3 DMB TYXAL+ motion detector

DMB TYXAL+ uses infrared (heat) to detect any moving presence in the room.

It has 2 removable lenses:

- no. 1: standard (ﬁtted on the product supplied).

- no. 2: animal immunity (does not detect animals of a certain size,

or household appliances such as robot vacuum cleaners).

• Location

The motion detector must preferably be placed in a corner:

- prevent any source of heat or motion of a hot body

nearby (convector, ﬁreplace, ...),

- the ﬁeld of detection must be clear of any obstacles (curtain, cupboard, etc.),

- the detector must not be pointing at an opening to the outside (window),

- you can cross the beams of 2 detectors,

- the detector must be installed between 2.20 m and 2.40 m from the ﬂoor.

For a greater height, use a RO DMB ball joint

(unless with the animal immunity lens).

• Field of detection/Restrictions

The ﬁelds of detection below are given for a temperature of 19°C and person of average body size.

• Animal immunity

Zone not authorised for animals

Zone authorised for animals ≤than 10 kg

Zone authorised for animals (see details A1, A2, A3)

If there are several animals, add their weights together.

Example 1: a French bulldog weighing 15 kg and 25 cm tall is in zone A1. It is a short coated dog, and will not be detected.

Example 2: a Doberman weighing 30 kg and 50 cm tall is in zone A2. It is short coated dog, and will be detected.

No.2

10 m8 m6 m4 m2 m0 m

0,6 m

1,6 m

2,3 m

≤ 10 Kg

30 kg20 kg10 kg0 kg

0 cm

10 cm

20 cm

30 cm

40 cm

50 cm

60 cm

40 kg 50 kg

A2 A3 A1 A2 A3

Long coated ✔✔✔

Medium coated

✔ ✔ -

Short coated ✔--

Fur authorised zone A

1 m mini

Side view

0,5m 4 m 7 m 12 m

2,30m

12m10m8m6m4m2m0m

90°

Side view

Top view Top view

2m 4 m 7 m 10 m

2,30m

10 m8 m6 m4 m2 m0 m

0 m

2 m

4 m

6 m

2 m

4 m

6 m

90°

No.1 No.2

- 7 -

• Mounting

- Open the unit

- Mark and drill the holes according to the location

of the detector (see below A, B, Cor D)

- Mount it on the wall

• Change the lens

Example: you want to replace the standard lens by the "animal"

lens.

Push the stops to lift off and remove the lens.

Fit the new lens.

Be careful not to touch the sensor.

• Activation

Insert the battery, observing the right polarity.

Check that the rubber part is present before closing up the

detector.

n°1 n°2

Lithium Battery - AA

LS 17500 - 3.6 V

2,20 2,50 m

✔

> 2,50 m

RO DMB

✔

Do not use ball joint RO DMB

(P/N: 6416221) with the animal

immunity lens.

V10

ABCD

Ø max = 3 mm

V3,V7,V8 = Tamper alarm on opening.

Important: do not damage or lose the rubber part (required for

the tamper alarm).

123

- 8 -

Installing and mounting the products

1.4 Conﬁguring a TL 2000 TYXAL+

remote control

Buttons 1 and 2 can be programmed separately.

You can therefore mix the functions.

Examples:

(1Mode A ,2Mode C );

(1Mode D ,2Mode E );

(1Mode A ,2Mode D )...

Ask your installer for the appropriate equipment if you want

openings to be controlled.

Conﬁguring buttons 1 and 2

1 2

Mode A

Mode B

Mode C

Mode E

Mode D

> 5s

123

1 2

... ... ...

... ...

Ê Press the

1and 2buttons simultaneously for

5 seconds until the LED changes to

orange.

Ë Press the 1or 2button.

The LED ﬂashes.

Then, press the 1or 2button brieﬂy as many

times as necessary, select the required operating

mode to apply: Mode A: 1 ﬂash, Mode B:

2 ﬂashes, ..., Mode E: 5 ﬂashes.

Ì Press the ON button

to conﬁrm.

The LED changes to

green.

Activa-

tion

Button 1

programmable

Button 2

programmable

LED

Deactivation

the alarm

You can activate or deactivate the alarm system with the

remote control.

Depending on the conﬁguration deﬁned with your installer,

buttons 1 and 2 can be programmed and have

different functions (see table opposite).

Button 1Button 2

Mode A

Alarm control by zone

ON/OFF zone 1

(e.g. Floor)

ON/OFF zone 2

(e.g. Ground ﬂoor)

Mode B

Triggering of an emergency

alarm with siren

SOS

Transmitter

without audible signalling

Mode C

Triggering of an emergency

alarm with siren

SOS

Transmitter call + audible alert

Mode D

Pulse control of a control

system or lighting x1

Mode E ON/OFF

ON/OFF control for lighting or

roller shutters

- 9 -

Adding additional products (if necessary)

Example: a telephone transmitter

ËEnter the installer code (123456, by default) and conﬁrm with OK.

ËPress Settings, select the menu:

Installation > Products, then conﬁrm with OK.

The alarm control unit's red LED switches on.

ÌSelect "Add", then conﬁrm with OK.

ÍBrieﬂy press the (T1) button on the front panel of the

transmitter.

The transmitter emits a beep when the button is pressed, then a

second beep to conﬁrm the association.

The alarm control unit emits a beep.

Maintenance

mode

Download

Programming

Access codes

Software version

Settings

Clock

Languages

Return

Installation Installation

Zones

Door chime

Test

Initialisation

Products

Return

Add

product

Press the button of the

Return

Products

Delete

Activate/deactivate

Configure

Return

Add

Access code

XXXXXX

SOS

TYXAL TTRTC

RTC 0 03 01

Configure

Added

Return

25/11/14 12:48

SOS Settings

OFF

Enter your code

Info

Settings

My home

OFF

25/11/14 12:48

Close the alarm control unit

1 2

Ê Replace the cover of the siren Ë Screw in the closing screw

and replace the protective tab

- 10 -

Personalising the installation and the products

The CLT 8000 TYXAL+ touch screen keypad allows all the personalisation operations of the system.

The following menus can be accessed by the installer code.

The CLT 8000 TYXAL+ touch screen keypad can be used for all activation actions.

Deactivate the tamper alarm (see § Deactivating the tamper alarm, system guide) and separate it

from its wall mount.

Example: DMB TYXAL+ motion detector

• Name the products

ÊEnter the installer code (123456, by default) and conﬁrm with OK.

ËPress Settings, select the menu:

Installation > Products > Conﬁgure, then conﬁrm with OK.

ÌPress the button of the product to rename or select it

from the list of products by clicking on "Browse"

(see table below), then conﬁrm with OK.

ÍOnce the product is identiﬁed, select the

"Name" menu, then conﬁrm with OK.

ÎYou can choose a name from the list

(recommended), then a number (optional)

or personalise (Ï) the product name by entering a new name.

Conﬁrm with OK.

• Entry timer on intrusion detectors (immediate/delayed triggering)

ÊEnter the installer code (123456, by default) and conﬁrm with OK.

ËPress Settings, select the menu:

Installation > Products > Conﬁgure, then conﬁrm with OK.

ÌPress the button of the product to change or select it

from the list of products by clicking on "Browse",

then conﬁrm with OK.

ÍOnce the product is identiﬁed, select the "Entry timer" menu, then conﬁrm with OK.

ÎSelect the type of triggering:

immediate or delayed (5 to 45 seconds), then conﬁrm with OK.

Immediate: if a presence is detected, the alarm is immediately

triggered.

Delayed: if a presence is detected, the alarm is triggered after a

delay (set from 5 to 45 seconds) to give the user time to deac-

tivate the alarm, after entering the building (e.g. activation or

deactivation with a wall-mounted touch screen keypad).

During this time, the alarm control unit emits warning beeps.

abc def

jkl

ghi mno

tuv

pqrs wxyz

25/11/15 12:48

SOS Réglages

OFF

Entrance timer

Immediate >

Return

DMB 0 AD AD

Return

Tamper alarm

Name

Entrance timer Entrance timer

< 5 s >

Return

Entrance timer

< 45 s >

Return

Installation

Zones

Door chime Ok

Products

Return

Name

Bedroom

Child's bedrm

Master bedrm

Return

Configure

Browse

Return

product

Press the button of the

Products

Activate/deactivate

Return

Add

Configure

PSTN transmitter

Return

Tamper alarm

Entrance timer

Name

Settings

Clock

Languages

Return

Installation

Access code

XXXXXX

SOS

or Browse

Configure

Return

CLT 0 54 22

DMB 0 AD AD

RTC 0 03 01

Number

Return

25/11/14 12:48

SOS Settings

OFF

Enter your code

Info Settings

My home

OFF

25/11/14 12:48

Indice

Manuali Sistema di sicurezza popolari di altre marche

Inner Range

Inner Range Concept 2000 Manuale utente

Climax

Climax Mobile Lite R32 Istruzioni per il montaggio

CADDX

CADDX NX-6 Manuale utente

FBII

FBII XL-31 Series Manuale utente

Johnson Controls

Johnson Controls PENN Connected PC10 Manuale utente

Aeotec

Aeotec Siren Gen5 Manuale utente

Blaupunkt

Blaupunkt SA 2700 Manuale utente

IDEAL

IDEAL Accenta Manuale del proprietario

AJAX

AJAX DoubleButton Manuale utente

Swann

Swann SW-P-MC2 Manuale utente

Ecolink

Ecolink Siren+Chime Manuale utente

Digital Monitoring Products

Digital Monitoring Products XR150 Manuale utente

EDM

EDM Solution 6+6 Wireless-AE Manuale utente

Highway Safety Group

Highway Safety Group EA401 Manuale utente

Siren

Siren LED GSM Manuale utente

Detection Systems

Detection Systems 7090i Istruzioni per il montaggio

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuale utente

Siemens

Siemens FDM273 Manuale utente