DELTA DORE TYXIA 631 Manuale utente
EN Pack for control of blackout blind, awning and
indoor venitian blinds
PACK TYXIA 631
EN
32
1/ Remote control installation............................. 4
1.1 Mounted on the wall ................................. 4
1.2 Placed on a at surface ............................ 4
2/ Installing the receiver ........................................ 5
2.1 Connection instructions
for terminals 1 2 3 4. ........................................... 7
2.2 Connection instructions for
IN1 - COM - IN2 terminals ............................. 8
2.3 Connection ................................................... 9
3/ Wireless association........................................ 10
3.1 Associating a receiver or motor........ 10
3.2 Associate multiple receivers
or motors ............................................................... 13
4/ Conguring the receiver................................ 15
5/ Learning for the shutter travel time......... 16
6/ Learning for the tilt time................................ 17
7/ Save the favourite positions......................... 18
8/ Use ........................................................................... 19
9/ Troubleshooting................................................. 20
10/ Technical characteristics............................. 22
Contents
EN
54
1/ Remote control installation 2/ Installing the receiver
Recommendations
IMPORTANT: the control wires are not insulated
from the mains power supply. All connected equip-
ment must be marked CE and meet the require-
ments of the low voltage devices as well as assembly
recommendations. Local control wires can be
extended up to 10 m
(separate from the 230 V).
The roller shutter high and low stops must be set
before the receiver is installed.
1.1 Mounted on the wall
1.2 Placed on a flat surface
Use an electrically
isolated tool to
perform the actions
on the receiver con-
guration button.
10A circuit breaker
required.
10 A
EN
76
You can install the receiver for roller shutter in
a ush-mounted box behind a switch or control
push-button or in a sealed box inside the roller
shutter, a safe distance from metal parts.
Switch off the installation
power supply
230V~
OFF
2/ Installing the receiver
2.1 Connection instructions
for terminals 1 2 3 4.
Strip the wires while respecting
the strip length speci ed on the product.
Removal recommendations
- Switch off the power supply.
- Use the tool supplied or a
2.5 mm screwdriver to press
the button of the front terminal
before removing the wire.
123 4
1
2
IPx4
2
1
• Stranded wires
Using the tool supplied or a
2.5 mm screwdriver, press the
terminal button then insert the
wire.
• Solid wires
Push the wire fully
into the terminal.
0,75 - 1,5 mm
Ø
2
EN
98
2/ Installing the receiver
2.2 Connection instructions for
IN1 - COM - IN2 terminals
- Use the wires supplied.
- Push the wire fully into the
terminal.
Do not strip the wires when they are
connected to the product as you could
damage the internal connector.
2
7mm 0,5 mm
KY31A02
123 4
Removal recommendations
Turn the wire while pulling
on it. 1
2
123 4
2.3 Connection
- Connect the motor control wires to terminals 3
and 4 (motor lowering control wire to terminal 3,
raising control wire to terminal 4).
- Connect the switch to the IN1 - COM - IN2
terminals.
- Connect the 230 V power supply to terminals 1
and 2.
- Switch the installation power back on to continue
with the association operation.
230 V~
IN1
COM
IN2
1 2 3 4
TYXIA
1 2 3 4
IN1
COM
IN2
IN1
COM
IN2
IN1
COM
1
2
3
1
2
1
2
Hold switch
Double
push-button
Push button
EN
1110
❷On the remote control press and at the
same time and hold for 3 seconds, until the red
LED ashes. Release.
If a receiver is found, the LED will light up
green brie y.
❸After a few seconds, the shutter will activate
twice to con rm the association.
The LED stops ashing.
The association mode is automatically exited.
1 2 3 4 1 2 3 4
... ... ...
> 3s
1 2 3 4
TYXIA TYXIA
> 3s
3/ Wireless association
This chapter allows you to associate a remote
control with an X3D wireless motor or X3D roller
shutter receiver.
You can associate up to 16 receivers (or motors).
3.1 Associating a receiver or motor
3.1.1 A single receiver is turned on
❶Press and hold the receiver button for 3 seconds
until the LED ashes, release.
EN
1312
3/ Wireless association
3.1.2 Several receivers or motors are in association
standby mode
❶On the remote control press and at the
same time and hold for 3 seconds, until the red
LED ashes. Release.
The remote control searches the different receivers or
motors.
The LED ashes red, then briey green as soon as a
new receiver is found.
❷When the LED starts ashing red slowly, press
the button as many times as required to select
the receiver to associate.
The corresponding shutter activates briey.
❸Once the receiver has been found, press .
❹After a few seconds,, the shutter will be
activated twice to conrm the association.
To exit association mode, press for 3 seconds.
3.2 Associate multiple receivers
or motors
❶Set the receivers to association standby mode.
❷On the remote control press and at the
same time and hold for 3 seconds, until the LED
ashes. Release.
The remote control searches the different receivers or
motors.
The LED ashes red, then briey green as soon as a
new receiver is found.
❸ When the LED starts ashing red slowly, press
and at the same time and hold for 3
seconds until the red LED turns on.
❹ The shutters are activated briey to conrm the
association.
EN
1514
4/ Con guring the receiver
Congure the receiver according to the type of
switch connected.
Mode 1: Hold switch
Raise/Stop/Lower
Mode 2 (by default):
Raise/Lower double push-button
Raise + Lower: Stop
Mode 3: Raise/Stop/Lower/Stop
push-button
IN1
COM
IN2
IN1
COM
IN2
IN1
COM
1
2
3
1
2
1
2
To modify the receiver configuration
❶Press the receiver’s button for 6 seconds.
❷The LED ashes, then becomes steady, release.
The number of ashes corresponds to the current
mode.
❸
Brie y press the receiver button to select the
mode
.
❹ Con rm the selected mode by pressing the
button for 3 seconds until the LED switches off.
1 2 3 4
TYXIA
1 2 3 4
TYXIA
1 2 3 4
TYXIA
Mode 1 Mode 2 Mode 3
EN
1716
6/ Learning for the tilt time
Do not carry out this operation, if the
TYXIA 5731 controls an awning.
❶Hold down the receiver button for 9 seconds,
the LED switches off, then release. The shutter is
positioned at the
midpoint of its
height
❷Press and hold
the rotation button
(step by step
mode) until the
shutter has rotated
fully, then press
stop.
❸The tilt time is
recorded.
5/ Learning for the shutter travel time
Perform a complete cycle from stop to stop:
❶ Lower or raise the roller shutter completely to
the stop.
❷Do the reverse action until the opposite stop is
reached.
Note: The learning for the shutter travel time
adjusts itself automatically for each complete cycle
from stop to stop.
Do not interrupt the roller shutter travel.
50%
TYXIA
>9s
EN
1918
8/ Use7/ Save the favourite positions
You can save up to 2 favourite positions: and
.
❶❷ Set the shutter to the required position
(e.g. ).
❸Press or to set the angle of the slats.
❹Press + or + and hold for 3
seconds to save the position. The red then green
LED indicates that the receiver has correctly received
the information. The shutter is activated brie y.
Release.
> 3s
• Press , or to control the roller shutter.
The red then green LED indicates that the receiver has
correctly received the information.
• Press or to set the angle of the slats.
• Press to go to favourite position 1 (if it has
been saved).
• Press to go to favourite position 2 (if it has
been saved).
Altri manuali per TYXIA 631
2
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali DELTA DORE Controllori
