Dension Wi-Drive Manuale utente
Dension Wi-Drive
Dension Wi-Drive creates a WiFi hotspot using the internet connection of a 3G
USB modem.
Dension Wi-Drive User's Manual v .0
Quick start
If you are an advanced user, you can set up your Wi-Drive following these 6
steps:
. Power up Wi-Drive with the 3G modem connected to the lower connector of
the double USB port
2. Connect to the WiFi network “Dension Wi-Drive”
3. Go to the administration page at the address “www.wi-drive”
4. Enter the default administration password: “admin”
5. Set up your internet and WiFi preferences
6. Save the settings and reconnect to the WiDrive
1 Setup
Once Wi-Drive is installed in your car, you can begin with setting up its internet
connection settings and adjust WiFi parameters.
You will need to be in the WiFi range of Wi-Drive and it needs to be powered on
(the MOD light should flash slowly in green colour).
. Using the WiFi connection
manager of your computer,
connect to the WiFi network
“Dension Wi-Drive”
2. Open a web browser (e.g.
Internet Explorer) on your
computer and enter the address
“www.widrive” to get to the
administration page of the device.
Enter the default administration
password “admin” and click the
Login button.
3. You are now on the settings page
of your Wi-Drive, where you can
set up your internet connection
and WiFi preferences.
Please consult the description of
each setting in the table below,
and set them accordingly.
After you are finished, click the
Save button.
If you have altered the WiFi
preferences (Netowrk name,
Security, or Passphrase), you
need to re-connect your computer
to the new WiFi network.
. Settings
Section Setting Description
GSM Preferences
PIN code If the SIM card inserted in your 3G modem
requires a PIN code, enter it here
Country Select the country where your mobile
network operator is in
Provider Select your provider from the list, and if
available also your data subscription plan
(e.g. pre-paid, contract, etc.)
Advanced
Settings
You only need to set this if
•Your provider is not listed in the above
selection
•You use a non-standard data
subscription with custom settings
•You have trouble connecting to the
internet through Wi-Drive
In the above cases, please contact your
mobile network operator and ask for these
settings (APN, username, password, DNS
servers, gateway).
nable
roaming
Check this box if you also want Wi-Drive to
connect to foreign networks.
Beware of high data roaming costs.
nable on-
demand
connection
Check this box if you want Wi-Drive to only
connect to the internet when there is an
actual request from a connected computer.
This is useful for time-limited data
subscriptions.
Wi-Fi Preferences
SSID The WiFi network name with which Wi-Drive
will appear to other WiFi devices
Security You can select between
•Open network:
In this mode, anyone will be able to
connect to Wi-Drive without a
password.
•WPA2 Pre-Shared key:
Clients will be required to enter the
passphrase (password) that you set up
Passphrase The password used to connect to Wi-Drive in
WPA2 mode.
Web Interface
Preferences
Password,
Confirm
password
The password for the administration page
you are at. With this, you can prevent users
from changing your settings.
1.2 “About” page
The “About” tab on the administration web page contains information about your
Wi-Drive device, like its serial number and software version.
Should you need to contact Technical Support, please include this information in
your request.
The page also informs you about your internet connection status.
2L Ds and Buttons
2.1 LED flashes and their meaning
Wi-Drive indicates its status via the dual-color LED with the label “MOD”.
Red Green State
Very slow - Standby
Fast Fast Powering up
- Solid Initializing
- Slow Ready, no 3G connection
Fast Fast Ready, 3G connection
established
Slow - Software upgrade in
progress
2.2 Push button
The push button on the front left side of the device allows two advanced
functions:
Length Function Usage
Two short presses System reset Use this function if Wi-Drive
becomes unresponsive in any state
Very long press
(> 5 secs)
Restore factory defaults If you forgot the administration
password, or you want to restart
configuration from the default
settings.
3 Operation
If your Wi-Drive is installed and fully set up, it will power up when the ignition of
the car is on.
After powering up, it will connect to the internet and you can start using the WiFi
hotspot.
When the ignition of the car goes off, Wi-Drive will power down, and stay in a
low-power standby mode.
4 Troubleshooting
In case Wi-Drive does not work as expected, check the followings:
Problem Resolution
Cannot connect to
Wi-Drive over
Wi-Fi
•Check whether Wi-Drive is powered on
•Check the network settings on your computer
•Make sure you did try to connect to Wi-Drives WiFi
network and use the correct password
•Perform a system reset via the push button
•Restore the factory default settings
Cannot connect to
the internet via
Wi-Drive
•Ensure that the 3G modem is inserted firmly into the
USB connector
•Ensure that your GSM Preferences are set up
correctly (contact your network operator if
necessary)
•Check whether Wi-Drive could establish an internet
connection (on the About tab of the administration
page)
•Try to connect to the internet with your 3G modem
on a computer to see if it works
5 Firmware Upgrade
The operating system of Wi-Drive (firmware) can be upgraded via connecting
a USB disk to one of the USB ports.
For detailed instructions, consult the Release Notes that came with your firmware
upgrade package.
6 Default settings
WiFi network name (SSID) “Dension Wi-Drive”
(open network)
Administration page www.widrive ( 92. 68. 00. )
Administration password “admin”
7 Technical specifications
Operating Voltage 0.7 - 6V
Active Current max. 400mA + 3G modem use (~400mA) @ 2V
Standby Current 00 uA
Maximum USB supply .5 Amp @ 5V
Operating temperature -20 ~ +60 C
WiFi operating distance ~ 0 meters w/o antenna, ~30 meters with antenna
Coverage depends on installation and environment
WiFi maximum users 6
8 Installation
8.1 Wi-Drive connectors
All non-described ports, connectors and switches are not used, and should remain
unconnected.
Wi-Drive can be installed in two ways:
8.2 Plug & Play
For a plug and play connection follow these steps:
. Connect the cigarette lighter cable to the power connector of Wi-Drive
2. Connect the USB 3G modem to the lower connector of the double USB port
3. Connect the cigarette lighter adapter to the socket in your car
4. Follow the Setup guide in chapter
Note:
For a plug and play installation, connecting a WiFi antenna is not necessary.
Wi-Drive will still be able to operate within a 0 meter range.
WiFi antenna port Power
connector
Push
button
Status
LED
USB port
for 3G
modem
8.3 Fixed installation
If you want to have a fixed installation, with Wi-Drive possibly hidden, follow
these steps:
. Connect the wire power wire harness to the cars electrical system.
The red wire needs to be connected to constant + 2V with a supply of
Amps at least.
2. Connect the USB 3G modem to the lower connector of the double USB port
3. Connect the power wire harness connector to Wi-Drive
4. Follow the Setup guide in chapter
Hint: You can increase 3G reception quality if you place the 3G modem near to a
window, or other non-covered area. Use a good quality standard USB extension
cable.
Indice
Altri manuali Dension Router wireless
