DESi Utopic 2 Manuale utente
Wireless Motorized Cylinder
With Remote Controller
USER
MANUAL
URC 60
1. GENERAL INFORMATIONS and WARNINGS
- We recommend you to put the keys to an accessible place (like car, bag etc.) in an
emergancy condition.
- If there is any problem with door or locking mechanism, first of all, those problems need to
be solved. Door's mechanical parts and locking mechanism should be working properly.
- If there is a problem with the device, first look to the troubleshooting part of this manual. If
you cannot solve the problem, contact with your dealer.
- Replace the batteries, if there is a battery warning. RECYCLE EMPTY BATTERIES!
- All the system need to be protected from water, direct sunlight and shocks.
- Place the batteries after installation of the system to the door. If the batteries are placed
before the installation, auto-rotating parts may cause injuries. WATCH YOUR FINGERS!
!
We would like to thank you for choosing this patented product. We hope you to enjoy it.
DES Alarm and Securty System Inc.
3
1.1. FEATURES OF THE DEVICE
Structure
Engraved block alluminum
Cylinder Length
(outside) 26 mm | 10 mm | 34 mm (inside)
Inside part can extensile up to 40 mm with extending parts.
(Different cylinder lengths are available)
Batteries and Battery Life
5x 1,5 V AA size Alkaline or Lithium batteries.
Device is suitable to use with rechargable batteries.
According to tests done in DESi labratories, battery life of the
device is measured as follows:
3 years standby or
10.000 operations (locking or unlocking) for 3 rotation locks
Remote Controller
434 Mhz Anti-duplicatiion rolling code remote controller with
action display
Remote Controller (wireless device) Memorry
Motorized cylinder can learn up to 40 remote controllers.
Controlling Options and Compatible Accessories
Wireless Fingerprint Reader
Wireless Keypad
Bluetooth Interface
Wireless Auto-Locking Module
Wireless Home Automation Interface
Wireless Secretary Button
Remote Access Module
1.2. BOX CONTENT (may vary according to model number)
1x Wireless Motorized Cylinder (with keys)
1x Master Remote Controller
2x User Remote Controller
1x Installation screw and Hex key
User Manual
42. PARTS OF REMOTE CONTROLLED MOTORIZED CYLINDER and INSTALLATION
Cylinder
Handle
Handle Screw
Hex Screw
The hole
for hex key
DEMOUNTING OF MOTOR AND CYLINDER
- Open “handle screw” and remove the handle by pulling.
- Remove the batteries.
- Rotate “hex screw” to counter-clock wise by using the
hex key out of the box. You will see the cylinder will be
disassembled from the motorized part.
To assemble two parts, combine cylinder and motorized
part in a proper way and rotate hex screw to clock wise.
Metal Extending Parts
(used if needed)
Plastic Cover Cover Spring
5
Master RC
Full-Turn Locking
In the administrator menu;
Shift to next menu item or Confirm
Unlock and Open
In the administrator menu;
Shift to previous menu item
1 Turn Locking
To enter administrator menu,
press 3 seconds.
In the administrator menu;
Enter to displayed menu item.
Display
2
1
3
Full-Turn Locking
1 Turn Locking
Unlock and Open
Display
User RC
Up to 6 mm
EXTENDING INSIDE PART OF THE CYLINDER (if needed)
If the door thickness is not suitable to the cylinder of the device, inside part of the
cylinder may be extended up to 6 mm by 2 mm steps.
To extend the cylinder’s inside part, follow the instructions below:
- Open “handle screw” and remove the handle by pulling.
- Remove the batteries.
- Rotate “hex screw” to counter-clock wise by using the hex key out of the box till the
motorized part is disassembled from the cylinder.
- Add 2 mm metal extending parts as needed.
- Assemble cylinder and motorized part and rotate hex screw to clock wise direction.
- Install the batteries and check the device if it is working properly or not.
26 10 34
26 10 40
62.1. INSTALLATION OF MOTORIZED CYLINDER
2.1.1. Installing The Device Without Plastic Cover (Recommended for ordinary people)
This is the easiest installation. It is suitable for all kind of doors.
In some security doors, even if you remove cylinder screw, you cannot remove cylinder due to cramped installation of cylinder
defender. Follow the instructions below, for that kind of situations: (Recommended for professional installers.)
- Untighten screws of cylinder defender (don’t remove the screws)
- Remove cylinder screw and take out the old cylinder.
- Disassemble the motozied cylinder in to two parts as it is mentioned on page 4.
- Install the cylinder part to the door and tighten the cylinder screw.
- Tighten the screws of cylinder defender.
- Assemble the motorized part with cylinder as it is mentioned on page 4.
1.STEP
Remove
existing
cylinder.
2. STEP
Install
motorized
cylinder and
tighten
the screw
That’s
it!
Old Cylinder Cover Motorized Cylinder
7
2.1.2. Installing The Device With Plastic Cover (For professional installers only)
If the cover of the door is not a part of cylinder defender (if it is used just to cover the disturbancies around the cylinder hole)
follow the instructions below to install the device:
If the cover of the door is used to install the defender, follow the instructions below to install the device:
- Remove the old cylinder.
- Remove cover of the door, the metal holder of cover and the defender.
- Adjust the screw lengths according to the new distance between defender and the cover of the door when the metal holder is
not used. (There are two adjustable screws in the box)
- Install cover of the door and defender with new screws adjusted in previous step.
- Install the motorized cylinder with cover spring and plastic cover.
(Please look to the next page for related illustrations.)
1.STEP
Remove
the cylinder
and cover
of the door.
2. STEP
Install the
motorized
cylinder with
cover spring
and
cover.
Old Cylinder Cover of the door Motorized Cylinder
That‘s
it!
Spring Cover of the device
8
Old Cylinder Metal
Holder
Cover
of the Door
Cover of The Door Motorized
Cylinder Cover
Spring
Defender
Screws Defender
(outside)
Adjusted
screws Defender
(outside)
Plastic Cover
1.STEP
Remove
the old
cylinder.
2.STEP
Remove the cover
of the door,
metal
holder of
cover and
defender.
3.STEP
Adjust the length
of two screws
out of
the box.
4.STEP
Install the cover
of the door
with adjusted
screws without
using metal
holder.
5.STEP
Install
the motorized
cylinder with
cover spring
and cover.
That’s
it!
i
This installation is recommended for porfessional installer only, due to needed technical knowladge about door and lock.
Cover
of The Door
9
3. ADMINISTRATIVE ACTIONS / SETTINGS
3.1. ENROLLING NEW REMOTE CONTROLLER
- Press 3rd button of master rc till “0" flashes on the display.
- Press 2nd button of master rc three times. “6" will be flashing on the display.
- Press 3rd button of master rc. “L” will be appeared on the display.
- Press 1st button of master rc. The cylinder will give a long (5 sec) and a short warning tone one after the other.
- Just after short warning tone, press 1st button of new remote controller
till you hear 2 warning tones from the cylinder.
In this way, the new remote controller will be enrolled to the device. Schematic representation of operation is as follows:
Master RC
3.2. DELETING ALL THE REMOTE CONTROLLERS
- Press 3rd button of master rc till “0" flashes on the display.
- Press 2nd button of master rc two times. “7" will be flashing on the display.
- Press 3rd button of master rc. “d” will be shown on the display.
- Press 1st button of master rc. The motorized cylinder will give a long (10 sec) and two short warning tone one after the other.
In this way, all the remote controllers (except the master rc) would be deleted from the device.
Schematic representation of operation is as follows:
3s 3X 5s Bp Bp Bp Bp
3s 2X 10s Bp Bp Bp
Before using your motorized cylinder, Direction of locking/unlocking (p.10) and Number of turns (p.10) should be adjusted.
i
10
Master RC
3.3. ADJUSTING THE DIRECTION OF LOCKING / UNLOCKING
- Press 3rd button of master rc till “0" flashes on the display.
- Press 1st button of master rc one time. “1" will be flashing on the display.
- Press 3rd button of master rc. Either “r” or “L” will be shown on the display.
- For counter-clockwise locking, choose “L” by pressing 1st button, for clockwise locking, choose “r” by pressing
2nd button and than press 3rd button to confirm selection. Three lines will be shown on the display.
After first locking or unlocking operation done by master rc, selected settings will be applied to the system.
Schematic representation of operation is as follows:
3.4. ADJUSTING THE NUMBER OF TURNS
- Close the door and press 3rd button of master rc till “0" flashes on the display.
- Press 1st button of master rc two times. “2" will be flashing on the display.
- Press 3rd button of master rc. “o” will be shown on the display.
- Press 1st button of master rc. The motorized cylinder will give a long (3 sec) warning tone and it will lock and unlock the door.
In this way, motorized cylinder learns the number of turns of the locking mechanism.
Schematic representation of operation is as follows:
3s
3s 2X 3s Bp Lock and Unlock
Altri manuali per Utopic 2
1
Indice
Altri manuali DESi Serratura della porta
