DESi Utopic R OK Manuale utente
USER MANUAL
Wireless Motorized Cylinder
!
- If there is a problem with the device, first look to the troubleshooting part of this manual. If you cannot solve the
problem, contact your dealer.
- All the system needs to be protected from water, direct sunlight and shocks.
- Before using your motorized cylinder, Locking way (right or left handed door) and Number of turns should be adjusted
properly. Otherwise, the device will not work in the correct way and maybe broken.
- For emergency conditions, we recommend you to put the keys in an accessible place (like car, bag etc.)
GENERAL INFORMATION and WARNINGS
- If there is any problem with the door or the locking mechanism, first of all, those problems have to be solved. The door's
mechanical parts and locking mechanism have to work properly.
- Auto-rotating parts of the device can cause injuries during installation. BE CAREFUL!
- If you are leaving your home for an extended period of time, first fully charge your motorized cylinder and take your
mechanical key with you. If you would leave more than 2 months, after charging your motorized cylinder, either shift the
motorized cylinder to childlock mode or leave your device as it is connected to charger. Otherwise, the batteries of your
product would die due to deep discharge.
2
3
Wireless Fingerprint Readers
Control Options and Compatible Accessories
Wireless Auto-Locking Module
Wireless Home Automation Interface
Remote Controllers
Wireless Keypad
Remote Access Module
1x Wireless Motorized Knob
1x Charging Cable (USB)
1x Installation screws and Hex key
2. BOX CONTENT
(May vary according to model)
1. FEATURES OF THE DEVICE
Euro-Profile
Batteries and Battery Life
60* days (Both RF and BLE are active)
Compatible Cylinder Type
ISM RF 434 Mhz
According to DESi labratory tests, with a usage of 10
operations per day on a 2 turns lock, battery life of
motorized cylinder is as follows:
Structure
ABS Plastic
90* days (Either RF or BLE is active)
Communication Capability
Your motorized knob is equipped with rechargeable Lithium
Ion batteries.
Bluetooth Low Energy
4
3. PARTS OF DEVICE and INSTALLATION (TYPE A)
1.STEP
Remove
existing
cylinder.
2. STEP
Install
motorized
cylinder and
tighten
the screw
Control Buttons
Handle for
Manual
Operation
Charging Port
(microUSB)
Fixing Screws
(4 pcs)
Fixing Screws
(4 pcs)
Slot for
The Modified Key
VERTICAL HORIZONTAL
Min.
2 mm
Outside
The existing
cylinder should
come out, at least
2 mm to be caught
by motorized knob
Type A.
Important
5
INSTALLATION (TYPE A)
- Insert one of exiting keys to the cylinder and mark it 5 mm from the surface of cylinder.
-Take out the key and saw o the head of the key fom marked line. You may need some tools like vice, hacksaw etc. Use a
rasp to smooth the edges. DESi accepts no liability for damages.
- Insert modified key to cylinder and verify that it is cut in a proper way.
- Install the motorized knob on the cylinder where the arrrows on the key slot point upward and the modified key is in
the position that it can be taken out from the cylinder without rotating (could be either horizontal or vertical.)
- First tighten 4 fixing screws lightly, then tighten them firm.
Follow the steps below to install motorized knob to the existing cylinder:
5 mm
Cut the key. Keep the modified key in
the position that it can be
taken out. Don’t rotate!
Install the motorized knob
on the cylinder. The arrows on
the key slot should point upward.
Tighten the 4 fixing
screws.
MODIFIED KEY
MODIFIED KEY
6
Control Buttons
Handle for
Manual Operation
Charging Port
(microUSB)
4. PARTS OF DEVICE and INSTALLATION (TYPE B)
5 mm
Slot for
The Modified Key
Min.
4 mm
Outside
The existing
cylinder should
come out, at least
4 mm to be caught
by motorized knob
Type B.
Important
Fixing
Screws
(2 pcs)
Gripping
Screws
(2 pcs)
The Slot for Modified Key
VERTICAL HORIZONTAL
MODIFIED KEY
MODIFIED KEY
In some
models
MODIFIED KEY
(2 way slot) (1 way slot)
7
- Take out the key and saw o the head of the key fom marked line. You may need some tools like vice, hacksaw etc. Use a
rasp to smooth the edges. DESi accepts no liability for damages.
- Insert modified key to cylinder and verify that it is cut in a proper way.
- Install the motorized knob on the cylinder where the arrrows (if exist) on the key slot point upward and the modified key
is in the position that it can be taken out from the cylinder without rotating (could be either horizontal or vertical.)
- First tighten 2 gripping screws and then tighten 2 fixing screws.
If your device has 2 way slot, mark the key 5 mm from the surface of cylinder.
If your device has 1 way slot, mark the key 7 mm from the surface of cylinder.
INSTALLATION (TYPE B)
Follow the steps below to install motorized knob to the existing cylinder:
- Insert one of exiting keys to the cylinder.
5 or 7 mm
Cut the key in accordance
with slot type of your
motorized knob.
Keep the modified key in
the position that it can be
taken out. Don’t rotate!
Install the motorized knob to
the cylinder. If it has 2 way slot,
the arrows should point upward.
First, tighten 2 gripping
screws and then,
tighten 2 fixing screws.
MODIFIED KEY
MODIFIED KEY
MODIFIED KEY
- Touch the UTOPIC line, enter a name for your device and touch the “green tick”. If a confimation pop-up appears, confirm
and device recognition process will start. If the matching is successful, you will hear 2 short tones from motorized cylinder
and your mobile phone will be master controller of motorized cylinder.
- On application screen, touch “+” on the top left corner to see the list of Utopic motorized cylinders around.
- Press and hold two buttons on motorized cylinder until you hear a long warning tone and then release buttons. After that
you will hear a short warning tone.
All the requested permissions need to be given without any restriction.
5.1. ENROLLING A MOBILE PHONE AS MASTER CONTROLLER
5. SETTING UP YOUR DEVICE
NOTE: For Android phones, when you are installing the app, it will ask permissions.
Otherwise, the app may not work properly.
- Search “Desi Utopic” on application stores. Download, install and run the application.
- Choose desired language and define a password or skip it.
8
DETAILS OF MOBILE APPLICATION
The first controller enrolled to motorized cylinder is accepted as the master controller.
The rest of the controllers will be user controllers.
Both, master and user controllers can be used to lock/unlock the motorized cylinder.
Besides, only the master controller can change settings of motorized cylinder.
Before using your motorized cylinder, you should adjust it properly by setting
“locking way” and then “number of rotation” according to your lock.
If you want to change the master controller of motorized cylinder, please check
“HOW TO RESET MOTORIZED CYLINDER” topic on the last page.
NOTE: For Android phones, when you are installating the application, it will ask permissions.
All the requested permissions need to be given without any restriction.
Otherwise, the application may not work properly.
9
10
PASSWORD: You can disable, enable or change the password of application.
5.2. APPLICATION SETTINGS
LANGUAGES: You can change language of the application.
If you touch the menu button in the top right corner when it is not connected to motorized cylinder, you will reach settings
menu of application. Related menu items are as follows:
FAQ: You can see questions and answers about usage.
APPLICATION INFO: You can see the version of installed application.
VIDEOS: You can see videos about usage of motorized cylinder.
Menu
Button
Indice
Altri manuali DESi Serratura
