Detection Systems DS7080iP-32 Manuale utente

For additional information on system commands, see the DS7080iP-32 User’s Guide P/N 39425

Reference Guide

for the

DS7080iP-32 Two Partition

Control/Communicator

Turning Off (Disarming) your System

[PIN] + [Off]

Commands for other System Features

Chime Mode [PIN] + [#] [7]

Zone Test [PIN] + [#] [8] [1]

Event History Readback [PIN] + [#] [8] [9]

Battery Test [PIN] + [System Reset]

Communicator Test [PIN] + [#] [8] [2]

Fire Reset [PIN] + [System Reset]

Fire Trouble [PIN] + [Off] to silence, [PIN] + [System Reset] to clear

Remote Program Dial-out [PIN] + [#] [8] [3]

Remote Program Answer [PIN] + [#] [8] [6]

Local Battery/Sounder Test [PIN] + [#] [8] [5]

Error Display [PIN] + [#] [8] [7]

Error Display Reset [PIN] + [System Reset]

Clear Zone Bypass [PIN] + [Bypass] [*] to clear

Access Control

[Access Control PIN] + [Off]

Keypad Quick Reference Guide

Turning On (Arming) your System

[PIN] + [On]

[PIN] + [No Entry] [Perimeter Only]

[PIN] + [Perimeter Only]

[PIN] + [No Entry] [On]

[PIN] + [#] [4]

[PIN] + [Arming Sequence] + [Bypass]

[PIN] + [Bypass] + [2-digit Zone number]

[PIN] + [#] [9] [9]

[PIN] + [OFF]

Normal Arming

Perimeter Arming, no entry delay

Perimeter Arming, with entry delay

Maximum Security Arming

Custom Arming

Force Arming

Zone Bypass

Set Delayed Arming

Delay Auto Arm by 15 Minutes

Change Partitions [PIN] + [#] [#]

Armed

Status

Power

Fire

123

456

789

Entry

System

Reset

Bypass

Only

Perimeter

Off

Armed

Status

Power

Fire

123

456

789

Entry

System

Reset

Bypass

Only

Perimeter

Off

Perimeter

Supervisory

Bell Silenced

Trouble

12345678

Ready To Arm

DS7447 DS7445

Downloaded from: http://www.guardianalarms.net

Table of Contents

1.0 Specifications ............................................................ 4

1.1 EnclosureHousing ............................................................. 4

1.2 Temperature ....................................................................... 4

1.3 Power ................................................................................. 4

1.3.1 Accessory Power ......................................................4

1.4 Outputs .............................................................................. 4

1.5 Zones ................................................................................. 4

1.6 Keypads ............................................................................. 4

1.6.1 DS7443 Keypad ........................................................4

1.6.2 DS7445/DS7447 Keypads ........................................4

1.7 Communicator .................................................................... 4

1.8 Users ................................................................................. 4

1.9 LightningProtection............................................................. 4

1.10 Burglar/FireZoneInputs ..................................................... 4

1.11 FireSignalInitiatingCircuit(2-wiremode)............................ 4

1.12 StandbyCurrentLoad......................................................... 5

2.0 Enclosure Installation ............................................... 5

2.1 Install theEnclosure............................................................ 5

2.2 InstalltheControl/Communicator ........................................ 5

3.0 Control Terminal Wiring ............................................ 6

4.0 SystemWorksheet ..................................................... 7

5.0 SystemOverview....................................................... 9

6.0 Glossary ................................................................... 10

6.1 ZoneProgramming ........................................................... 10

6.2 OutputProgramming......................................................... 11

6.3 GeneralControlProgramming........................................... 11

6.4 KeypadAssignment Programming .................................... 12

6.5 EX8Expansion Module Programming ............................... 12

6.6 EmergencyKeyProgramming .......................................... 12

6.7 CustomArming Programming ........................................... 12

6.8 ReportControlProgramming ............................................ 12

6.9 Day MonitorReportControl .............................................. 12

6.10 PhoneNumberGeneralControlProgramming .................. 13

6.11 PhoneAnsweringProgramming ........................................ 13

6.12 SystemTimers.................................................................. 13

6.13 ForceArmingProgramming .............................................. 13

6.14 ReportProgramming......................................................... 13

6.15 EventHistory ReadbackControl....................................... 14

6.16 FCCComplianceNotice ................................................... 15

6.17 FCCPhone ConnectionNoticeToUsers .......................... 15

6.18 CanadianDept.ofCommunications................................... 15

6.19 ForInstallationsinNewZealand ....................................... 15

7.0 Operating Guide ...................................................... 16

7.1 Fire Safety ........................................................................ 16

7.1.1 If Installed in Family Residences ............................16

7.1.2 Having and Practicing an Escape Plan ..................16

7.1.3 Installation Considerations ......................................16

7.2 Setting theDate ................................................................ 17

7.3 SettingtheTime ................................................................ 17

7.4 Personal Identification Numbers ........................................ 18

7.4.1 General Information.................................................18

7.4.3 PIN Authority Levels................................................18

7.4.2 Removing a PIN ......................................................18

7.5 Automatic Arming ....................................................19

7.6 Delayed Automatic Arming......................................19

7.7 Error Displays .................................................................. 20

7.8 Remote Program Dial-out andAnswer .............................. 20

7.9 Zone Test.......................................................................... 21

7.10 Battery/SounderTest ...................................................... 21

7.11 CommunicatorTest ........................................................... 22

7.12 Event History Readback ................................................... 22

8.0 How to Program the DS7080iP-32 .......................... 23

9.0 Programming the DS7080iP-32 .............................. 23

9.1 Address 001 -EX8ZoneExpansionModuleControl ......... 24

9.2 Address 002 - General Control ......................................... 24

9.3 Address 003 - User Controls ............................................ 25

9.4 Address 004 - Programmer and Master Codes ................. 25

9.5 Address 005 - Cross-Zoning ............................................ 25

9.6 Address 006 -Trip window ................................................ 25

9.7 Address007 - KeypadAssignment ................................... 26

9.8 Address 008 - LanguageandArmingControls .................. 26

9.9 Address 009 -OutputProgramming.................................. 26

9.10 Address 010 -Time Delays............................................... 27

9.11 Address 011 - Report Controls ......................................... 27

9.12 Address012 -Phone Controls .......................................... 28

9.13 Address 013 - Partition 1 Account Codes.......................... 28

9.14 Address 014 - Partition 2 Account Codes.......................... 28

9.15 Address 015 - Phone # 1 Format ...................................... 29

9.16 Address 016 - Phone # 2 Format ...................................... 29

9.17 Address 017 - 022 - Phone Numbers................................ 30

9.18 Address023- Dial Attempts ............................................. 30

9.19 Address 024 - AutoTest / Remote Programmer Call-Out Day

9.20 Address025 - AutoTest / RemoteProgrammerCall-OutTime

9.21 Address 026 - AC Report Delay........................................ 31

9.22 Address 027 - History Controls......................................... 31

9.23 Address 028 - Special Keys.............................................. 31

9.24 Addess 029 - Keypad Reports .......................................... 32

9.25 Address 030, 031, 032, 033 - ZoneType........................... 32

9.26 Address034, 035, 036,037 - ZoneAction ........................ 34

9.27 Address 038, 039, 040, 041 - OutputType ........................ 34

9.28 Address 042, 043, 044, 045 - Zone Bypass ...................... 35

9.29 Address046, 047, 048,049 -CustomArming ................... 35

9.30 Address050,051, 052, 053 -ZonePartitionAssignment .. 35

9.31 Addresses 054, 055, 056, 057 - Zone Alarm Reports ........ 36

9.32 Addresses 058, 059, 060, 061 - Zone Restoral Reports.... 36

9.33 Addresses 062, 063, 064, 065 - ZoneTrouble Reports...... 37

9.34 Addresses 066, 067, 068, 069 -Trouble

Restoral Reports.............................................................. 37

9.35 Addresses 070, 071, 072, 073 - Zone Bypass Reports .. 37

9.36 Addresses 074, 075, 076, 077 - Bypass

Restoral Reports.............................................................. 37

9.37 Address 078 - Open/Close Reports ................................ 38

9.38 Address 079 - AC/Battery Reports .................................. 38

9.39 Address 080 - Remote/Local Programming Reports ...... 38

9.40 Address 081 - Exit Error, Recent Closing, System Trouble,

System Trouble Restoral Reports ..................................... 38

9.41 Address 082 - Test Reports ............................................. 38

9.42 Address 083 - 116 - Alpha Labels ................................... 39

9.43 Address 117 - Point Expansion Module Missing Report . 39

9.44 Address 118 - Point Expansion Module Missing Restoral

Report ............................................................................... 39

9.45 Address 119 - Point Expansion Module Tamper Report.. 40

9.46 Address 120 - Point Expansion Module Tamper Restoral

Report ............................................................................... 40

9.47 Address121-Point Expansion Module FaultReport ......... 40

9.48 Address122-PointExpansion Module FaultRestoralReport

9.49 Address 123 - Octal Relay Control and Reports ............... 40

9.50 Address124-DefaultProgramming ................................. 41

10.0 Installation Guide for UL Listed Systems ............. 42

10.1 DS7080iP-32ULListings: ................................................. 42

10.2 InstallationConsiderations ................................................ 42

10.2.1 Special Requirements for Partitioned Systems......43

10.3 ProgrammingtheDS7080iP-32 ......................................... 43

10.3.1 Household Fire Alarm..............................................43

10.3.2 Grade A Household Burglary Alarm .......................43

10.3.3 Local Burglary Alarm ...............................................43

10.3.4 Police Station Connection........................................44

10.3.5 Central Station Burglary Alarm................................45

10.4 UsingtheAdemcoAB-12Bell/Housing.............................. 46

11.0 Report Programming Suggested Values ............... 47

11.1 Personal Dialing and PagerFormat ................................... 47

11.2 PagerFormat ................................................................... 47

11.3 SuggestedValues forBFSK and other Pulse Formats ....... 49

12.0 Report Programming Values Sent ......................... 50

12.1 SIAFormat ....................................................................... 50

12.2 ContactIDFormatValues Sent ......................................... 51

12.3 HighSpeed4/9Format ..................................................... 52

13.0 ProgrammingAddresses........................................ 54

14.0 Troubleshooting Guide ........................................... 55

Index ................................................................................. 58

1.0 Specifications

1.1 Enclosure Housing

The standard enclosure is manufactured from 20 Ga., cold-rolled

steel, and measures 12.5 in. Wide, by 14.5 in. High, by 3 in. Deep

(31.8 cm W x 36.8 cm H x 7.6 cm D). A keyed lock is included, and

thisenclosure hasa provisionforanoptional tamperswitch(required

for Commercial Burglary applications) for monitoring the door.

1.2 Temperature

• StorageandOperatingTemperature: +32°to +120°F (0°to +49°C)

1.3 Power

• Input power: 16.5 VAC, 40 VA, 60 Hz.

• Auxiliary regulated power: 11.8 -12.5VDC, 1.0 A.

(200mA

for UL Listed Systems. 1.0 A

not investigated by UL.)

• Optional Standby battery (P334): 12 V, 7.0 AH

• Control panel current draw: 150 mA

1.3.1 Accessory Power

• DS7443 keypad current draw: 45 mA, Standby & Alarm

• DS7445 keypad current draw: 75 mA, Standby & Alarm

• DS7447 keypad current draw: 100 mA, Standby & Alarm

• DS7488 Octal Relay 10 mA for the module plus 40

mA for each energized relay

• EX8 Expansion Module: 35 mA, Standby & Alarm

The total current for all auxiliary devices, including keypads

and smoke detectors = 1.2 A standby and alarm.

1.4 Outputs

• Alarm Output: Normally Closed, 1.0 Amp contact connected

to auxiliary power. Can be programmed for

steady or pulsed output.

• Programmable Output 1*: Solid state current sink (1 A max.).

(200mA for UL Listed Systems.1 A

not investigated by UL.)

Can be

used for alarm, arming state, or ac-

cess control.** This output is gen-

erally programmable.

• Programmable Output 2*: Solid state voltage source (500 mA

max.).

(200mA for UL Listed

Systems. 500mA not investigated

by UL.)

This is the smoke power

reset for Zone 1 when it is used as

afire zone for 2-wire smoke

detectors. Can be used for alarm,

armingstate, or access control.**

* = Current draw should be subtracted from either maximum

auxiliary or maximum alarm current draw.

** = Not investigated to the requirements of UL294.

1.5 Zones

• 1 or 2 Partitions.Zones may be assigned to one or both partitions.

Zones assigned to both partitions become common zones.

• 8zones,plus 1troublezone onthe maincontrol board.Thetrouble

zone cannot be assigned to a partition.

• 24 Expansion zones using EX8 Zone Expansion Module. Each

EX8 adds 8 additional zones. Up to three EX8 modules can be

added to the system.

• On Board Zone Response Time: 300 milliseconds.

1.6 Keypads

1.6.1 DS7443 Keypad

• Total number of keypads: 4 Keypads

• Maximum wire length each run: 400 feet (122m)

• Maximum wire length total: 1600 feet (488m) in system

• Wire type: 4 conductor, unshielded, #22 AWG (0.8mm) or 18

AWG (1.0mm) "Telephone quad".

Onlyone DS7443 is allowedpercable.EachDS7443must

have a “home run” back to the DS7080iP-32.Do not “daisy

chain” or place two DS7443 keypads on any cable run.

1.6.2 DS7445/DS7447 Keypads

• Total number of keypads: 4 Keypads

• Maximum wire length each run: 1000 feet (305m)

• Maximum wire length total: 4000 feet (1220m) in system

• Wire type: 4 conductor, unshielded, #22 AWG (0.8mm) or 18

AWG (1.0mm) "Telephone quad".

If using #22 AWG (0.8mm) wiring, there can be no more

than twokeypads allowed on any 1000 foot (305m) run.

Three keypads are allowed on any 1000 foot (305m) run if

#18 AWG (1.0mm) wire is used. Keypad wiring can be

“daisy-chained” or “home-run,” but the cables can NOT be

shared with other devices (e.g. telephone or siren wiring).

The DS7488 and EX-8 can only be “home-run.”

1.7 Communicator

Will report to two phone numbers with full single, double and back-

up reporting. Communicates in SIA, 3/1, 3/1 Ext., 4/1, 4/2, BFSK,

Contact ID, High Speed 4/9, and Pager formats.

The ringer equivalence is 0.1B

1.8 Users

The system allows up to 24 individual users.Each user will have his

own PIN number (the 4- or 6-digit code entered at the keypads) and

his own authority level (to determine which functions he may

perform).

1.9 Lightning Protection

MOVs and spark gaps provide protection from lightning surges and

static discharges.

1.10 Burglar/Fire Zone Inputs

• Number of circuits 8 Circuits

• End-of-line resistor 2.21k ohms

1.11 Fire Signal Initiating Circuit (2-wire mode)

The Fire circuit (zone 1) will work with 2- or 4-wire detectors. It has

an optional alarm verification.

• Number of 2-wire circuits: 1 circuit, compatibility identifier A

• Type of circuit: Class B, latching

• End-of-Line resistor: 2.21k ohms

• Supervisory current: 5 mA

• Maximum current for alarm: 13 mA

• Maximum short circuit current: 25 mA

• Maximum line resistance: 65 ohms

• Circuit voltage range: 8.5 to 14.0 VDC

• Maximum detectors per zone: 20 detectors (2-wire)

• Total detector standby current: 2.5 mA

2.2 Install the Control/Communicator

The control is static sensitive. Make sure you touch

earth ground before handling the control. This will

discharge any static electricity in your body. Example:

Run the ground wire to the enclosure before handling

the control. Then keep holding the ground wire while

installing the control.

• Insert the three support posts into the control retainer holes as

shown in the diagram.

• Slide the top of the control into the retainer tabs (the slots under

the top frame).

• Once in the retainer tabs, the control will rest on the three support

posts.

• Secure the bottom of the enclosure by screwing the bottom three

holesthrough thesupportposts andthrough tothe controlretainer

holes.

Once the control is installed, be sure to connect its

ground wire to the top hinge of the enclosure (the

unpainted tab).

1.12 Standby Current Load

Rechargeable

Battery Size

4 AH

7 AH

8 AH

14 AH

15 AH

17.2 AH

Derated

2.825 AH

5.225 AH

6.025 AH

10.825 AH

11.625 AH

13.385 AH

Max. Standby

for 4 hours

590 mA

1.0 A

Max. Standby

for 8 hours

230 mA

530 mA

640 mA

1.0 A

Max. Standby

for 24 hours

100 mA

130 mA

330 mA

360 mA

440 mA

Max. Standby

for 48 hours

120 mA

160 mA

Max. Standby

for 60 hours

100 mA

Battery AH - (20% Storage + 0.375 AH’s Alarm)

The following table is the derated battery divided by hours minus the control standby (150 mA):

2.0 Enclosure Installation

The DS7080iP-32 control/communicator and the enclosure are

shipped together. The control, however, still needs to be installed

into the enclosure. Hardware for mounting the enclosure to a wall,

and the control to the enclosure is located in its own hardware pack.

2.1 Install the Enclosure

• Use the enclosure as a template and mark the top mounting holes

on the mounting surface.

• Pre-start the mounting screws for these two holes. Slide the

enclosure onto these mounting screws so that the screws move

up into the thinner section of the holes.Tighten the screws.

• Screwinthe remainingtwoscrews ineither setofbottom mounting

holes.

• Knock out the desired wire entrances on the enclosure.

• Use knock out bushings if conduit is not used.

3.0 Control Terminal Wiring

ZONES 1-8: Zones 1-8 are for connection of NO or

NC alarm contacts. These zones require a 2.21K ohm

resistor (P/N 25899) at the end of the loop. Power is

momentarily removed after a [PIN] [System Reset]

during a fire verification. Only zone 1 may be used for

compatible 2-wire smoke detectors (up to 20). Zone

programming is done in address 034 for zones 1-8.

18 19 20 21 22 23 24 25 26

KEYPAD*:

Up to 4 keypads may be

used.

910 11 12

RBGY

Keypad(s)*

DS7488

Octal

Relay

13 14 15 16 17

TRBL PO2 1 2 3 4 5 6 7 8

TRBL:Trouble Input. For

the connection of any

accessory that provides a dry

contact trouble output.

PO2: PO2 supplies 12-12.5 v

and up to 500 mA when

activated. PO2 function

programmed in address 009.

*= Maximum Wire length each.

DS7443: 400 ft. (122m) maximum wire length.

Total in system: 1600 ft. (488M). Each keypad must be

a “home run”. Do not “daisy chain” keypads.

Trouble input is

non-supervised.

Do not use an

EOL resistor.

DS7488 Octal Relay

and EX8 Expansion

Modules. 1000 ft.

(305m) maximum

wire length. Must be

"Home Run". Do not

"Daisy Chain" with

keypads. The

DS7488 and EX-8

can only be “Home

Run.”

Shared cable is not

allowed for keypad

expansion modules,

telephone, or siren

wiring.

Do not use shielded

or twisted pair cable.

IMPORTANT

EX8

Expansion

Modules

DS7445/DS7447: 1000ft. (305m) maximum wire length.

Total in system: 4000ft. (1220m). Keypads may be

“home run” or “daisy chained”. Maximum of 2 keypads

per run for #22 AWG (.8mm) or 3 keypads for 18 AWG (1.0mm).

Option Bus

Quick Connect

TYPICAL BURGLAR AND FIRE WIRING

Typical 2-wire

smoke detector

wiring

(for a list of

compatible 2-wire

smoke detectors,

see Technical Service

Note P/N 41150)

EOL

Resistor

Smoke

Detector

Zone 1 Only

14 15

Typical 4-wire smoke

detector wiring.

For example:

Detection System's DS250

in an MB4W base.

EOL

Resistor

EOLRelay

Smoke

Detector

EOL

Resistor

EOLRelay

Smoke

Detector

Zone 1 Only

Zones 2-8 Only

14 15 16

Danger of explosion if battery

is incorrectly replaced.

Replace only with the same or

equivalent type recommended

by the manufacturer. Dispose of

used batteries according to the

manufacturer's instructions.

CAUTION

Typical burglar

alarm loop wiring

Ground

Zone

Input

CAUTION: Incorrect connections may

result in damageto the unit.

This System is Power Limited except for the

Battery terminals. All wiring entering this

enclosure must be Power Limited.

Before servicing this

equipment, remove all

power including the

transformer and battery.

Also remove the phone

line connection.

WARNING

CAUTION:

An appropriate two pole

disconnect device must be

installed by qualified service

personnel, as part of the

building installation.

AC INPUT: Use a listed Class 2,16.5 VAC

40 VA transformer Model D1640

requires 60 Hz unswitched

dedicated outlet - do not share.

ALARM OUTPUT: Provides 12 VDC, special

application, up to 1 Afor powering bells, siren

drivers, etc. Function programmed in address

009.

–

AUX

PO1 PO1: Shorts to Auxiliary (-) when activated. Can sink

up to 1 A. Programmed in Address 009.

EARTH GROUND: Connected to a good earth

ground and to the cabinet cover.

AUXILIARY POWER: Provides 12 VDC, special

application, up to 1 A for powering detectors.

4.0 System Worksheet

4.0 System Worksheet (continued)

5.0 System Overview

•Description: The DS7080iP-32 Control/Communicator is a fully

integrated hard-wire security and residential fire alarm system.

- It can support up to 8 input zones, two partitions, 24 individual

users, and multiple output options.

- Up to 4 keypads may be used to provide user interface with the

system, as well as programming access for the installer.

•Zone: A zone is an input to the DS7080iP-32 Control/

Communicator. There are 8 hard-wired zones on the main circuit

board.

•Zone 1: This zone can be programmed as a Fire or Burglar zone.

It is the only zone capable of supplying power to 2-wire smoke

detectors.

- When programmed as a Burglar zone, an alarm results on an

open or short when the control panel is armed.

- If trouble is programmed, a trouble report is generated, and the

zoneisconsidered“Not Ready”only whenthezone isdisarmed.

- For Fire zone operation, see the Fire zone description in the

Glossary.

•Zones 2 - 32: These zonescan beprogrammed asFire orBurglar

zones.

- When programmed as a Burglar zone, an alarm results on an

open or short when the control panel is armed.

- If trouble is programmed, a trouble report is generated, and the

zoneisconsidered“Not Ready”only whenthezone isdisarmed.

- For Fire zone operation, see the Fire zone description in the

Glossary.

•Cross-Zoning: Each on-board zone (zones 1-8) may be cross-

zoned with any or all of the other on-board zones. You cannot

cross-zone with the expansion module (EX8) zones.

When a pair of zones (A and B OR B and A) are cross-zoned, an

alarm condition is not generated unless:

1) Both A and B are in alarm simultaneously, or

2) B is in alarm within N seconds of the clearing of A or A is in

alarm within N seconds of the clearing of B, where N is the time

programmed in address 006. This allows for a one-way trip

pattern.

If two zones are cross-zoned to each other (A with B AND B with A)

analarmcondition isnot onlygeneratedbyconditions 1and 2above,

but also if:

3) A is in alarm within N seconds of the clearing of B. This allows

for a two-way trip pattern.

An alarm condition will be generated any time the above

criteria is met.

- Zone overlap required. Each zone shall have the ability to

individually protect the intended area (i.e. motion detector

patterns overlap).

- The following zone types

can

be cross-zoned:

• Perimeter Instant (1)

• 24 Hour (2)

• Interior Home/Away (6)

• Interior Instant (7)

• Day Monitor (8)

• Interior Delay (D)

• Perimeter Homeguard (E)

- The following zone types

cannot

be cross-zoned:

• Disabled (0)

• Entry/Exit Delay #1 (3)

• Entry/Exit Delay #2 (4)

• Interior Entry/Exit Follower (5)

• Keyswitch Toggle (9)

• Keyswitch On/Off(A)

• Fire Zone with Verification (B)

• Fire Zone without verification (C)

• Perimeter Follower Homeguard (F)

4) Cross-zoning across partitions is not supported.

5) Cross-zoning with different zone types is not supported.

6) If the trip window is 000, the cross-zone time will be the duration

ofthe armcycle ofthe crossednon-24hour zones.24 hourzones

will have a 24 hour duration.

• Trouble Zone (TRBL): This non-supervised (requires no End Of

Lineresistor) zoneisintended for theuseof simpletamperdevices.

If tripped, this zone will generate a Control Trouble/System Fault.

This trouble will clear when the Trouble Zone loop is un-faulted.

- Trouble Zone is disabled by default.

- Trouble Zone has two modes of operation: Normally Open and

Normally Closed.

•EX8 Expansion Module: Up to three (3) EX8 Expansion Modules

(24 additional zones) may be added to the system. They must be

set for Option Bus Addresses 101, 102 and 103 respectively (see

the EX8 Installation Guide P/N 39565 for module addresses).It is

important that each module be set with a different address.Failure

to do so will result in improper communications with the EX8

modules and the zones associated with them.

•DS7488 Octal Relay:Ifinstalled, theoptionalDS7488 OctalRelay

will provide fixed outputs for predetermined panel conditions.The

DS7488 Octal Relay attaches to the keypad bus and must be set

for Option Bus Address 9.

Octal relay outputs will not operate during the first two

minutes after powering up the control panel.

The fixed outputs are:

-Output 1 - Zone Alarm: Follows any zone alarm (except Silent

and Invisible zones). Remains On until the zone restores, the

bell cutoff time expires or [PIN] + [Off] is entered.

-Output 2 - Zone Trouble: Follows any zone trouble. Latches

ON when any zone is in an abnormal condition.

-Output 3 - System Reset: Activates for 8 seconds when the

[PIN] + [System Reset] command is entered at any keypad.

-Output 4 - Panic/Duress: Latches ON when the Panic (C) key

is pressed for 2 seconds on any keypad or when a Duress

Code is entered into any keypad. The relay is released when

the command [PIN] + [Off] is entered at any keypad.

-Output 5 - System Trouble: This relay is ON when a system

trouble has occurred. Releases when the system trouble is

cleared.

-Output 6 - Low Battery:The relay is ON during a Low Battery

condition.

-Output 7 - Partial Arm: In a non-partitioned system the relay

isON when thesystem ispartially armed (ForceArm,Perimeter

Arm or zones bypassed). In a partitioned system, the relay is

ON when any partition is partially armed. The relay is reset

when the system (or partition) is disarmed or is fully armed.

-Output 8 - Armed: In a non-partitioned system the relay is ON

when the system is armed to any level. In a partitioned system,

the relay is ON when both partitions are armed to any level.

The relay is reset when the system or any partition is disarmed.

6.0 Glossary

6.1 Zone Programming

• Invisible Alarms: This is a zone programmed not to have an

alarm output or an alarm display (except when arming) at any

keypad when activated. Invisible Alarm zones are recommended

for holdup alarms. An alarm signal will be sent, but the keypad

display will not indicate an alarm while this zone is violated.

•Silent Alarms: This is a zone programmed to activate the visual

display at the keypad, but not audible signals.

- If this zone is also an entry zone, an entry tone will sound when

this zone is activated.

•Bypassing Allowed: This zone can be bypassed (shunted).This

is done using the bypass command ([PIN] + [Bypass] + [2-Digit

Zone Number]) or the force arming sequence ([PIN] + [Arming

Sequence] + [Bypass]).

•Alarm on Short: This zone will activate an alarm when its loop is

shorted.

•Alarm on Open: This zone will activate an alarm when its loop is

opened.

•Trouble on Open: Thisisa zoneprogrammedtoactivateatrouble

when its loop is opened and the system is disarmed.

- If the system is armed, this zone will activate an alarm if shorted

or opened.

- For 24-hour zones, regardless of the arming state of the panel,

this always remains as a Trouble on Open.

•Trouble on Short: Works like Trouble on Open, but activates a

trouble when shorted and disarmed.

•Perimeter Instant: This is a zone programmed to activate an

alarm even during the entry/exit delay period.

•24-Hour Zone: This is a zone programmed to activate when its

loop is faulted, even if the system is disarmed.

•Entry/Exit Delay #1: This zone is ignored during the entry/exit

delay period.

- If it is violated while the system is armed, it will activate a delay

for the amount of time programmed in Entry Delay Time #1.

The keypad pre-alert sounders will activate and the system

may be disarmed during this delay period.

- If the system is not disarmed during the entry period, this zone

will activate an alarm.

- If, at the end of an Exit delay, an entry/exit delay zone is faulted,

an exit error condition will activate.

- The Entry delay will begin as above and any outputs

programmed to follow burglar alarms will activate.

- Ifthe systemis notdisarmedduring thisdelayperiod, thecontrol

panel will send an alarm report and an exit error report.

- If the system is disarmed during this delay period, the alarm

outputs will deactivate and no alarm report will be sent.

• Entry/Exit Delay #2: Works in the same manner as the Entry/

Exit Delay #1 zone, except that it uses Entry Delay Time #2.

If both Entry/Exit delays have been activated, the control

will use the shorter delay.

• Interior Entry/Exit Follower: This is a zone programmed to be

ignored during an entry/exit delay and then become an interior

instant zone.

- If this zone is violated while the system is armed and no entry/

exit zones have been violated, it will activate an instant alarm.

- If this zone is violated after an entry/exit delay zone is violated,

it will follow that entry/exit delay time.

- This zone is bypassed when arming only the perimeter.

• Interior Home/Away: This zonebecomes anactiveinterior entry/

exit follower when the system is armed and an entry/exit delay

zone is violated during the exit delay time.

- If the system is armed and an entry/exit delay zone is not

violated, this zone will be bypassed.

- This zone is bypassed when arming only the perimeter.

• Interior Instant: This is an instant zone that does not use entry

delays. This zone is bypassed when arming only the perimeter.

• Day Monitor: This isa perimeter instantzonethat activatesalarm

outputs when the system is armed, but only activates the keypad

sounders when the system is disarmed.

- When the system is disarmed, any violation of this zone will

activate the keypad sounders which will sound continuously

until a disarming command is entered. The alarm outputs will

not operate.A trouble report (if programmed) will be sent to the

central station.

- A day monitor violation will be recorded in the alarm history.

• Keyswitch Input: This zone allows the system to be armed or

disarmed using a Normally Open momentary keyswitch (toggle

mode) or an on/off switch wired across the keyswitch zone.

- In toggle mode, each time the keyswitch input is shorted, the

arming state of the control panel will toggle.

- In the on/off mode, the control panel will arm when the zone is

shorted and will disarm when the zone is supervised.

- May be programmed to allow force arming.

- In the on/off mode, may be bypassed for keypad arming.

- Keyswitch zones should be programmed for trouble on open.

- If the keyswitch zone circuit is cut, a zone trouble and an alarm

(if armed) will be generated on this zone. Alarm output for this

zone is fixed at on steady.

- An output should be used for an LED to indicate armed/

disarmed status and for a sounder to indicate entry/exit delays.

• Fire Zone: This zonecauses afire alarm whenactivated,whether

the system is armed or disarmed.

- It can be silenced (but not reset) by entering a valid [PIN with

disarming privileges] + [Off].

- A fire alarm will be displayed on all keypads.

- A fire reset command [PIN] + [System Reset] must be entered

after silencing the alarm to re-enable this zone. It is important

to not use the panel during the 8 second reset period.

- If a fire alarm is not reset within 24 hours of the alarm being

silenced, “Fire Alarm…Not Reset” will appear on the display

with the keypad beeping every 10 seconds.

- If this zone is programmed for trouble and the loop opens, the

keypads willindicatea“FireTrouble”forthiszone andthe keypad

sounders will beep once every ten seconds.

- If the system is a combination fire and burglar alarm, the fire

alarm has priority over the burglar alarm.

• Fire Zone with Verification: This zone is identical to a fire zone

except that after the first alarm, it will perform a fire reset and

then wait up to two minutes for a second alarm.

- If a second alarm occurs within this two minute period, the

system will instantly signal a fire alarm.

- If there is no second alarm within this two minute period, the

control panel will reset back to its normal condition.

Use of this control’s alarm verification feature may not be

permitted in your area. Check local codes.

Altri manuali per DS7080iP-32

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Detection Systems Telefono cellulare

Detection Systems

Detection Systems DS7400Xi-AT Manuale utente

Manuali Telefono cellulare popolari di altre marche

Zte

Zte BLADE A520 Manuale utente

Nokia

Nokia Lumia 620 Manuale utente

Blackbe;rry

Blackbe;rry KEYone Manuale utente

Bea-fon

Bea-fon X5 Premium Manuale utente

Blackbe;rry

Blackbe;rry 8707 Series Manuale utente

Blackbe;rry

Blackbe;rry Storm Istruzioni operative

LG LM-X420QN Manuale utente

LifeWatch

LifeWatch V Manuale utente

Bea-fon

Bea-fon SILVER LINE SL860 Manuale utente

IKI Mobile

IKI Mobile KF4.5i Manuale utente

Hitech

Hitech HT-850 Manuale utente

Yezz

Yezz Fashion F10 Manuale utente

Point Mobile

Point Mobile PM60 Manuale utente

Blackbe;rry

Blackbe;rry Q10 Manuale utente

Blackbe;rry

Blackbe;rry Bold 9900 Manuale utente

Blackbe;rry

Blackbe;rry STORM 9500 - VERSION 5.0 Manuale utente

LG LM-K420EMW Manuale utente

ISAFE MOBILE

ISAFE MOBILE IS655.2 Manuale utente