Detecto 750 Manuale utente

8555-M483-O1 Rev C x750 Owner’s 1

750

WEIGHT INDICATOR

With Body Mass Index Features

Owner’s Manual

Technical Support: Ph: 866-254-8261 xtechsupport@cardet.com

8555-M483-O1 Rev C x750 Owner’s

8555-M483-O1 Rev C x750 Owner’s 1

PRECAUTIONS

Before using this indicator, read this

manual and pay special attention to all

"NOTIFICATION" symbols:

IMPORTANT ELECTRICAL

WARNING

TABLE OF CONTENTS

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 1

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 1

Standard Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 1

Optional Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 1

SITE PREPARATION REQUIREMENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 2

INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 3

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 3

Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 3

Interconnections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 4

Load Cell Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 4

Serial and Bluetooth/Wi-Fi Interface Specifications . . . . . . . . . . . . . . . . . . . . . Page 4

Serial I/O Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 4

Optional AC Power Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 5

Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 5

Battery Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 5

Battery Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 5

Battery Installation/Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 6

WEIGHING UNITS SELECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 7

KEYPAD FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 8

Basic Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 8

Body Mass Index Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 9

ANNUNCIATORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 10

OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 11

Basic Weighing Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 11

Body Mass Index (BMI) Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 11

Weight Recall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 12

Serial ID Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 12

SETUP AND CALIBRATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 13

SETUP REVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 19

EVENT COUNTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 19

WEIGHT ON DEMAND FORMAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 20

SERIAL PRINT COMMANDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 20

ERROR AND STATUS DISPLAYS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 21

BEFORE YOU CALL SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 22

CARE AND CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 22

PARTS IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 23

APPENDIX A – INDICATOR MOUNTING BRACKETS . . . . . . . . . . . . . . . . . . . . Page 27

Serial Number ______________________

Date of Purchase ___________________

Purchased From ____________________

___________________________________

RETAIN THIS INFORMATION FOR FUTURE USE

8555-M483-O1 Rev C x750 Owner’s

FCC COMPLIANCE STATEMENT

This equipment generates, uses and can radiate radio frequency, and if not installed and used

in accordance with the instruction manual, may cause interference to radio communications. It

has been designed within the limits for a Class A computing device pursuant to Subpart J of

Part 15 of FCC rules to provide reasonable protection against such interference when

operated in a commercial environment. Operation of this equipment in a residential area may

cause interference in which case the user will be responsible to take whatever measures

necessary to correct the interference.

You may find the booklet “How to Identify and Resolve Radio TV Interference Problems”

prepared by the Federal Communications Commission helpful. It is available from the U.S.

Government Printing Office, Washington, D.C. 20402. Request stock No. 001-000-00315-4.

PROPER DISPOSAL

When this device reaches the end of its useful life, it must be properly disposed of. It must not

be disposed of as unsorted municipal waste. Within the European Union, this device should be

returned to the distributor from where it was purchased for proper disposal. This is in

accordance with EU Directive 2002/96/EC. Within North America, the device should be

disposed of in accordance with the local laws regarding the disposal of waste electrical and

electronic equipment.

It is everyone’s responsibility to help maintain the environment and to reduce

the effects of hazardous substances contained in electrical and electronic

equipment on human health. Please do your part by making certain that this

device is properly disposed of. The symbol shown to the right indicates that

this device must not be disposed of in unsorted municipal waste programs.

pictorial content, in any manner, is prohibited. No patent liability is assumed with respect to the

use of the information contained herein.

DISCLAIMER

While every precaution has been taken in the preparation of this manual, the Seller assumes

no responsibility for errors or omissions. Neither is any liability assumed for damages resulting

from use of the information contained herein. All instructions and diagrams have been checked

for accuracy and ease of application; however, success and safety in working with tools

depend to a great extent upon the individual accuracy, skill and caution. For this reason, the

Seller is not able to guarantee the result of any procedure contained herein. Nor can they

assume responsibility for any damage to property or injury to persons occasioned from the

procedures. Persons engaging the procedures do so entirely at their own risk.

CAUTION

CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT

TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

ATTENTION: RISQUE D'EXPLOSION SI LA BATTERIES EST REMPLACE'E PAR

UN TYPE INCORRECT. REJETEZ LES BATTERIES UTILISE'ES SELON LES

INSTRUCTIONS.

8555-M483-O1 Rev C x750 Owner’s 1

INTRODUCTION

Thank you for purchasing our 750 Weight Indicator. It has been manufactured with quality and

reliability and has been tested before leaving our factory to ensure accuracy and dependability

for years to come.

This manual is provided to guide you through installation, operation and maintenance of your

indicator. Please read it thoroughly before attempting to install or operate your indicator and

keep it available for future reference.

SPECIFICATIONS

Power Requirements . . . . . . . . Six “AA” Alkaline, Ni-Cad or NiMH batteries (not included)

OR an optional 100 to 240 VAC 50/60Hz 12 VDC 1A wall

plug-in UL/CSA listed AC power adapter (Cardinal part

number 6800-1045). Models are available with the AC

adapter included.

Operating Temperature . . . . . . 14 to 104 ºF (-10 to +40 ºC)

Display . . . . . . . . . . . . . . . . . . . Six-digit, seven segments, 0.7-inch-high LCD

Sensitivity . . . . . . . . . . . . . . . . . 0 to 2.4 mV/V

Signal Input Range . . . . . . . . . 0 to 12mV max.

Transducer Excitation . . . . . . . 5.0 VDC

Resolution . . . . . . . . . . . . . . . . 2,500 divisions

Capacities . . . . . . . . . . . . . . . . up to 10,000 divisions noncommercial

Division Value . . . . . . . . . . . . . 1, 2, or 5

Sample Rate . . . . . . . . . . . . . . 1 to 16 samples per second

Auto Zero Range . . . . . . . . . . . 0.5 or 1 through 9 divisions

Weighing Units . . . . . . . . . . . . . Pounds or Kilograms

Keyboard . . . . . . . . . . . . . . . . . Membrane type with 5 keys and 4 directional arrows

Enclosure Size . . . . . . . . . . . . . 6.125" W x 6.75" H x 1.75" D (16 cm x 17 cm x 4 cm)

Construction . . . . . . . . . . . . . . . Painted Steel

Standard Features:

xUnits Locking xSelectable Filtering

xAuto Shut-Off Feature xSerial I/O (Input/Output)

xSelectable Sleep-Mode xWi-Fi and Bluetooth, available in

Model 750C

Optional Features:

xOptional 12VDC AC Power Adapter

8555-M483-O1 Rev C x750 Owner’s

SITE PREPARATION REQUIREMENTS

The 750 Weight Indicator is a precision weight indicating instrument. As with any precision

instrument, it requires an acceptable environment to operate at peak performance and

reliability. This section is provided to assist you in obtaining such an environment.

Environmental

The 750 Weight Indicator meets or exceeds all certification requirements within a temperature

range of 14 to 104 °F (-10 to +40 °C).

In order to keep cooling requirements to a minimum, the indicator should be placed out of

direct sunlight and to provide adequate air circulation, keep the area around the indicator clear.

Do not place the indicator directly in front of a heating or cooling vent. Such a location will

subject the indicator to sudden temperature changes, which may result in unstable weight

readings.

Make sure that the indicator has good, clean AC power and is properly grounded. In areas

subject to lightning strikes, additional protection to minimize lightning damage, such as surge

suppressors, should be installed.

Electrical Power

The 750 Weight Indicator has been designed to operate from a 100 to 240 VAC 50/60Hz 12

VDC 1A wall plug-in UL/CSA listed AC power adapter (Cardinal part number 6800-1045). Note

that a special order is not required for operation at 230 VAC.

The socket-outlet supplying power to the indicator should be on a separate circuit from the

distribution panel and dedicated to the exclusive use of the indicator.

The socket-outlet shall be installed near the equipment and shall be easily accessible.

The wiring should conform to national and local electrical codes and ordinances and should

be approved by the local inspector to assure compliance.

On installations requiring 230 VAC power, it is the responsibility of the customer to have

a qualified electrician install the proper power adapter plug that conforms to national

electrical codes and local codes and ordinances.

8555-M483-O1 Rev C x750 Owner’s 3

INSTALLATION

Unpacking

Carefully remove the indicator from the shipping carton and inspect it for any damage that may

have taken place during shipment. Keep the carton and packing material for return shipment if

it should become necessary. The purchaser is responsible for filing all claims for any damages

or loss incurred during transit.

Should your indicator come already installed on a scale, the following installation

instructions does not apply to you.

Mounting

To install the indicator on the bracket, place the screw heads on the back of the indicator into

the large end of the slotted holes in the bracket. Pull down to secure the indicator. The spring

plunger will lock the indicator to the bracket. See Figures No. 1, 2 and 3.

Figure No. 1 Figure No. 2

Figure No. 3

Load Cell

Connector

Spring

Plun

AC Power

Ada

ter

Spring

Plunger

Release

NOTE: The mounting

bracket on your scale

may be different than

the one shown in

Figures No. 2 and 3.

Refer to Appendix A for

other bracket types.

Serial I/O

Connector

8555-M483-O1 Rev C x750 Owner’s

5 4 3 2 1

9 8 7 6

1 2 3 4 5

6 7 8 9

INSTALLATION, CONT.

Interconnections

All input, output and power connections are made at the bottom rear panel of the indicator.

Refer to Figure No. 1 for the rear panel layout.

Load Cell Connection

The load cell cable connects to the indicator via a 9-pin "D" connector on the rear panel of the

indicator. Figure No. 4 shows the pin identification for the load cell connector. Make certain

that the pins are correctly identified before soldering a wire to them. Use the connector

retaining screws to hold the load cell cable connector securely to the rear panel.

Figure No. 4

NOTE: Pins 3, 4, 8, and 9 are not used.

Serial Interface and Bluetooth/Wi-Fi Specifications

The Serial interface and Bluetooth/Wi-Fi on the 750C Weight Indicator can be configured

during the setup and calibration procedure or during the setup review operation. Using either

method, it is possible to select the operation of the serial interface and Bluetooth/Wi-Fi.

The interfaces may be connected to a computer for transmission of weight and associated data

to a PC-based EMR (electronic medical record) software program. The data can be transmitted

on demand by pressing the PRINT key or on receipt of a command from the computer.

Serial I/O Port

The 750 RS-232 serial I/O port is a 9-pin "D" connector on the rear panel of the indicator.

Figure No. 5 shows the Serial I/0 connector along with the identity of the pins used. Make

certain that the pins are correctly identified before soldering a wire to them. Use the connector

retaining screws to hold the serial cable connector securely to the rear panel.

PIN NO. FUNCTION

2 DATA INPUT (RXD)

3 DATA OUTPUT (TXD)

5 SIGNAL GROUND (GND)

9 VCC or 5VDC

NOTE: Pins 1, 4, 6, 7, and 8 are not used.

Figure No. 5

NOTE: The Model 750C with Bluetooth and Wi-Fi does not have a RS-232

serial I/O port.

The 750 RS-232 serial interface can be configured during the setup and calibration procedure

or during the setup review operation. Using either method, it is possible to select the operation

of the serial interface as well as select the baud rate.

xThe baud rates supported are: 4800, 9600, 19.2K and 38.4K baud.

xThe data format is fixed at 8 bits, No parity, and 1 stop bit.

NOTE: The 750 indicator is shipped from the factory with the baud rate set to 9600 baud.

PIN NO. FUNCTION

1 + EXCITATION

2 - SIGNAL

5 SHIELD

6 - EXCITATION

7 + SIGNAL

8555-M483-O1 Rev C x750 Owner’s 5

INSTALLATION, CONT.

Optional AC Power Adapter

To power the 750 using the optional 12 VDC wall plug-in AC power adapter, connect the plug

from the adapter into the power jack on the back of the indicator, and then plug the power

adapter into the proper electrical outlet. Refer to Figure No. 1. On models requiring 230 VAC, it

is the customer’s responsibility to obtain the correct power adapter plug.

Batteries

The 750 can use 6 "AA" size Alkaline, Ni-Cad or NiMH batteries (not included). You must first

obtain and install the batteries before operations can begin. Batteries are contained in a

battery holder inside the indicator. Access is via a removable panel on the back of the

indicator. See Figure No. 6.

CAUTION! The 750 can be operated from Alkaline, Ni-Cad or NiMH batteries. All

six (6) batteries must be of the same type. They must all be Alkaline, all Ni-Cad or

all NiMH. DO NOT mix Alkaline and Ni-Cad or NiMH batteries.

WARNING! The AC power adapter is also used to recharge the batteries, when the

750 is operated from Ni-Cad or NiMH batteries. DO NOT connect the AC power

adapter to the 750 if using Alkaline batteries. Also, when using Alkaline batteries,

make sure the 0-3 setup option is disabled (set to 0). Refer to Setup and

Calibration or Setup Review.

Battery Status

The 750 will operate for up to 250 hours on new Alkaline batteries or for up to 100 hours on

fully charged Ni-Cad or NiMH batteries depending on the condition of the batteries (from new

to about 500 recharges). The battery bar graph on the display indicates the battery capacity in

4 steps:

4 segments - the full battery capacity is available,

3 segments - the battery is at 75% of capacity,

2 segments - the battery is at 50% of capacity,

1 segment: - the battery is at 25% capacity.

When the battery voltage drops too low for accurate weighing, the indicator will show !6;

and then shut off. You will be unable to turn the indicator back on until the Alkaline batteries

have been replaced or if using Ni-Cad or NiMH batteries, the AC power adapter is connected

to the indicator to power it and recharge the batteries.

Battery Charging

To recharge the Ni-Cad or NiMH batteries, the AC power adapter must be connected to a

power outlet and plugged into the indicator. It will take approximately 8 to 10 hours to fully

recharge the batteries. Charging the batteries for more than 10 hours will not damage them.

NOTE: The indicator may be operated while the batteries are charging.

8555-M483-O1 Rev C x750 Owner’s

INSTALLATION, CONT.

Battery Installation/Replacement

To install or remove the batteries, the following steps should be followed:

1. Make sure the AC power adapter is

unplugged.

2. Remove the indicator from the scale

mounting bracket. (Referring to Figure

No. 3, pull the spring plunger down and

slide the indicator away from the

mounting bracket).

3. Turn the indicator over so that the display

is facing away from you.

4. Locate the rectangular panel on the back

of the indicator.

5. To install or replace the batteries, remove

the battery holder cover by pushing in on

the tab and lifting it up. Refer to Figure

No. 6.

6. If installing new batteries, referring to

Figure No.7 and the polarity markings

located in the battery holder, install 6 new

“AA” size batteries in the battery holder.

7. If replacing the batteries, remove all 6

batteries from the battery holder, and

then referring to Figure No.7 and the

polarity markings located in the battery

holder, install 6 new “AA” size batteries in

the battery holder.

8. After placing all 6 batteries in the holder,

replace the battery cover.

9. Turn the indicator over (display facing up)

and press the ON/OFF key.

10. If the display turns on, the batteries have

been installed correctly. If not, remove

the battery cover, and check for one or

more improperly positioned batteries.

11. Return the indicator to the scale

mounting bracket.

12. The indicator is now ready for operation.

Push in and

lift here

Figure No. 6

Figure No. 7

- +

+ -

- +

Battery

Cover

Altri manuali per 750

Indice

Altri manuali Detecto Accessori

Detecto

Detecto MedVue MV1 Manuale utente

Manuali Accessori popolari di altre marche

Hillco

Hillco 2810 Manuale utente

Siemens

Siemens QSA2700D Manuale dell'operatore

Contours

Contours ZY024 Manuale utente

Saivod

Saivod VS621 Manuale utente

Virtuox

Virtuox VirtuCLEAN 2.0 Manuale utente

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuale utente

Z-Wave

Z-Wave HSD-200Z Manuale utente

turck

turck FMX-IM-2UPLI63FX Manuale utente

Decagon Devices

Decagon Devices 10HS Manuale utente

UPPAbaby

UPPAbaby Cup Holder Manuale utente

Elko

Elko SmartSensor Leakage Wireless Manuale utente

Grizzly

Grizzly H8371 Manuale utente

Panasonic

Panasonic HG-T Series Manuale utente

IFM Electronic

IFM Electronic Efector 250 Series Guida di riferimento

DigiDesign

DigiDesign 888/24 I/O Manuale utente

PROZIS

PROZIS QUAY Manuale utente

patagonia

patagonia PSI Vest Manuale utente

SFC Energy

SFC Energy EFOY GO! Manuale utente