DeWalt DXST10000 Manuale utente
IMPORTANT:
Please read this manual carefully before assembling this
storage rack and save it for reference
DXST10000
TITAN INDUSTRIAL RACK
6-FOOT TALL / 4-SHELF
INSTRUCTION
MANUAL
3
SAVE THESE INSTRUCTIONS
This manual contains important safety and operating
instructions. Read all instructions and follow them with
use of this product.
TABLE OF CONTENTS
TECHNICAL SPECIFICATIONS 4
SAFETY 5
PARTS LIST 6
ASSEMBLY 8
OPTIONS 13
WARRANTY 14
TABLE OF CONTENTS
4
DXST10000
TECHNICAL SPECIFICATIONS
TOTAL CAPACITY 10,000 lb (4,535.9 kg)
*WHEN WEIGHT IS EVENLY DISTRIBUTED
CAPACITY PER SHELF 2,500 lb (1,133.9 kg)
*WHEN WEIGHT IS EVENLY DISTRIBUTED
HEIGHT 72” (182.8 cm)
WIDTH 77" (195 cm)
DEPTH 24" (61 cm)
WEIGHT 180.78 lb (82 kg)
TECHNICAL SPECIFICATIONS
5
SAFETY GUIDELINES
• Save all warnings and instructions for future reference.
• This manual contains important safety and assembly
instructions. Read all instructions and follow them with
the use of this product.
FPO
GENERAL SAFETY
• Keep work area clean and dry.
• Use correct/recommended tools for the job.
• Never leave tools unattended.
• Never force a part into place.
• Wear safety apparel.
• Wear safety glasses/goggles.
• Never crawl, sit, stand, or climb on a rack.
• Keep small parts away from children. Never leave a small child unattended while assembling.
• Always use common sense – your personal safety is your responsibility.
SPECIFIC SAFETY FOR WALL MOUNT BRACKET
• Serious or fatal crashing injuries can occur from furniture tipping over. To prevent this,
the rack must be secured to a wall, especially in earthquake-prone environments, where
surfaces are uneven, and where children and/or pets are present.
• Different wall materials require different types of fasteners. Use fasteners suitable for your
specific type of wall. If you are uncertain about what type of fasteners to use, then please
contact your local hardware store.
DO NOT EXCEED THE FOLLOWING WEIGHT LIMITS FOR THIS RACK
• Maximum load for each shelf: Up to 2,500 lb (1,133.9 kg) when weight is evenly distributed.
It is recommended that the heaviest load be placed on the bottom shelf.
6
DXST10000
PARTS LIST
No. Description
1 Vertical Beam
2 Pre-Bolted Vertical Assembly
3 Vertical Assembly Bolt
4 Crossbeam
5 Shelf Support Strap
6 Safety Strap With Weld Nut
7 Safety Strap Bolt
8 Wire Grid
9 Laminate Deck
No. Description
10 Locking Shelf Pin
11 Locking Grid Clip
12 Carriage Bolt
13 10 mm Nut
14 10 mm Wrench
15 4 mm Hex Key
16 4 mm Hex Bit
17 Wall Mount Bracket Assembly
3
BEFORE YOU BEGIN:
• Read all instructions thoroughly.
• Remove all components from the box, and lay them on the floor
in an orderly fashion.
• Keep this information for further reference.
FPO
6
13
14
15
16
17
2
2
4
8
20
12
24
3
1
16
12
2
2
1
1
1
1
Qty. Qty.
11
12
10
5
7
7
4
PARTS LIST
Tools Required for Rack Assembly: 4 mm Hex Key (included) OR 4 mm Hex Bit (included);
Rubber Mallet (not included)
1
9
2
8
8
DXST10000
ASSEMBLY
EXPANDABLE UPRIGHT FRAME INSTRUCTIONS
• Note: For ease of assembly, two (2) Vertical Beams feature
pre-bolted horizontal and diagonal beams.
STEP 1
• Place one (1) Vertical Beam and one (1) Pre-Bolted Vertical
Beam on the floor, parallel to one another (about 24”/60.9 cm
apart). The widest part of the teardrop-shaped hole pattern
on each beam should be facing upward (or away from you).
STEP 2
• Take the free end of the diagonal beam and insert it into
the free end of the top horizontal beam. Align the holes.
Insert both beams into the U-shaped bracket at the top of
the opposing Vertical Beam, and align the holes. Using the
included hex key or hex bit, thread a vertical assembly bolt
through the holes and into the weld nut that is attached to
the U-shaped bracket. Do not fully tighten the bolt.
STEP 3
• Swing out the bottom horizontal beam, and insert it into the
U-shaped bracket at the bottom of the opposing Vertical
Beam. Thread a vertical assembly bolt through the holes and
into the weld nut that is attached to the U-shaped bracket.
Do not fully tighten the bolt.
STEP 4
• Repeat Steps 1-3 to assemble the second upright frame.
Once both are assembled, fully tighten the bolts on all
four corners. Be careful not to over-tighten the bolts; there
should be no deformation of the U-shaped brackets and/or
horizontal beams.
(61 cm)
2 ft
TOP HORIZONTAL BEAM
BOTTOM HORIZONTAL BEAM
DIAGONAL
BEAM
24
(60.9 CM)
9
CROSSBEAM INSTRUCTIONS
•Note: It is recommended for one person to hold the upright
frames in place while a second person installs the crossbeams.
STEP 1
• There is a set of locking tabs at both ends of every
crossbeam. To begin assembly, take one crossbeam and
insert the tabs into two of the holes on the lower portion of
one upright frame. Engage the locking tabs into the holes
using a downward motion. The locking pin hole should be at
the top. Make sure the end of the crossbeam is flush against
the upright frame.
STEP 2
• Repeat for the opposite side of the upright frame. Tap
the ends of the crossbeam closest to the upright frames
with a rubber mallet until fully seated. The crossbeam and
locking tabs should easily slip into place. If they do not, then
recheck the alignment of the teardrop-shaped holes and
tabs. Too much force may damage the interlock between the
crossbeam and upright frame.
STEP 3
• Using the methods listed above, install another crossbeam
to the opposite side of the upright frames, parallel to the first
crossbeam you installed. Make sure both crossbeams are at
the same level.
STEP 4
• Continue by installing the last three sets of crossbeams to the
upright frames. Make sure the crossbeams are attached at the
same level on both sides.
ASSEMBLY
LOCKING
PIN HOLE
WARNING!
• Serious or fatal crashing injuries can occur from furniture tipping
over. To prevent this, the rack must always be secured to a wall,
especially in earthquake-prone environments, where surfaces are
uneven, and where children and/or pets are present.
FPO
10
DXST10000
ASSEMBLY
• Note: There are five (5) Shelf Support Straps and three (3)
Safety Straps with Weld Nuts for every set of crossbeams.
STEP 1
• Starting with the lowest set of crossbeams, place one shelf
support strap perpendicular to the crossbeams and insert
each end into the slots on each side of the crossbeam.
STEP 2
• Continue aligning the remaining four supports
perpendicularly across the beams, and secure them into
place. Repeat for the remaining three sets of crossbeams.
STEP 3
• Starting at the bottom of the rack, place the safety straps
between the crossbeams where the two sets of pre-drilled
holes are. Use a safety strap bolt to fasten the safety
straps to the crossbeams, and use the hex key or hex bit
to tighten completely. Repeat for the remaining three sets
of crossbeams.
SHELF SUPPORT AND SAFETY STRAP INSTRUCTIONS
Altri manuali per DXST10000
1
Indice
Altri manuali DeWalt Rack e supporto
DeWalt
DeWalt DXST10000EXT Manuale utente
DeWalt
DeWalt DE7035 Manuale utente
DeWalt
DeWalt DXST4500PBK Manuale utente
DeWalt
DeWalt DWE74911 Manuale utente
DeWalt
DeWalt DW7451 Manuale utente
DeWalt
DeWalt DXST10000 Manuale utente
DeWalt
DeWalt D24001 Manuale utente
DeWalt
DeWalt DE7450 Manuale utente
DeWalt
DeWalt DWE74911 Manuale utente
DeWalt
DeWalt DE7260 Manuale utente
DeWalt
DeWalt DWX725 Manuale utente
DeWalt
DeWalt DWE74911 Manuale utente
DeWalt
DeWalt DW7350 Manuale utente
DeWalt
DeWalt DCAVR332 Manuale utente
DeWalt
DeWalt DXST10000PBK Manuale utente
DeWalt
DeWalt DW7451 Manuale utente
DeWalt
DeWalt DWX723-XE Manuale utente
DeWalt
DeWalt DWST82800 Manuale utente
DeWalt
DeWalt DW723 Manuale utente
DeWalt
DeWalt DXST4500DK Manuale utente
