DexWeb Telecom VOIP-9001 Manuale utente
VOIP-9001 SIP Phone Http Setup Guide (V1.42)
VOIP-9001 SIP Phone Http Setup Guide
Ø
Configured by WEB
........................................................................................................2
Ø
Network Setting：
...........................................................................................................3
Ø
Audio settings:
.................................................................................................................5
Ø
Dial Plan settings:
...........................................................................................................7
Ø
SIP Protocol Setting：
.................................................................................................10
Ø
Other settings:
...............................................................................................................15
VOIP-9001 SIP Phone Http Setup Guide (V1.42)
2
When VOIP-9001 SIP phone is properly installed, you can set each
parameters through PC and Web browser.
Details please refter to 《VOIP-9001 SIP phone Spec and Install》
ØConfigured by WEB
Double click icon to open the IE browser. Input the IP address of the
phone into address bar ( ), and then input
password of the phone into the following page.
Fig 1.1 Http Setting
VOIP-9001 SIP Phone Http Setup Guide (V1.42)
3
Default password 1234 is ordinary password and super password is 12345678.
With Debug set 0[disable], please input super password; while Debug is not
set as 0[disable], please input ordinary password. Then click button.
The following configured page wills popup.
ØNetwork Setting：
Fig 1.2 Network Setting
●iptype: Set how IP phone gets relevant network parameters by selecting
corresponding item from drop down list.
nstatic ip: Select this item to authorize users set IP address, subnet
mask and router IP address of IP phone manually.
ndhcp: Select this item to enable DHCP mode. With this system, your
LAN or router automatically assigns all the required network parameters
to any device connected to it when the device log on. 9001 IP IP phone
is shipped from the factory with DHCP on. So, if your LAN or router is
configured to use DHCP addressing, the IP phone’s LAN parameters
will automatically be configured as soon as it is connected to the LAN or
router and powered up.
npppoe：Those ADSL and Cable Modem users please select this item
VOIP-9001 SIP Phone Http Setup Guide (V1.42)
4
for it is a protocol especially designed for them. With this system, ADSL
ISP automatically assigns all the required IP parameters to any device
connected to it when the device log on.
nmodem：If the IP phone used with modem, please select this item to
get relevant network parameters auto. Then please fill ID and pin into
ppp id and ppppin fields.
●ppp id: With pppoe or modem selected in iptype drop down list,
please enter the user name here.
●ppp pin: With pppoe or modem selected in iptype drop down list,
please enter the password here.
●local ip: With static ip selected in iptype drop down list, please enter
IP address of IP phone here.
●subnet mask: With static ip selected in iptype drop down list, please
enter subnet mask of IP phone here.
●router ip: With static ip selected in iptype drop down list, please
enter router IP address of IP phone here.
●dns: With static ip selected in iptype drop down list, please enter IP
address of DNS server here.
VOIP-9001 SIP Phone Http Setup Guide (V1.42)
5
●dns 2: With static ip selected in iptype drop down list, please enter
IP address of backup DNS server here.
●mac: MAC address is the physical address supplied by the Ethernet
NIC. 9001 IP phone is shipped from the factory with a unique algorism
MAC address printed on the back of the base.
ØAudio settings:
Fig 1.3 Audio Setting
●codec1: Set the priority 1 of the audio compression algorithm. The
options are g729，g7231，g711u，g711a , gsm, ilbc and null.
●codec2: Set the priority 2 of the audio compression algorithm. The
options are g729，g7231，g711u，g711a , gsm, ilbc and null.
●codec3: Set the priority 3 of the audio compression algorithm. The
options are g729，g7231，g711u，g711a , gsm, ilbc and null.
●codec4: Set the priority 4 of the audio compression algorithm. The
options are g729，g7231，g711u，g711a , gsm, ilbc and null.
VOIP-9001 SIP Phone Http Setup Guide (V1.42)
6
●codec5: Set the priority 5 of the audio compression algorithm. The
options are g729，g7231，g711u，g711a , gsm, ilbc and null.
●codec6: Set the priority 6 of the audio compression algorithm. The
options are g729，g7231，g711u，g711a , gsm, ilbc and null.
●vad: Enable/disable VAD (voice activity detection).
●agc: Enable/disable AGC.
●aec: Enable/disable VEC.
●audio frame: Set audio frames in RTP package. Minimum is 1 and
maximum is 8.
●g.723.1 high rate: enable/disable g.723.1 high rate. G.723.1 high rate
is 6.3kbps, low rate is 5.3kbps.
●ilbc payload : Set the payload type of RTP package whne ILBC codec
selected to DTMF delay. The value range is 96-255.
●jitter size : Set buffer size of RTP package. The value range is 0-32.
●handset in: Set the volume of handset input.
●handset out: Set the volume of handset output.
●ring type: Set ring type by selecting corresponding item from drop down
VOIP-9001 SIP Phone Http Setup Guide (V1.42)
7
list.
ndtmf : Set ring as ordinary rings in different frequency
nnot disturb: Set the phone do not ring by selecting this item.
nuser define：Set ring as music saved by user by selecting this item.
nAdvanced:Set ring used the individualized tone provided by system
(need system support).
●speaker out: Set the volume of handfree output.
●speaker in: Set the volume of handfree input.
ØDial Plan settings:
Fig 1.4 Dial Plan Setting
●use dialplan: Set whether use dial plan or use dial number by selecting
the corresponding item in drop down list.
ndisable: Do not use dial plan or dial number by selecting this item.
nenable: Use dial plan by selecting this item.
VOIP-9001 SIP Phone Http Setup Guide (V1.42)
8
ndialnum: Use dial number by selecting this item. With this item
selected, please enter the dial prefix into dial number field.
nprefix: Use specially service by selecting this item.
nHotline: Use Hotline function by selecting this item. With this item
selected, please enter the hotline number into dial number field.
●dial number: With dialnum selected in use dialplan drop down list,
please enter the dial prefix into this field according to requirement of log
in server.
●ddd code: With enable or dialnum selected in use dialplan drop
down list, set area code according to E.164 dial rule. For example,
Beijing is 10; Shanghai is 21.
●idd code: With enable or dialnum selected in use dialplan drop
down list, set country code according to E.164 dial rule. For example,
China is 86; U.S.A is 1.
●idd prefix: With enable or dialnum selected in use dialplan drop
down list, set international call prefix according to E.164 dial rule, such
as 00.
●ddd prefix: With enable or dialnum selected in use dialplan drop
down list, set long distance call prefix according to E.164 dial rule, such
as 0.
Note With dialnum seletcted in use dialplan drop down list, you can also set dddcode,
iddcode, iddprefix and dddprefix according to requirement of system.
VOIP-9001 SIP Phone Http Setup Guide (V1.42)
9
●innerline: Enable/disable innerline call by selecting corresponding items
from dropdown list.
ndisable: Disable call innerline by selecting this item.
nenable: enable call innerline by selecting this item.
●innerlineprefix: With enable selected in innerline dropdown list,
please fill the prefix number pick up to inner line, such as 0.
●Call waiting: Enable/disable call waiting by checking/unchecking the
box.
●forward number: Enter receiving forwarded calls phone number into
this field; If the IP phone used with modem, with modem item selected in
iptype list box, and then fill ISP number into this field.
●fwd noanswer: Forward calls without replying by checking this box.
Please enter receiving forwarded calls phone number into fwd number
field.
●fwd always: Forward all calls by checking this box. Please enter
receiving forwarded calls phone number into fwd number field.
●fwd busy: Forward calls if busy by checking this box. Please enter
receiving forwarded calls phone number into fwd number field.
●answer: Enter a number from 0 through 60 to set the entries of the
VOIP-9001 SIP Phone Http Setup Guide (V1.42)
10
seconds before the phone answer the call auto or forward the calls.
●Use digitmap: Enable/disable digit map by checking/unchecking the
box.
ØSIP Protocol Setting：
Fig 1.5 SIP Protocol Setting
●use service: Enable/disable service by checking/clearing this box. To
make calls through SIP Proxy Server, please check this box; otherwise,
phone can only make IP-to IP calls.
●register ttl : IP phone will send a keep-alive registration message to SIP
proxy server every “register ttl” seconds. The minimum value is 10,
maximum value is 65535. Default is 60.
●service type: This option is used to accommodate the miscellaneous
requirements of the system providers.
§Common: no special requirements
§Huawei: Use Huawei’s system
Altri manuali per VOIP-9001
1
Indice
Altri manuali DexWeb Telecom Telefono IP
