DF ROBOT 4Drawing Manuale utente
[ ]
4Drawing - Interactive Electronics Frame User
Manual
LeoYan @ DFRobot
6/18/2014
DFRobot All Rights Reserved CC BY-NC 3.0 CN
DFRobotAll Rights Reserved CC BY-NC 3.0 CN P a g e | 2
Table of Contents
Preliminary Assembling............................................................................................................. 3
1Preparation........................................................................................................................ 3
2Making the Frame ............................................................................................................. 4
3Hanging the Frame ............................................................................................................ 5
4Choosing hanging position: ............................................................................................... 5
5Electronic Setup................................................................................................................. 6
6Installing SMT Modules ..................................................................................................... 7
Further Steps........................................................................................................................... 11
1Audio Interactions ........................................................................................................... 11
2Ambient Light Interaction................................................................................................ 12
Controlling & Programing........................................................................................................ 14
1Plug & Play....................................................................................................................... 14
2Graphical Programming................................................................................................... 15
3Freestyle .......................................................................................................................... 20
Precautions：
A. This product contains small parts, not suitable for children under 6 years old and use.
B. This product is not waterproof and moistureproof function, please keep or use in a dry environment! Not
heavy can be stacked on top.
C. This product uses the USB or supporting the battery box power supply, the use of other power supply if the
above 5.5V may cause permanent damage to the products controller.
DFRobotAll Rights Reserved CC BY-NC 3.0 CN P a g e | 3
Preliminary Assembling
1Preparation
1) 4DrawingKit Parts List
You’ll be able to get this kit via DFRobot Online Store or resellers. In this kit you’ll find:
Parts/Compon
ents
Introduction
Amo
unt
Image
“Palette”
Controller
Based on Atmega32U4,
compatible with Arduino
1
LED Module
LED: Redx2, Greenx2,
Orangex2, Bluex2, Whitex2;
GNDx1
1
PIR Motion
Sensor
Detects whether a human
has moved in or out of the
sensors range
1
Front Frame
Front frame
1
Back Frame
Back frame
1
LED Cardboard
Holder
Inner cardboard in the
frame，it is use to hold LEDs
and etc.
1
Cardboard
Corner
Footpad for LED Cardboard
Holder
4
Aluminum Foil
278mm (L) 193mm (W)
Aluminum Foil for GND
2
Aluminum Foil
Sticker
84x conductive 20mm x
4mm Aluminum Foil Sticker
1
Micro USB
Battery Box
3x AA Batteries
1
Cable Set
22-24x Wires with DuPont
Head (15cm):
M/M：Red、Yellow，Blue.
Each about 5x;
F/M：Red、Yellow、Blue. Each
about 3x
Traceless Wall
Hook
For hanging
2
Push Pin
For marking
1
Masking Tape
1cm wide
1
Stick Glue
Stick glue
1
Contour
Contour drawing
2
DFRobotAll Rights Reserved CC BY-NC 3.0 CN P a g e | 4
Drawing
Frame Dimension：352x274x30mm
Canvas Dimension：A4 （210 x 297mm）or 12 x 9inch（228.6 x 304.8mm）
Frame Window Dimension：287 x 200mm（smaller than A4）
Frame Material：Paperboard, corrugated paperboard
Power Supply：3xAA or micro-USB
Battery Life：30 days with AA batteries（In standby mode, all modules will shut down automatically
except zone W.）
LED Module Interface：4 Channel 40Ma I/O Interface（Zone Z），4 Channel 500mAOutputInterface(Zone
X)
Extension Interface：4 Channel 3PIN for Sensor/Actuator（Zone S）/1 Channel UART/1 Channel I2C
Wakeup Interface：1 Channel 3PIN for Sensor (Zone W）
2Making the Frame
1）Making Frame Holder: glue the Cardboard Corners onto the LED Cardboard Holder
2）Making the pillars of Back Frame: fold to stand, then glue and keep till dry
front
back
DFRobotAll Rights Reserved CC BY-NC 3.0 CN P a g e | 5
3) Making the Front Frame: remove the dentate cover, separate carefully with knife or tear apart
Now you should have a paper frame ready!
3Hanging the Frame
1) Choosing hanging position: 4drawing can be hanged vertically or laterally. Locate the nails
with hollow area in the back of frame box, as shown in figure
DFRobotAll Rights Reserved CC BY-NC 3.0 CN P a g e | 6
2) Hammer the Traceless Wall Hook and hang the frame onto wall.
Now you have a way of showing off your paintings!
4Electronic Setup
1.1 Wiring the Modules
1）Insert batteries into battery box
2）Connect battery box with micro USB port on Palette
3）Connect PIR Motion Sensor with Zone W on Palette
1.2 Placing the Modules
1）Place the battery box in the middle of Back Frame, reinforce with sticky tape
2）Place the Palette Controller on one side
3）Place the PIR Motion Sensor onto the elliptic hole on the Back Frame, reinforce with tape
DFRobotAll Rights Reserved CC BY-NC 3.0 CN P a g e | 7
5Installing LED Modules
1.1 Installing LEDs
1）Fix the aluminum foil, if too large use scissors to cut to paper size (aluminum foil for circuit
"GND")
2）Fixing painting to Frame Holder: It support A4 and 9 "x 12" two paper specifications of the
installation; If painting is smaller than A4 size, can use A4 hollow out worked on ways to use.
3）Placing the LEDs, make a small hole on the planned area, and mark it for later use.
DFRobotAll Rights Reserved CC BY-NC 3.0 CN P a g e | 8
4）Stick the LEDs with Aluminum Foil Sticker onto the foil
1.2 Connecting LED Modules
DFRobotAll Rights Reserved CC BY-NC 3.0 CN P a g e | 9
1）Switch to “MAKE” on the Palette Controller, place the Frame Holder into frame box
2）Connect “-” in Zone Y with GND module, and place them in properly. This will connects the
foil with “GND” on the Palette controller.
3）Connect the first LED in cascade to Zone X or Zone Z accordingly, and wire them together. In
the demo, two red LEDs are grouped together, others will be grouped randomly.
DFRobotAll Rights Reserved CC BY-NC 3.0 CN P a g e | 10
4）Put wires in order and reinforce with sticky tape.
5）After testing, switch to “RUN” on Palette controller.
Now you will have a blinking drawing!
Indice
