DFI EC800-AL Manuale utente

EC800-AL Installation Guide

Package Contents

www.dﬁ.com

•

1 EC800-AL system unit

•

Mounting screws for Mini PCIe modules

• Accessories for M.2 modules

•

1 Quick Installation Guide

•

1 CD disk includes:

-Drivers / Manual

Panel

Rear View

Front View

Note:

The system offers another SKU with a different combination of display outputs: VGA + 2 Micro HDMI. It also

supports dual-display and triple-display functions: VGA + 2 Micro HDMI or DVI + 2 Mini DP.

DFI reserves the right to change the speciﬁcations at any time prior to the product's release. For the latest revision and details of the

installation process, please refer to the user's manual.

HDD LED

(blue)

Reset Switch

Power Button

(green)

USB 3.0

Remote Power

Switch

Mic-in

USB 2.0

Status LED

(blue)

LAN 1

LAN 2

COM 1

DC-in

COM 2 Line-out

Mini DisplayPort

Antenna hole

DVI-I

(DVI-D signal)

Antenna hole

4. Lift the cover to open the system. The M.2 and Mini PCIe sockets are readily

accessible after removing the bottom cover.

Removing the Chassis Cover

Please observe the following guidelines and follow the procedure to open the

system.

1. Make sure the system and all other peripheral devices connected to it have

been powered off.

2. Disconnect all power cords and cables.

3. The 4 mounting screws on the bottom side of the system are used to secure

the cover to the chassis. Remove these screws and then put them in a safe

place for later use.

Chassis screw

M.2 socekt

Mini PCIe socket

Installing an M.2 Card

To install a 42mm M.2 card:

1. Align the notch at the edge of the M.2 card with the key in the connector.

2. Insert the M.2 card into the connector.

3. Place the plastic spacer on top of the screw hole; push down on the other

end of the M.2 card and use the provided mounting screw (the longer one) to

secure the card on the system board.

The system is equipped with two M.2 sockets, supporting one M.2 22x42mm (B

key) and one M.2 22x30mm (AE key) form factor.

Mounting screw

To install a 30mm M.2 card:

1. Align the notch at the edge of the M.2 card with the key in the connector.

2. Insert the M.2 card into the connector.

3. Push down on the other end of the M.2 card and use the provided mounting

screw (the shorter one) to secure the card on the system board.

Mounting screw

Notes:

1. The 42mm M.2 slot provides PCIe, USB, and SATA signals (for common mobile

broadband and storage modules) whereas the 30mm M.2 slot provides only PCIe and

USB signals (for common Wi-Fi and Bluetooth modules).

2. To switch between PCIe and SATA signals for the 42mm M.2 slot, refer to Jumper

Settings below.

To install both 42mm and 30mm M.2 cards:

1. Align the notch at the edge of the 30mm M.2 card with the key in the

connector.

2. Insert the 30mm M.2 card into the connector.

3. Push down on the other end of the card and place the plastic spacer on top of

the card.

4. Insert the 42mm M.2 card into the connector.

5. Push down on the other end of the card and use the provided mounting screw

(the longer one) to secure both cards on the system board.

Mounting screw

Installing a Mini PCIe or an mSATA Card

Notes:

1. This Mini PCIe slot can accommodate either a Mini PCIe or an mSATA card; refer to

Jumper Settings for signal selection for this slot.

2. If installing a wireless module, route the antenna cable(s) along the side of the chassis

and underneath the system board to reach the antenna holes.

The system board is equipped with 1 Mini PCIe slot.

1. Grasp the Mini PCIe card by its edges and align the notch of the PCIe card

with the key in the connector on the system board.

2. Push down on the other end of the Mini PCIe card and use the provided

mounting screw to secure the card on the system board.

Mounting screw

Board Layout and Jumper Settings

Note:

You cannot use COM 2 and DIO at the same time.

Please set JP8 and JP9 together.

Reset

Power

DDR4

LAN 1

COM 2

JP6 JP1

Battery

LINE-out

Intel

WGI211AT

JP9

LAN 1

USB 3.0

USB 2.0

LAN 2 LAN 1

COM 1

MIC-in

DVI-I

Buzzer

DDR4

E3900 Series

Intel Atom

Intel

WGI211AT

Realtek

ALC262

JP3

JP2

JP8

Mini-PCIe/mSATA

COM 2/DIO

JP2, JP3

JP8, JP9

PCIe/SATA

Clear CMOS

JP1

JP6

SMBus (J19)

USB 2.0 (J3)

Power on/off (J11)

Standby LED

111

10 12

10 10

Clear CMOS Data JP6

Normal 1-2 On (default)

Clear CMOS 2-3 On

COM2 / DIO Pin Select JP8, JP9

COM 1-2, 4-5, 7-8,

10-11 On (default)

DIO 2-3, 5-6, 8-9,

11-12 On

Mini PCIe (CN15)

PCIe/SATA Select

JP2, JP3

mSATA 1-2 On

(default)

Mini PCIe 2-3 On

22x42mm M.2 (CN12)

PCIe/SATA Select

JP1

SATA 1-2 On

(default)

PCIe 2-3 On

www.dﬁ.com

A46801731

Altri manuali per EC800-AL

Indice

Manuali Scrivania popolari di altre marche

HP m9060n - Pavilion - Elite Scheda tecnica

Asus

Asus E210 Series Manuale utente

Dell

Dell Inspiron 600m Manuale utente

Dell

Dell Inspiron 3662 Manuale utente

TotalFlow

TotalFlow uFLO Manuale utente

HP Presario SV7000 - Desktop PC Manuale utente

HP ProDesk 400 G5 Manuale

Logitech

Logitech MK320 Manuale utente

Dell

Dell XPS 730 H2C Manuale utente

Sony

Sony Vaio Series Manuale utente

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manuale utente

Alto

Alto MD 250 Manuale utente

Lenovo

Lenovo ThinkCentre Edge 72 Manuale

Lenovo

Lenovo ThinkStation D20 Manuale

Arbor Technology

Arbor Technology FPC-7800 Series Manuale utente

Sony

Sony VAIO VGX-TP1 Series Manuale utente

Asus

Asus Eee Box B204 Manuale utente

Dell

Dell Optiplex 9010 All In One Manuale utente