DGSHAPE CA-DK2 Manuale utente

R2-220425

FA03098

User's Manual

Company names and product names are trademarks or registered trademarks of their respective holders.

Thank you very much for purchasing this product.

• To ensure safe use with a full understanding of this machine's performance, please be sure to read through this manual com-

pletely.

• Reproduction, citation, or translation, in whole or in part, of this manual is prohibited without the express written consent of

DGSHAPE Corporation.

• The contents of this operation manual and the specications of this product are subject to change without notice.

• DGSHAPE Corporation assumes no responsibility for any damage that may occur through use of this product, regardless of any

failure to perform on the part of this product or of any errors in this document. Damage includes but is not limited to damage

caused by the specications or performance of the product, damage caused by non-use of the product, and damage caused by

deliverables obtained through use of this product. Such damage can be either direct or indirect.

Supported models: DWX-52D / DWX-52DC / DWX-52DCi

http://www.dgshape.com/

Contents

Contents ...............................................................................................................................................................1

Before Use ............................................................................................................................................................2

Checking the Included Items ...........................................................................................................................2

Items to Prepare Yourself ..................................................................................................................................2

Advance Preparation ..........................................................................................................................................3

Usage Method.....................................................................................................................................................4

Room-temperature Polymerizing Resin ......................................................................................................5

Denture Base Cutting Method .................................................................................................................5

Complete Denture (Full Denture) Cutting Method .........................................................................8

Heated Polymerizing Resin ............................................................................................................................12

Denture Base Cutting Method ..............................................................................................................12

Complete Denture (Full Denture) Cutting Method ......................................................................17

Checking the Included Items

The following items are included with the kit. Make sure they are all present and accounted for.

CA-DK2-FX (15) CA-DK2-TR (15) Dedicated milling burs*1 Silicone stands (2)

*1: ZRB-150D, ZPB-100D, ZPB-50D, ZPB-30D

Memo

The CA-DK2-FX, CA-DK2-TR, and dedicated milling burs can be purchased separately.

Items to Prepare Yourself

• Items included with the machine

Adapter (1) Torque screwdriver (1)

• Materials, equipment, etc.

¾Room-temperature polymerizing resin or heated polymerizing resin

¾Pressure pot

¾Stand for adjusting the position of the polymerizing resin (This is used when adjusting the resin height during polym-

erization.)

¾Spatula (This is used when mixing together the powder and the liquid.)

¾Container (This is used when mixing together the powder and the liquid.)

¾Lidded container (This is used when mixing together the heated polymerizing resin powder and the liquid.)

¾Tissue paper (This is used to absorb the heated polymerizing resin's excess liquid layers.)

¾Polyethylene sheet (This is used to keep ngers from coming into contact with the heated polymerizing resin's excess

liquid layers.)

¾Vibrator (This is used to extract air bubbles from the container after the powder and the liquid have been mixed to-

gether.)

¾Acrylic resin adhesive (This is used to a󱐰x the CA-DK2-FX, the CA-DK2-TR, and articial teeth.)

¾Brush/eye dropper (This is used to apply adhesive.)

¾Articial teeth

Before Use

Advance Preparation

Add water to the pressure pot and prepare a stand that will position the CA-DK2-FX (room-temperature polymerization) or the

silicone stand (heated polymerization) within the range indicated by the water level gradations.

CA-DK2-FX Silicone stand

(room-temperature polymerization) (heated polymerization)

Before Use

This section explains how to create dentures with this kit. Room-temperature polymerizing resin or heated polymerizing resin

may be used.

There are two methods for creating dentures: the denture base cutting method in which the resin is polymerized before the

denture base is cut and the articial teeth are a󱐰xed and the complete denture (full denture) cutting method in which the

mold for the articial teeth is cut and arranged and the resin is polymerized before the complete denture (full denture) is cut.

The work procedure varies depending on the resin and method used.

Room-temperature polymerizing resin

• Denture Base Cutting Method (P. 5)

1. Create the denture

resin. (P. 5)

2. Mill the denture

resin. (P. 6)

3. A󱐰x the articial

teeth. (P. 7)

• Complete Denture (Full Denture) Cutting Method (P. 8)

1. A󱐰x the CA-DK2-

FX and the CA-DK2-TR.

(P. 8)

2. Cut the tooth mold

(the female mold for

the articial teeth) into

the TR. (P. 8)

3. Arrange the arti-

cial teeth on the TR.

(P. 9)

4. Create the denture

resin. (P. 10)

5. Mill the denture

resin. (P. 11)

Heated polymerizing resin

• Denture Base Cutting Method (P. 12)

1. Drill a hole in the CA-

DK2-FX. (P. 12)

2. Create the denture

resin. (P. 13)

3. Mill the denture

resin. (P. 15)

4. A󱐰x the articial

teeth. (P. 16)

• Complete Denture (Full Denture) Cutting Method (P. 17)

1. A󱐰x the CA-DK2-

FX and the CA-DK2-TR.

(P. 17)

2. Drill holes in the

FX and mill the tooth

molds into the TR.

(P. 17)

3. Arrange the arti-

cial teeth on the TR.

(P. 18)

4. Create the denture

resin. (P. 19)

5. Mill the denture

resin. (P. 21)

Usage Method

Room-temperature Polymerizing Resin

Denture Base Cutting Method

In this method, polymerize the resin, and then cut the denture base and a󱐰x the articial teeth.

1. Create the denture resin.

A Mix the room-temperature polymerizing resin powder and the liquid together well.

After mixing, use a vibrator to extract the air bubbles.

B Pour the mixture into the CA-DK2-FX (hereinafter referred to as the FX).

C Wait for the surface of the mixture to dry.

D Place the FX in the pressure pot.

E Check the pressure pot's water level.

Adjust the amount of water if it is not at the level indicated on the pressure pot.

F Set the pressure, temperature, and time on the pressure pot to polymerize the resin.

Set the values that are required in order for the room-temperature polymerizing resin being used to polymerize.

G After polymerization, cool the resin at room temperature.

Usage Method

2. Mill the denture resin.

A Remove the adapter cap.

Use a torque screwdriver to loosen the adapter's cap screws by turning them approximately four times each, and then re-

move the adapter cap.

B Attach the adapter base to the FX.

Align the edge of the adapter (A) with the edge of the FX (B).

C Attach the adapter cap.

D Tighten the cap screws (in four locations).

Tighten the screws until the torque screwdriver clicks.

Important

To x the part in place evenly, tighten the cap screws in order across the diagonals.

E Mill the denture.

Attach the FX to the machine, and then use the CAM data to mill the denture resin together with the FX.

Usage Method

3. A󱐰x the articial teeth.

A Remove the adapter.

B Use acrylic resin to a󱐰x the articial teeth.

Usage Method

Complete Denture (Full Denture) Cutting Method

Cut the tooth mold (the female mold for the articial teeth), arrange the articial teeth, polymerize the resin, and then cut the

complete denture (full denture).

1. A󱐰x the CA-DK2-FX and the CA-DK2-TR.

A Apply acrylic resin adhesive to the CA-DK2-FX (hereinafter referred to as the FX).

Measure approximately 0.5 ml of acrylic adhesive with an eye dropper, and then drip this adhesive onto the three locations

indicated in the gure so each location has adhesive with a diameter of approximately 5 mm.

Important

• To prevent tray deformation, do not apply too much adhesive.

• The surface on which adhesive is applied will have small air bubbles, but this is not a problem during milling.

B Attach the CA-DK2-TR (hereinafter referred to as the TR) by aligning its recessed parts with the protrusions on the

FX.

2. Cut the tooth mold (the female mold for the articial teeth) into the TR.

A Remove the adapter cap from the adapter.

Use a torque screwdriver to loosen the adapter's cap screws by turning them approximately four times each, and then re-

move the adapter cap.

B Attach the adapter base to the FX.

Align the edge of the adapter (A) with the edge of the FX (B).

Usage Method

C Attach the adapter cap.

D Tighten the cap screws (in four locations).

Tighten the screws until the torque screwdriver clicks.

Important

To x the part in place evenly, tighten the cap screws in order across the diagonals.

E Mill the tooth mold (the female mold for the articial teeth) into the TR.

Attach the TR to the machine, and then use the CAM data to mill the tooth mold to use in tting the TR with articial teeth.

F Loosen the cap screws, and then remove the adapter cap and the adapter from the FX.

3. Arrange the articial teeth on the TR.

A Apply one to two drops of acrylic resin adhesive to the TR's tooth mold.

B Check the shape of the tooth mold and the orientation of the articial teeth.

C Push the articial teeth onto the TR's tooth mold.

D Check that the articial teeth have been attached to the tooth mold without any gaps.

Important

The articial teeth have an orientation that matches the tooth mold. Attach teeth with the proper orientation.

Usage Method

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali DGSHAPE Utensili elettrici

DGSHAPE

DGSHAPE DWX-52DCi Manuale utente

Manuali Utensili elettrici popolari di altre marche

AEG

AEG OMNI-JS Manuale utente

SIP

SIP 01533 Manuale utente

Ribimex

Ribimex PRS499 Manuale utente

3M Fiber Optic Connector Crimp Tool Manuale utente

Ryobi

Ryobi P524 Manuale utente

ROJEK

ROJEK FSN 300A Manuale utente

Kemper

Kemper 1740PRO Manuale utente

WABCO

WABCO OptiTire Manuale utente

EINHELL

EINHELL TE-MS 18/210 Li Manuale utente

Orgapack

Orgapack OR-T 85 Guida rapida

TOUGHCUT

TOUGHCUT Diamond 400 Manuale utente

Yaros

Yaros PB-3603 Manuale utente

Fein

Fein BSS 2.0 E Guida all'installazione

Baileigh Industrial

Baileigh Industrial SS-2725 Manuale utente

Milwaukee

Milwaukee 2674-20 Manuale utente

Fein

Fein BLs 1.6 Manuale utente

Princess

Princess Electric Multi Sharpener Manuale utente

FOREDOM

FOREDOM K.1050 Manuale