Diagnostic Associates DA-Dongle J2534 Manuale utente

DA-Dongle J2534

User’s Manual

V3.2 06-10-14

Contents

Important Information 4

General Notice

Product Warranty

Terms & Conditions

Introduction 6

Getting to Know the Device 6

Installing the J2534 Device Drivers 8

Installing the DA App Hub 9

Updating the DA-Dongle J2534 Device 10

J2534 Device Driver Updating

DA-Dongle J2534 Software Updating

Device Recovery

Device Specification 11

Troubleshooting 12

Technical Support 13

Related Products 14

Important Information

General Notice

The DA–Dongle J2534 communication interface has been designed and tested to comply with

OBDII protocols. However, some vehicle models are not in full compliance with these protocols

for various reasons.

While Diagnostic Associates‟ testing and the experience of its many product users have shown

the unit to be safe and reliable, there is an inherent risk in using any product that may

potentially affect the operation or driveability of your vehicle.

If you are concerned about the operation of your vehicle at any time while using these products:

Pull off the roadway immediately or as soon as it is safe to do so.

Disconnect the device from the vehicle OBDII connector.

Consult your local car dealership or garage.

Report any issues or concerns to our Technical Support Team at

[email protected]. We are open Monday through Friday, 7:30 a.m. to 5:00

p.m. GMT, and all queries will be dealt with within a working day.

This User Manual is updated on a regular basis to ensure its content is up-to-date. Every effort

is made to ensure that the latest version is supplied with your product, however this is not

always practical. As a result you should always consult the Diagnostic Associates website to

determine if you have the latest version.

Product Warranty

Diagnostic Associates Limited guarantees that every DA-Dongle J2534 device is free from

physical defects in material and workmanship under normal use for twelve months from the date

of purchase.

Product Terms & Conditions

In no event shall Diagnostic Associates Limited‟s liability exceed the price paid for the product.

Diagnostic Associates shall be exempt from all other claims whether based upon direct, indirect,

special, incidental, or consequential damages resulting from the use of this product, its

accompanying software, or its documentation.

Diagnostic Associates Limited makes no warranty or representation, expressed, implied, or

statutory, with respect to its products or the contents or use of this documentation and all

accompanying software, and specifically disclaims its quality, performance, merchantability, or

fitness for any particular purpose. Diagnostic Associates Limited reserves the right to revise or

update its products, software, or documentation without obligation to notify any individual or

entity.

If you are not in agreement with these terms then you are advised to return the product, prior to

use, immediately for a full refund.

Please direct all enquiries to:

Diagnostic Associates Limited

Hyde Park House

Cartwright Street

Hyde

Cheshire

SK14 4EH

Introduction

Thank you for choosing the DA-Dongle J2534 device. This compliant SAE J2534 “Pass-Thru”

vehicle interface lets you use your PC to communicate and perform ECU diagnostics and

reprogramming on many modern vehicles.

The DA-Dongle J2534 device is a low-cost SAE J2534 compliant device. It provides a direct

connection to a laptop or desktop computer via a USB 2.0 full-speed connection (cable

supplied). All of the electronics are contained within the OBDII connector housing, making it a

compact and rugged vehicle communications tool.

The DA-Dongle J2534 can be powered by the USB connector, so there is no need to be

connected to the vehicle when updating the device software. However, a vehicle 12V supply on

pin 16 on the OBDII connector is required so that host PC applications will operate correctly

during normal operation.

Getting to Know the Device

Your package includes a DA-Dongle J2534 device, a USB 2.0 cable and this user guide. There is

no CD for the PC drivers and device update software, as up-to-date versions of these are

available from the Diagnostic Associates website at:

http://www.diagnostic-associates.com/download.htm

There are three main parts to the device and these are shown on the picture above.

Vehicle OBDII Connector : This is the end that connects to the vehicle OBDII diagnostic

connector and provides power to the device and connection to the vehicle communications

networks.

USB Connector : This connects the device to the PC via a USB (A-B) cable and is used to

control the device from the software application running on the PC.

LED Status Lights : These are used to give a visual indication to the user as to the state

of the device. There are 3 LEDs on the device that are repeated on both sides of the

device, these have the following functions.

PWR : This indicates that the device is powered up, either via the vehicle if connected

to the vehicle, or via USB if connected to a PC.

LNK : This indicates the state of the software within the device as well as indicates

the device status during reprogramming.

STS : This indicates the status of the device during its operation when connected to a

PC and its associated PC application. This LED has three colours, RED, GREEN and

AMBER.

Installing the J2534 Device Drivers

In order for the device to operate correctly with the target PC diagnostic application, you

will need to first install the DA-Dongle J2534 device drivers onto the PC that will control the

device. This can be done by following the procedure outlined below.

Note: The DA-Dongle J2534 supports Windows XP, Windows Vista (32 bit) and Windows 7

(32 bit).

It is important to install the DA J2534 Device Setup software before plugging your

DA-Dongle J2534 device into your computer.

Note: The following steps may differ slightly dependent upon the operating system or

components that are installed on your computer, but in general these are standard install steps.

1. Download the 'DA J2534 Device Setup Vx.x.zip' from:

http://www.diagnostic-associates.com/pages/downloads

The version number x.xx will be the latest available for the Diagnostic Associates

J2534 devices and must be used in conjunction with the appropriate software

loaded on the DA-Dongle J2534.

2. Unzip the files to a folder on the PC you want to use your DA-Dongle J2534 device with.

3. Double-click on the setup.exe file to begin the installation.

Note: If you do not have the .net Framework 4.0 on your PC this will be automatically

installed now. Similarly if you don't have the Visual C++ 2010 Runtime Libraries (x86)

installed you will be prompted to install these now also. When these have been installed

and completed the DA J2534 Software Setup Wizard installation will begin.

4. Choose a location to store the files. You may either leave the default installation

folder or choose your own and then confirm the installation. The DA J2534 software will

now install. During this part of the process two MS-DOS style windows will pop-up and

may remain on your screen for some time (even after the main installation application is at

the installation complete stage), this is perfectly normal. Do not attempt to close the MS-

DOS style windows manually as this will prevent the DA J2534 device drivers being

installed successfully, they will close automatically when the device driver install is

complete.

5. Plug your DA-Dongle J2534 device into your computer using the supplied USB cable. The

device will automatically be recognised by Windows and is now ready for use with your

chosen J2534 application.

Note: You should have no issues installing this software, however in the event that you

experience problems, then please contact the support desk via the website to assist you in

resolving your issue, once you have verified your issue.

Installing the DA App Hub

The DA App Hub is a PC based application that is installed on your PC which will allow you to

check for software updates to your DA-Dongle device, and to download them to your device

directly, via the USB cable.

The PC that this application is installed on should be connected to the internet as the installed

application will connect to the Diagnostic Associates file server to check for and download device

software updates.

Note: The DA App Hub is supported on Windows XP, Windows Vista (32 bit/64 bit) and

Windows 7 (32 bit/64 bit).

It is important to install the DA App Hub software before plugging your DA-Dongle

device into your computer.

Note: The following steps may differ slightly dependent upon the operating system or

components that are installed on your computer, but in general these are standard install steps.

1. Download the 'DAAppHub_Vx.x.x.zip' from:

http://www.diagnostic-associates.com/pages/downloads

The version number x.x.x will be the latest available for all the Diagnostic Associates

devices.

2. Unzip the files to a folder on the PC that will be used to update the device software.

3. Double-click on the setup.exe file, to begin the installation.

Note: If you do not have the Visual C++ 2010 Runtime Libraries (x86/x64) installed you

will be automatically prompted to install these now. When the Visual C++ 2010 installation

is complete the DA App Hub Setup Wizard installation will begin.

4. Choose a location to store the files. You may either leave the default installation

folder or choose your own and then confirm the installation. The DA App Hub will now

install.

5. A window will pop up asking if you wish to install the DA Device drivers - click „Yes‟ as this

is part of the installation process. Also, during this part of the process two MS-DOS style

windows will pop-up and may remain on your screen for some time (even after the main

installation application is at the installation complete stage), this is perfectly normal. Do

not attempt to close the MS-DOS style windows manually as this will prevent the DA

device drivers being installed successfully, they will close automatically when the device

driver install is complete.

6. Plug your DA-Dongle device into your computer using the supplied USB cable. The device

will automatically be recognised by Windows and is now ready for use.

7. Your DA App Hub is now ready for use, it can be run either from the Start Menu or the

Desktop short-cut.

Updating the DA-Dongle J2534 Device

Periodically Diagnostic Associates will release updates to its products drivers and software.

These updates are necessary to either release further device functionality, resolve any field

issues that have been highlighted, or to ensure that the devices are working correctly with OEM

software.

If you are experiencing any problems during device use, always make sure that you have the

latest device software and drivers.

J2534 Device Driver Updating

The latest version of the J2534 OEM device drivers can be located and downloaded from the

Diagnostic Associates website download page:

http://www.diagnostic-associates.com/pages/downloads

This can be downloaded by following the installation instructions on page 8 of this document.

Note: In conjunction with any J2534 Device Driver Updates, there will be a requirement to

update the software on the J2534 device itself, to the version associated with the Device Driver

Update. To do this, the following section should be followed.

DA-Dongle J2534 Software Updating

Note: An internet connection is required to update your DA-Dongle device as the software

automatically downloads the latest version of software from the Diagnostic Associates file server.

1. Connect your DA-Dongle to your PC using the supplied USB cable only.

Note: The device should NOT be connected to the vehicle when updating the device

software.

2. Run the DA App Hub using either the Start Menu or the Desktop short-cut.

3. The first „tab‟ of the application you see will be the Home tab. This contains information

about the status of your DA-Dongle software.

4. Selecting the „Update Applications‟ tab will allow you to update your DA-Dongle software as

follows.

5. Details of your DA-Dongle device will appear in the centre of the application

window. The information window at the bottom of the application will inform you if an

update is available or if your DA-Dongle is already up to date.

6. If an update is available you can click „Update Device‟ and the DA App Hub will update your

software to the latest level. When you click 'Update Device' the information box will display

the various stages required to update the software on your DA-Dongle. The progress bar

will also indicate progress through the various stages.

Indice

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente