DiaLFonZo-Copter V-Tail Hunter 400 Manuale utente
DiaLFonZo V-Tail
-
- /
FRAME REFERANCE ASSEMBLY GUIDE
info@dialfonzo-copter.com
Complied and rendered by InnerbreedFX
DiaLFonZo V-Tail
DiaLFonZo-Copter V-TAIL HUNTER 400/500 Assembly Guide (3/27/13)
Rev 1
Thank you for purchasing a DiaLFonZo-Copter frame from dialfonzo-copter.com.
There are a few different ways how to assemble your copter, but this assembly guide is
designed to iron out any potential problems you may have while assembling your
DiaLFonZo-Copter V-Tail HUNTER 400/500. We want you to feel comfortable while
building your frame, and by familiarizing yourself with the Frame Parts, you should have
an easier advantage. Identify all the parts and any potential miss-haps, (like that will
ever happen) during the manufacturing or packaging stage. Laying out the sections and
screws into groups will also help.
We are certain you will be happy with your new frame.
PARTS INCLUDED WITH YOUR KIT (Standard kit)
G10 PARTS:
x6 VTail–Arm Reinforcement
x1 VTail–Cross Brace
x2 VTail–Brace Support
x1 VTail–Centre Bottom
x1 VTail–Centre Protect (Optional)
x1 VTail–Centre Top
x2 VTail–Front Bottom Arm Plate
x2 VTail–Front Top Arm Plate
x6 VTail–Landing leg
x2 VTail–Rear Arm Plate
x2 VTail–Rear Bottom Motor Mount Plate
x2 VTail–Rear Top Motor Mount Plate
x2 VTail–V Part
HARDWARE: (Additional spares may be supplied)
31 x 0.5" standoffs
4 x 0.25" standoffs (To secure your flight controller)
56 x 1/4" 4-40 hex screws
14 x 5/16" 4-40 hex screws
14 x 4-40 nylon lock nuts
The assembly of your frame will start out by building some of the components needed
with the rest of the assembly later on. This way we insure you don’t then forget any
small details or forget something and have to go back and disassemble anything
DiaLFonZo V-Tail
Please follow the visual instructions carefully to make sure no mistakes are made.
ASSEMBLY of the Landing Legs (Build three of these)
The Landing legs are all identical and will be built the same way.
They are made up of four main G10 parts and associated hardware.
Note: You will be required to use four 5/16" 4-40 hex screws and four 4-40 nylon lock nuts for
each of the three assemblies.
ASSEMBLY of the Two Front Arms (Build two of these)
The Two Front Arms are all identical and will be built the same way.
They are made up of two main G10 parts and associated hardware.
+ One Pre made landing legs from the previous step.
Note:
As the 0.5" standoff in the landing leg is designed to pull the two landing tips closer
together, you may want to remove the 1/4" 4-40 hex screws from the 0.5" standoffs to make
installation into the frame much easier.
DiaLFonZo V-Tail
ASSEMBLY of the V-Tail & Rear Arm
The V-Tail assembly has two identical sides and will be built the same way. You will be
required to lock the Cross Brace using two 5/16" 4-40 hex screws and two 4-40 nylon lock
nuts.
DiaLFonZo V-Tail
The Rear Arm shares two identical plates, and will sandwich the Vtail part also encasing
the last Landing Leg built in previous steps, using G10 parts and associated hardware.
Note:
As the 0.5" standoff in the landing leg is designed to pull the two landing tips closer
together, you may want to remove the 1/4" 4-40 hex screws from the 0.5" standoffs to make
installation into the frame much easier.
DiaLFonZo V-Tail
ASSEMBLY of the Main Body
Finish the frame off by securing the three newly assembled parts using the top and
bottom centre plates and installing the last six remaining 0.5" standoffs and the 5/16" 4-40
hex screws.
Finished model with Optional Top Plate Finished model with Optional Canopy
DiaLFonZo V-Tail
PRE-FLIGHT CHECKLIST
Please check the condition of all the parts as they will get worn with age. Make sure you
also check the assembly of your frame, ensuring that all the screws and bolts are
securely fastened.
Ensure the propellers are secured properly (you don’t want them falling off during a
flight).
Ensure the receiver is receiving a strong signal and is secured in place.
Make sure the battery is secured tightly and will not slip out during flight.
Check that the motors and ESC are secured onto the frame and props spin smoothly.
Before take-off, make sure your transmitter channels are configured correctly and not
reversed.
This disclaimer is for any instructions published by DiaLFonZo-Copter. No warranty or
guarantee is provided for these instructions; you follow them at your own risk. No one at
dialfonzo-copter.com can vouch for their completeness or accuracy. If you are at all
uncomfortable or inexperienced working on your copters construction then please
These Instructions only picture the DiaLFonZo-Copter V-Tail 400 but can also be used
for the DiaLFonZo-Copter V-Tail 500 size range also.
info@dialfonzo-copter.com
Complied and rendered by InnerbreedFX
DiaLFonZo V-Tail
Questo manuale è adatto per i seguenti modelli
1
Indice
