Rebar or utility lines may be buried in concrete. Disconnect the power to
any utility lines. If these items are to be missed, clearly mark the area.
Loose objects could be thrown from crack. Make sure area to be cut is
clear from people and any loose objects, nuts, bolts, etc. Never run over
any loose objects.
Do not allow anyone to stand in line with the blade path. Do not let children
or visitors contact machine or extension cord. Keep children and visitors
away from the work area.
Diamond Cup Wheels produce heat and sparks during operation. Never
use machines in dangerous sites containing ammable, combustible or
explosive materials such as lacquer, paint, benzene, thinner, gasoline,
gases, and adhesive agents.
The cup wheel and shroud become hot during operation and remain hot
after stopped. Do not touch the cup wheel and shroud without proper hand
protection.
Keep a rm hold on the handle grips and maintain control of the machine
until the blade completely stops.
Never use a cracked, damaged, or misaligned cup wheel. After mounting
cup wheel rotate by hand to check for proper alignment.
Do not force a cup wheel onto the machine shaft or alter the size of the
arbor mounting hole. Never modify a cup wheel to t
Do not force a small grinder to do the job of a heavy-duty grinder. Do not
use the walk-behind grinder for improper applications. Never cut material
for which the blade was not designed.
The machine, cup wheels and tools should be stored in a dry and secure
location when not in use. Keep equipment out of reach of children.
The grinder will do the job better and safer at the rate for which it was
designed.
This includes primers, all coatings, adhesives, tile and crack lling materi-
als, etc. Do not attempt to cut, clean out or remove material without MSDS
information. Consult MSDS sheet for hazards information. Be aware that
some materials are explosive as a dust.
Keep proper footing and balance at all times.
Keep machine clean and follow maintenance procedures for better and
safer performance. Keep handles dry, clean, and free from oil and grease.
Follow instructions for lubricating and changing accessories.
INTRODUCTION
Thank you for purchasing a DIAMAPRO SYSTEMS® product. This manual
provides information and procedures to safely operate and maintain the
Speedi-Edge SU. For your own safety and protection from injury, carefully
read, understand, and observe the safety instructions described in this
manual. Keep this manual or a copy of it with the machine. If you lose this
manual or need an additional copy, please contact DiamaPro Systems®.
This machine is designed and built with user safety in mind; however, it
can present hazards if improperly operated and serviced.
Please follow the operating instructions carefully. If there are any questions
regarding operating or servicing of this machine, please contact
DiamaPro Systems®.
Disclaimer: DiamaPro Systems® and its aliates take no responsibility
for any damage, injury or death resulting from the incorrect or unsafe use
of this product. Use of this product should be undertaken by competent
persons only. It is the operator’s responsibility to ensure that the following
safety procedures are followed. If you are unsure, do not operate this
product.
1. SAFETY INSTRUCTIONS
1.1 KNOW THE RULES & YOUR EQUIPMENT
Most Job sites have rules governing equipment use & maintenance.
Before starting at a new work location, check with the supervisor or safety
coodinator. Ask about any rules or regulations you need to abide. OSHA
enforces federal laws within the United States that apply to the safe
operation, application, & maintenance of equipment on job sites. It is the
employer’s responsibility to comply with these laws.
Do not operate this machine unless you have read the operations and
maintenance manual carefully.
Do not operate this machine unless you have received operational and
maintenance training from a DiamaPro Systems® representative or from
an authorized distributor for DiamaPro Systems®.
Observe all applicable local, state and federal safety regulations. Wear
OSHA approved foot protection.
Observe all applicable local, state and federal safety regulations. Wear
OSHA approved safety glasses.
Breathable silica may be generated by use of this product. Silica can cause
severe and permanent lung damage, cancer, and other serious diseases.
Do not breath the dust. Do not rely on your sight or smell to determine if
the dust is in the air. Silica may be in the air without a visible dust cloud. If
air monitoring equipment for silica is not provided by your employer at your
work site, you MUST wear appropriate respiratory protection when using
or servicing the machine. Consult your employer and OSHA regarding the
appropriate respiratory protection.
Observe all applicable local, state and federal safety regulations. Wear
OSHA approved hearing protection.
Do not wear loose clothing or jewelry that can be caught in moving parts.
Wear protective hair covering to contain long hair. Keep hair away from
motor air vent. Rubber gloves and non-skid footwear are recommended
when working outdoors.
Do not expose machine to rain. Do not use machine in wet conditions.
Keep work area well lit. When working at an elevated location, pay atten-
tion to articles and persons below.
1.3 PROTECT YOUR FEET
1.4 PROTECT YOUR EYES
1.5 PROTECT YOUR LUNGS
1.6 PROTECT YOUR EARS
1.7 DRESS PROPERLY
1.8 AVOID A DANGEROUS ENVIRONMENT
1.9 BEWARE OF HIDDEN DANGERS IN
CONCRETE
1.10 KEEP WORK AREA CLEAN - DO NOT RUN
OVER ANYTHING
1.11 KEEP CHILDREN AND VISITORS AWAY
1.12 AVOID FLAMMABLE LIQUIDS OR GASES
1.13 AVOID CONTACT WITH HOT CUP WHEEL
AND SHROUD
1.14 KEEP FIRM GRIP ON MACHINE
1.15 CHECK CUP WHEEL FOR CRACKS,
DAMAGE, AND MISALIGNMENT
1.16 DO NOT FORCE WRONG SIZE OR TYPE CUP
WHEEL ON TO MACHINE
1.2 RECEIVE PROPER TRAINING
1.17 USE CORRECT EQUIPMENT AND
ACCESSORIES
1.18 STORE IDLE EQUIPMENT
1.19 DO NOT FORCE STAND-UP EDGER
1.20 OBTAIN MATERIAL SAFETY DATA SHEET
(MSDS) FOR ALL WORK SURFACE
MATERIALS
1.21 DO NOT OVERREACH
1.22 MAINTAIN MACHINE WITH CARE
