CALIFORNIA PROP 65 WARNING
Thank you for purchasing a DIAMAPRO®SYSTEMS product. This manual
provides information and procedures to safely operate and maintain the
DiamaPro®SVX2+A. For your own safety and protection from injury,
carefully read, understand, and observe the safety instructions described
in this manual. Keep this manual or a copy of it with the machine. If you
lose this manual or need an additional copy, please contact DiamaPro®
Systems. This machine is designed and built with user safety in mind;
however, it can present hazards if improperly operated and serviced.
Please follow the operating instructions carefully. If there are any ques-
tions regarding operating or servicing of this machine, please contact
DiamaPro®Systems.
Use of this product can cause exposure to materials known to the
State of California to cause
cancer and/or birth defects or other reproductive harm.
CALIFORNIA PROP 65 WARNING
DUST WARNING
Cutting, especially when DRY cutting, generates dust that
comes from the material being cut, which frequently contains
silica.
When dry cutting, be sure to use a HEPA ltered dust collector.
Silica is a basic component of sand, quartz, brick clay, granite and
numerous other minerals and rocks. Exposure to excessive amount
of such dust can cause:
n Respiratory diseases (aecting your ability to breath), including
chronic bronchitis, silicosis and pulmonary brosis from exposure
to silica. These diseases may be fatal;
nSkin irritation and rash; and
nCancer according to NTP* and IARC*
*National Toxicology Program, International Agency for Research
on Cancer
Take precautionary steps
nAvoid inhalation of and skin contact with dust, mist and fumes;
nWet cut when feasible, to minimize dust;
nWear and ensure that all bystanders wear appropriate respiratory
protection such as dust masks designed to lter out microscopic
particles. (See OSHA 29 CFR Part 1910.1200)
6. SAFETY PROVISIONS
• Carefully read the instructions in this manual before starting, using,
servicing or operating the vacuum cleaner
• Check that the vacuum cleaner hasn’t been damaged in any way
• Never turn on the machine if it is faulty or if you suspect it is faulty
• Check that the switch isn’t worn or damaged
• Do not approach the suction intake of the machine with unfastened or
broken garments that could easily be sucked into the machine
• Check that the lters are present and ecient
• Make sure that the lters are installed correctly and in full working order,
always observing the regulations in force in the workplace
• Do not carry out repairs without the manufacturer’s authorization
• Never use gasoline, solvents or other ammable liquids for cleaning;
only proper detergents should be used for cleaning
• Never move the machine by pulling the power cable or exible hose
• Never direct the opening of the machine or the exible tube towards
people or animals
• Protect the machine from the rain
• Check that the machine is connected to a power source with the correct
voltage indicated on the registration plate
• Make sure that the power cable has no wear or damage. If replacing
the cable, always replace it with another of the same specications as
the original one: cables that are not approved or of inferior quality may
overheat and cause serious injury to the user
• Make sure that the machine is connected to an appropriate power
source in full working order (check the presence of a fully functional
grounding socket)
• Repairs must only be carried out by authorized personnel and only
when the machine is turned o and disconnected from the power source
• Never allow unauthorized personnel to use the machine
• Make sure that all safety devices are in full working order before turning
on the machine
• Never cover the vacuum cleaner during use
7. INSTALLATION
7.1 DELIVERY AND HANDLING
All machines are carefully tested and checked by DiamaPro before deliv-
ery. The machine is transported inside a protective box or wrapped in a
protective lm that allows the courier to see the item during transport and
is securely xed to a pallet. If any part of the machine is not intact or has
been damaged during transport, le an immediate complaint with the cou-
rier. Parts that have been damaged or broken due to incorrect transport
or handling of the machine will not be recognized by the manufacturer’s
warranty. The machine must be lifted and moved using a forklift truck in
accordance with the relevant safety regulations in force in the workplace
7.2 CHECK THE PROPER ELECTRICAL
CONNECTION
Connect the industrial plug to the power cable and connect the plug to a
socket that has the same amp rating and is protected by a line-isolating
switch.
