Dick SM-100 Manuale utente

Friedr. Dick GmbH & Co. KG · Postfach 1173 · 73777 Deizisau · GERMANY ·

Tel.: +49 (0)7153-817-0 · Fax: +49 (0)7153-817-218/-219 · Web: www.dick.de · E-mail: [email protected] ·

No. 9 8070 3651 Vers. 3 / 11-2015

SM-100

1~230 V - 50 Hz

Operating Instructions (Translation)

Belt grinder

Art. No. 9 8070 000

Manufacturer and customer service address

Friedr. Dick GmbH & Co. KG

Postfach 1173

73777 Deizisau

GERMANY

These operating instructions are protected by copyright; all rights are reserved.

These operating instructions may not be reproduced or copied, either in full or

in part, without the prior consent of Friedr. Dick GmbH & Co. KG. Infringements

are subject to compensation claims and can result in criminal prosecution.

Be sure to visit the Friedr. Dick YouTube channel:

https://www.youtube.com/user/FriedrDick/videos

The videos demonstrate how to use Friedr. Dick machines.

Belt grinder SM-100 3

1. User Information .......................................................................................... 4

1.1 General.................................................................................................. 4

1.2 Symbols and conventions .....................................................................4

Instructions........................................................................................... 4

Lists...................................................................................................... 5

1.3 Symbols................................................................................................. 5

2. Scope of Supply .......................................................................................... 6

2.1 Package contents.................................................................................. 6

2.2 Unpacking the belt grinder .................................................................... 6

3. Product Liability .......................................................................................... 7

4. Environmental protection ........................................................................... 7

5. Safety............................................................................................................ 8

5.1 Meaning of the warnings ....................................................................... 8

5.2 Intended use..........................................................................................8

5.3 General safety instructions....................................................................9

5.4 Information signs on the belt grinder ................................................... 11

5.5 Covers ................................................................................................. 12

6. Structure and Function ............................................................................. 13

6.1 Technical data ..................................................................................... 13

6.2 Structure.............................................................................................. 14

6.3 Function...............................................................................................15

6.4 Covers ................................................................................................. 15

7. Putting into operation ............................................................................... 16

7.1 Installing the belt grinder ..................................................................... 16

7.2 Assembling the belt grinder................................................................. 17

7.3 Adjust belt grinder ............................................................................... 17

Adjusting the deflector plate............................................................... 18

Adjusting the grinding arm angle........................................................ 18

7.4 Install support foot ............................................................................... 19

7.5 Adjusting the belt alignment and running ............................................ 20

7.6 Controls on the belt grinder ................................................................. 21

7.7 Switching on the belt grinder ...............................................................22

7.8 Switching off the belt grinder ...............................................................24

8. Machining workpieces .............................................................................. 26

8.1 Grinding workpieces............................................................................ 26

Grinding zones ...................................................................................26

8.2 Polishing workpieces........................................................................... 29

9. Servicing and Maintenance ...................................................................... 30

9.1 Cleaning the belt grinder ..................................................................... 30

9.2 Changing the grinding belt .................................................................. 30

9.3 Changing the polishing wheel ............................................................. 32

10. Spare Parts................................................................................................. 34

10.1 Spare parts drawing ............................................................................ 34

10.2 Ordering spare parts ........................................................................... 35

11. EC Declaration of Conformity................................................................... 36

Belt grinder SM-100

User Information

1. User Information

1.1 General

These operating instructions are part of the SM-100 belt grinder

with the serial number given on the type plate (the type plate is

located on the back of the belt grinder).

The operating instructions must be kept close at hand at all times.

It contains important information and instructions for safe, proper

and economic use of the belt grinder. It must have been read and

understood by each person before this person can be entrusted

with the following work using the belt grinder:

• putting into operation,

•operating,

• servicing.

The operating instructions must be followed during all work on and

with the belt grinder. Following them helps to prevent hazards, to

reduce repair costs and to increase the reliability and life of the belt

grinder.

The technical information and instructions for use in these opera-

ting instructions are up-to-date and correct on delivery of the belt

grinder. Friedr. Dick GmbH & Co. KG reserves the right to further

develop the design and to make changes without notice.

All directional information is given from the view of the user.

1.2 Symbols and conventions

Instructions

Sequences of actions, which must be carried out in the given order

are given as a numbered list. Example:

1Instruction step 1.

2Instruction step 2.

Belt grinder SM-100 5

User Information

Lists

Lists without a particular order that has to be followed are shown

as a list with bullet points or indent markings. Example:

• Property A

- Detail 1

- Detail 2

• Property B

1.3 Symbols

Important or particularly useful information is highlighted by way of

symbols so that it is readily recognised.

WARNING

This symbol denotes a warning, which must always be noted and

followed.

• For more information on the meaning of the warnings, refer to

the Safety chapter.

MANDATORY

This symbol indicates instructions, which must be complied with

for safety reasons.

NOTE, TIP

This symbol denotes general information, which contains user

tips and useful information.

Belt grinder SM-100

Scope of Supply

2. Scope of Supply

2.1 Package contents

• Belt grinder

• Operating instructions

• Set of tools

• Polishing paste

2.2 Unpacking the belt grinder

Unpack the belt grinder immediately after purchase and check

whether it has any defects or transport damage. Also check the

package contents for complete scope of supply.

Report any defects immediately. Complaints made at a later date

can no longer be recognised.

Keep the invoice for the entire warranty period as proof of

purchase.

In case of complaints, write to Friedr. Dick GmbH & Co. KG, enc-

lose the original invoice and a precise description of the defect(s).

Before returning the product, wait for the manufacturer's reply in

order to initiate the necessary steps.

Friedr. Dick GmbH & Co. KG does not pay any transport costs for

returns that have not been explicitly approved.

Keep the original box for any necessary returns, in order to prevent

transport damage.

DAMAGE TO THE BELT GRINDER DUE TO INCORRECT CON-

NECTION DATA NOT IN LINE WITH THE SPECIFIED DATA

• Before starting up the belt grinder, compare the belt grinder's

electrical data (see “Technical data” on page 13) with the

connection data on site.

Belt grinder SM-100 7

Product Liability

3. Product Liability

DICK belt grinders are sold with a 12 month guarantee for the

owner, starting from the day of delivery (verification by means of

invoice).

All abrasives and other wearing parts are excluded from the guar-

antee.

Changes to the belt grinder require the manufacturer's prior written

approval.

Friedr. Dick GmbH & Co. KG does not accept any liability

whatsoever for defects or damage caused by incorrect assembly

or improper handling.

For further details of the guarantee, please refer to our General

Terms and Conditions of Sale, Delivery and Payment.

4. Environmental protection

Used machines, replacement parts and packaging are made of

recyclable materials. The owner is obliged to dispose of them

properly and in an environmentally friendly way, in accordance

with the legal regulations.

Belt grinder SM-100

Safety

5. Safety

5.1 Meaning of the warnings

In these operating instructions, a differentiation is made between

warnings depending on the hazard:

5.2 Intended use

DANGER

Imminent risk to life and the health of people.

• Causes serious injuries or death.

WARNING

Possibly imminent risk to the life and health of people.

• Could cause serious injuries or death.

CAUTION

Possibly dangerous situation

• Could cause minor injuries.

The SM-100 belt grinder is solely designed for commercial use.

The SM-100 belt grinder can be used for hand-guided dry grinding

(sharpening) and polishing of cleaned knives and cutting tools.

Any other or additional use is deemed to be not as intended and

therefore misuse.

The grinding of materials which produce harmful or readily ignita-

ble dusts is deemed to be misuse.

Belt grinder SM-100 9

Safety

5.3 General safety instructions

These include, for example:

•Aluminium

• Magnesium

The belt grinder may not be switched on or operated in potentially

explosive atmospheres and is solely designed for use in dry rooms

at temperatures between +3 and +30 °C.

Only original spare parts and accessories of Friedr. Dick GmbH &

Co. KG may be used.

The owner is responsible for any damage caused by misuse.

WARNING

Risk of injuries due to incorrect handling

Incorrect handling of the belt grinder can cause substantial inju-

ries.

• The belt grinder may only be used by people who have read

and understood the operating instructions.

• The belt grinder may only be operated by people who are

familiar with the putting into operation/starting up, operation,

and servicing of machines and the relevant accident preven-

tion regulations, who are able to recognise the hazards that

occur during the grinder's use and who work reliably.

• The belt grinder may not be operated outside the given power

ranges (see “Technical data” on page 13).

• Operate the belt grinder only for the approved uses (see

“Intended use” on page 8).

Belt grinder SM-100

Safety

WARNING

Risk of fire in the event of unsuitable environmental influ-

ences

Moisture (humidity) and water can cause a short circuit. Flying

sparks can cause flammable liquids and gases to ignite.

• Do not expose the belt grinder to rain or salt water.

• Do not use the belt grinder in a damp or wet environment.

• Ensure good lighting.

• Do not use the belt grinder near flammable liquids or gases.

Before each transport, switch off the belt grinder and remove the

mains plug from the socket.

Altri manuali per SM-100

Indice

Altri manuali Dick Macinacaffè

Dick

Dick SM-100 Manuale utente

Dick

Dick SM-200 Series Manuale utente

Dick

Dick SM-140 Manuale utente

Manuali Macinacaffè popolari di altre marche

Parkside

Parkside PWS 230 C3 Manuale utente

SUHNER ABRASIVE

SUHNER ABRASIVE ASC 9 Manuale tecnico

PTA

PTA P1322 Manuale utente

Crown

Crown CT13313 Manuale utente

Parkside

Parkside 280250 Manuale utente

Climax

Climax VM2150 Series Manuale utente

Jet

Jet JPSG-618M1 Manuale di servizio

Makita

Makita GA4030 Manuale utente

DeWalt

DeWalt DWEN202 Manuale utente

Grizzly

Grizzly G2790 Manuale utente

Fein

Fein MSf843-1a Manuale utente

Bosch

Bosch GWS 14,4 V PROFESSIONAL Manuale utente

RAMSET

RAMSET CBAGR18 Manuale utente

Bosch

Bosch 8-115 Z Manuale utente

STEELE PRODUCTS

STEELE PRODUCTS SP-PB008 Manuale utente

MW TOOLS

MW TOOLS ME15W Manuale utente

Caravaggi

Caravaggi SP 20 Istruzioni operative

SUHNER ABRASIVE

SUHNER ABRASIVE UWK 10-R125 Manuale tecnico