Digilock Curve Keypad Basic Manuale utente

INSTALL GUIDE
Keypad & RFID | Basic & Advanced
1
Deadlatch |Motorized Rear Deadbolt |Motorized Rear
Keypad
RFID

INSTALL GUIDE
Keypad & RFID |Basic & Advanced
2
Wood Door Preparation
Required Components ����������������������������������������������������������������������������������������������������������������������������������������������������������3
Required Tools & Materials����������������������������������������������������������������������������������������������������������������������������������������������������3
Strike Installation Steps���������������������������������������������������������������������������������������������������������������������������������������������������������4
Wood Door Drill Instructions �������������������������������������������������������������������������������������������������������������������������������������������������5
Hole Mounting Template�������������������������������������������������������������������������������������������������������������������������������������������������������5
Metal Door Preparation
Compatibility Guide ��������������������������������������������������������������������������������������������������������������������������������������������������������������6
Required Tools & Materials����������������������������������������������������������������������������������������������������������������������������������������������������6
Removal of 3-hole Lock Plug �������������������������������������������������������������������������������������������������������������������������������������������������6
Removal of Padlock Hasp ������������������������������������������������������������������������������������������������������������������������������������������������������6
Nut Post - Cable Connector Installation
For door thickness measuring between 0�16” - 0�91” [4mm - 23mm]
Required Components ����������������������������������������������������������������������������������������������������������������������������������������������������������7
QR Code Sticker Placement ���������������������������������������������������������������������������������������������������������������������������������������������������7
Lock Installation Steps��������������������������������������������������������������������������������������������������������������������������������������������������������8-9
Lock Testing����������������������������������������������������������������������������������������������������������������������������������������������������������������������������9
Screw Post - Pin Connector Installation
For door thickness measuring between 0�01” - 0�16” [0�2mm - 4mm]
Required Components ��������������������������������������������������������������������������������������������������������������������������������������������������������10
QR Code Sticker Placement �������������������������������������������������������������������������������������������������������������������������������������������������10
Lock Installation Steps��������������������������������������������������������������������������������������������������������������������������������������������������� 11-12
Lock Testing��������������������������������������������������������������������������������������������������������������������������������������������������������������������������12
TABLE OF CONTENTS

INSTALL GUIDE
Keypad & RFID |Basic & Advanced
3
Security Strike Plate
Recommended for latch products
Angled Strike Plate
General Purposes Use
Double-Door Strike Plate
Requires a base latch on strike door (Not included)
This section is for new installations with wood, MDF, or non-metal doors�
REQUIRED COMPONENTS
1 - Phillips Driver (#1)* 1 - Phillips Driver (#2)*
1 - Power Drill*
1 - Pencil*
1 - ¹/6" Wood Drill bit*
Removable Tape*
1 - ³/32" Wood Drill bit*
1 - Ruler*
1 - ³/4" Wood Drill bit*
Recommended Forstner Bit
Recommended 90º Square
Recommended Brad Point BitRecommended Brad Point Bit
Note: Mounting hardware requires a torque level of: 21.4 kgf/cm² ±20% for hand or powered tools to insure proper lock functionality.
WOOD DOOR PREPARATION
REQUIRED TOOLS & MATERIALS

INSTALL GUIDE
Keypad & RFID |Basic & Advanced
4
Door Frame
0.32 in
[8mm]
Mark Here
Door Frame
Drill Pilot
Holes Here
Door Frame
0.32 in
(8 mm)
Door Frame
0.32 in
[8mm]
Mark Here
Door Frame
Door Frame
Shown below Angled Strike Plate
Position the strike plate on the door frame aligning it with the
center of the lock’s mounting holes.
" drill bit.
Adjust the strike plate to the proper position 0.32" [8 mm]
from the door edge then tighten the self tapping screws.
Insert and tighten the remaining self tapping screw into the
center opening to secure strike position.
Allow 0.32" [8 mm] from door edge and mark the position of
the adjustment slot holes.
Position the strike plate and the self tapping screws into the
adjustment slot holes. Do not tighten the screws.
1
3
5
2
4
6
STRIKE INSTALLATION STEPS

INSTALL GUIDE
Keypad & RFID |Basic & Advanced
5
(a)
(b)
(b)
(a)
Drill x2
5/16" 0.3125in
[7.94 mm]
Drill 3/4"
0.75in [19mm]
Strike Center
(a)
(b)
0.31”
[7.94mm]
0.31”
[7.94mm]
0.75”
[19mm]
1.09”
[27.75mm]
1.09”
[27.75mm]
2.19”
[55.5mm]
CENTER LINE
CENTER LINE
ALIGN EDGE OF
STRIKE PLATE HERE
FOR LEFT
CLOSING DOOR
ALIGN EDGE OF
STRIKE PLATE HERE
FOR RIGHT
CLOSING DOOR
ALIGN EDGE OF
STRIKE PLATE HERE
FOR LEFT
CLOSING DOOR
ALIGN EDGE OF
STRIKE PLATE HERE
FOR RIGHT
CLOSING DOOR
0.92”
[23.4mm]
0.92”
[23.4mm]
Door Mounting Holes Drill Instruction and Template
With the door open place the Template over the locker frame.
(a) Align the edge of Strike Plate with the Strike Plate Marker.
(b) Center the Template to the center of the Strike Plate.
You may secure the Template with removable tape.
Close the door over the Template.
(a) Mark the door edge at the Template Center Line.
(b) Mark the Template with the edge of the door.
1 2
Place the Template on the front of the door.
(a) Align the drawn mark on the Template with the door edge.
(b) Center the Template with the mark on the door.
Secure the Template with removable tape.
Mark the center points of the door mounting holes on the
front of the door. Drill the holes according to the specified
dimensions.
3 4
Cut along the dashed lines for New Doors or Drawers
Before printing, turn off auto scaling or “Fit to Paper” in your printer setup and print at 100%
WOOD DOOR DRILLING INSTRUCTIONS
HOLE MOUNTING TEMPLATE

INSTALL GUIDE
Keypad & RFID |Basic & Advanced
6
Digilock is compatible with a majority of 3-hole configuration, latch, and handle door types. Some doors may require modification to
clear obstructions.
Types of Metal Box Locker Doors
Single Point Latch HandleStandard Lift Box Locker Padlock Hasp
Hasp Removal Steps
Plug Removal
Close the door and mark the
area to cut the padlock hasp.
Open the door then cut the
padlock hasp on the marked
cut line.
Smooth out rough or sharp
edges.
1 3
1 2
2
Required Tools *Not Included
Hack Saw* Metal File* Screw Driver* Adjustable
Wrench*
See Hasp removal steps
METAL DOOR PREPARATION

INSTALL GUIDE
Keypad & RFID |Basic & Advanced
7
For door thickness measuring between 0�16” - 0�91” [4mm - 23mm]
Required Components
Front Unit Rear Unit
RFID Standard BodyKeypad Standard Body Deadbolt - Cable Deadlatch - Cable
1*- Phillips Head Screwdriver (#2)2 - Split Lock Washers 2 - #10-24 Pan-Head Phillips Screws
D
C
B
A
Screw
Size Length
Door Thickness
Min Max
A 5/8" [15.875 mm] 0.01" [0.2 mm] 0.16" [4 mm]
B 7/8" [22.225 mm] 0.16" [4 mm] 0.43" [11 mm]
C 1 1/8" [28.575 mm] 0.43" [11 mm] 0.67" (17 mm]
D 1 3/8" [34.925 mm] 0.67" [17 mm] 0.91" [23 mm]
* Not Included
Note: Mounting hardware requires a torque level of: 21.4 kgf/cm² ±20% for hand or powered tools to insure proper lock functionality.
For illustration, a keypad front unit with a bolt rear unit is shown�
Rear View Front View
1
With the rear unit behind the door, extend the ribbon cable through the doors center opening.
Cable Connector
Orientation
NUT POST - CABLE CONNECTOR INSTALLATION
LOCK INSTALLATION STEPS (1-6)

INSTALL GUIDE
Keypad & RFID |Basic & Advanced
8
Front View
2 3
4 5
Rear View
ATTENTION: The rear-unit connector must be oriented with the red wire positioned on the top of the
ribbon cable (as highlighted in g-1). Improper connection may result in the lock to improperly function.
With the cable connector properly oriented. Insert the rear units
cable connector to the corresponding front units pin-connector
(as highlighted in fig-1).
The LED will flash red 3 times accompanied with a three-tone
beep, then followed by the LED flashing green 3 times.
Note: The audible/visual feedback may only indicate that the
metal pin's have made contact. It is necessary to further insure
that both connectors are properly seated and connected
(as highlighted in fig-2).
For illustration, a keypad front unit with a bolt rear unit is shown�
Insert the front units nut-post through the doors mounting holes.
Hold and align the rear-unit using the same mounting holes
Note: To avoid pinching of the ribbon cable a recessed pocket is
provided behind the rear unit.
Insert the screw with lock-washer through the mounting holes.
Tighten screws to the torque level of: 21.4 kgf/cm² ±20%
Note: Overtightening of the mounting hardware may result in
the lock to improperly function.
Use the screw chart
to select the proper
screw length for your
door thickness.
Rear View
6
Front View
Test the lock while the door is open to ensure that the bolt or latch is operating properly. Refer to the testing instructions below.
Once installation is complete, refer to the DigiLink Site Setup Guide to add locks.
fig-1 fig-2
LOCK INSTALLATION STEPS

INSTALL GUIDE
Keypad & RFID |Basic & Advanced
9
RFID
CARD
RFID
CARD
To ensure functionality after installation, it is recommended that the lock is tested with the door open�
Repeat test with the door closed.
If ten rapid beeps are heard, the strike plate or door alignment may need adjustment to allow the lock to operate properly.
If the door does not lock when the bolt/latch is extended, the strike plate or lock position may need adjustment.
Press = ` to extend the bolt.
Press = ` again to retract the bolt.
Press = ` to retract the latch.
The latch will extend automatically.
Present any RFID card to reader to extend the bolt.
Present the same RFID card to reader again to retract the bolt.
Present any RFID card to reader to retract the latch.
The latch will extend automatically.
For touch-free RFID locks with deadbolt rear units:
For touch-free RFID locks with deadlatch rear units:For keypad locks with deadlatch rear units:
For keypad locks with deadbolt rear units:
LOCK TESTING INSTRUCTIONS

INSTALL GUIDE
Keypad & RFID |Basic & Advanced
10
For door thickness measuring between 0�01” - 0�16” [0�2mm - 4mm]
2 - Locking Nuts 1*- Deep Socket Nut Driver [3/8”]
* Not Included
For illustration, a keypad front unit with a bolt rear unit is shown�
Note: Mounting hardware requires a torque level of: 21.4 kgf/cm² ±20% for hand or powered tools to insure proper lock functionality.
Required Components
Front Unit
RFID Standard BodyKeypad Standard Body
Rear Unit
Deadbolt - Pin Deadlatch - Pin
Rear View Front View
1
Insert the front unit screw posts through the doors mounting holes.
Cable Connector
Orientation
SCREW POST - PIN CONNECTOR INSTALLATION
LOCK INSTALLATION STEPS (1-4)
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali Digilock Sistema RFID


















