Technical Support
Phone: (248) 236-0061, Mon.-Fri., 9:30am-5:30pm
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note 1: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. f this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: a) Reorient or relocate the receiving antenna
b) ncrease the separation between the equipment and receiver c) Connect the equipment into an outlet on
a circuit different from that to which the receiver is connected d) Consult the dealer or an experienced
radio/TV technician for help.
Note 2: Any changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
BEF RE FIRST USE
Your PowerNow! 15600 comes from the factory with a charge and can be used
right out of the box. However, it is best to make sure that the unit is fully charged
before first use. Press the Power Button to see how much charge is in the unit.
The Battery Status LEDs light up to show the charge level. The Battery Status
LEDs will turn off after a few seconds.
• One LED Lit: 25% Charged • Two LEDs Lit: 50% Charged
• Three LEDs Lit: 75% Charged • Four LEDs Lit: 100% Charged
Charging the PowerNow! 15600™
To charge the PowerNow! 15600, insert the Micro USB end of the included USB
to Micro-USB/Apple®30-pin/Apple 8-pin Charging Cable into the power
bank’s Micro-USB Power Input Port and the other end into a USB Port on your
computer or the included USB wall adapter. The Battery Status LEDs light up
to indicate the current power level. All four lights glow steadily when the unit is
fully charged.
Charging a Smartphone, Camera, or ther Device
To charge a smartphone or similar device with the PowerNow! 15600, plug the
device into either of the USB Power utput Ports and press the n/ ff
Button. The Battery Status LEDs light up, showing the percent of power
remaining in the PowerNow! 15600. When the device is fully charged, the
Battery Status LEDs turn off. You may charge two smartphones (or similar
devices) at one time by plugging one into each USB Power utput Ports.
1.0 Amp USB
Power utput Port
n/ ff
Button
2.1 Amp USB
Power utput Port
Charging a Tablet
To charge a tablet with the PowerNow! 15600, plug the device into the
2.1 Amp USB Power utput Port and press the n/ ff Button. The Battery
Status LEDs light up, showing the percent of power remaining in the PowerNow!
15600. When the device is fully charged, the Battery Status LEDs turn off. You
may charge a tablet and a smartphone (or similar device), at the same time, as
long as the tablet is plugged into the 2.1 Amp USB Power utput Port.
IMPORTANT:
If you plug the tablet into the 1.0 Amp USB Power utput
Port, it MAY N T CHARGE. The 1.0 Amp USB Power utput Port does not
provide strong enough power output to charge most tablets.
Using the LED Flashlight
To activate the LED Flashlight, press the n/ ff Button two times. Press the
n/ ff Button two more times to turn the LED Flashlight off.
Troubleshooting
The PowerNow! 15600 Will Not Charge - Check to make sure that the USB to
Micro-USB/Apple®30-pin/Apple 8-pin Charging Cable is properly connected
to the Micro USB Power Input Port. f the unit still will not charge, your power
cable may be damaged. Connect the unit using a different power cable.
A Smartphone Will Not Charge - Check to make sure that the smartphone
is securely connected and the PowerNow! 15600 is charged. Recharge the
PowerNow! 15600 if necessary. f the smartphone still will not charge, your power
cable may be damaged. Connect the smartphone using a different power cable.
A Tablet Will Not Charge - Check to make sure that the tablet is securely
connected to the 2.1 Amp USB Power utput Port. The 1.0 Amp USB Power
utput Port does not have a strong enough power output to charge most tablets.
f another device is plugged into the 1.0 Amp USB Power utput Port while the
tablet is plugged into the 2.1 Amp USB Power utput Port, unplug it. One of
the devices may be drawing too much power for two devices to be charged at
the same time. Make sure that the PowerNow! 15600 is charged. Recharge the
PowerNow! 15600 if necessary. f the tablet still will not charge, your power
cable may be damaged. Connect the tablet using a different power cable.
CAUTI N:
Store the PowerNow! 15600 in a cool, dry place. Avoid water and corrosive
chemicals. Do not violently shake or strike. Device contains no user-serviceable
parts. Do not disassemble. f the device is overheating or smoking or if the case
is damaged, deformed, or discolored, immediately discontinue use.
How to Properly Dispose of Batteries
This product contains lithium-ion batteries. To properly dispose of expired
batteries, view your city’s website or newsletter to find what guidelines, if any,
should be followed and to make note of their hazardous waste collection days.
Micro USB
Power Input Port
