Digitalview HD-3000 Manuale utente

Specifications subject to change without notice

1 of 15

HD/SD-SDI to HDMI adaptor board

HD-3000

Manual

Specifications subject to change without notice

2 of 15

Table of Contents

Introduction

Connectors, Pin outs &

Ju pers

Board Di ensions

Signal Support Mode

Table

Specification

Warranty, Caution &

Li itation of Liability,

Trade arks

Contact details

Revision History

Specifications subject to change without notice

3 of 15

1. Introduction

The HD-3000 converts SD/HD-SDI (SD, HD and 3G) signa to HDMI for driving HDMI monitors. The HD-3000 provides re-c ocked oop

through outputs for “daisy chaining” mu tip e monitors or other equipments to the same HD-SDI source. It a so supports embedded

audio.

Fu y comp iant with the SMPTE 259M-C, SMPTE 292M, SMPTE 424M, 425M standards.

HD-3000 Key Features

a. Supports 1.5Gbits & 3Gbits bit rate input signal support.

The mode support is isted in page 11.

b. Dual channels input port supported.

HD-3000 supports Path A (HD-SDI input from J1 port convert to output HDMI at HDMI1/HDMI1A port) and Path B (HD-SDI input

from J2 port convert to output HDMI at HDMI2/HDMI2A port). See Figure be ow :

c. HD-SDI re-clock loop through output.

J1 HD-SDI input and re-c ock oop through to J3 HD-SDI output. J2 HD-SDI input and re-c ock oop through to J4 HD-SDI output.

d. HDMI (v1.3) x 2 output port.

Two HDMI output ports are HDMI1/HDMI1A, HDMI2/HDMI2A.

e. Stereo e bedded audio support

f. On-board power on/off switch – The power on/off switch is insta ed on SW1.

Specifications subject to change without notice

4 of 15

g. Status LEDs on board :

The definition of the LED1, LED2, LED3, LED4 are :

Ref Description

LED1 / LED2 Green LED on : Signa detected

Green LED B inking : No signa detected

LED3 / LED 4 Green LED on : Signa output

Green LED off : No signa output

Specifications subject to change without notice

5 of 15

2. CONNECTORS, PINOUTS & JUMPERS

The various connectors are:

Su ary: Connectors

Ref Description Type / Use

J1 SD/HD-SDI 1 Input BNC connector

J2 SD/HD-SDI 2 Input BNC connector

J3 SD/HD-SDI 1 re-c ock oop through output BNC connector

J4 SD/HD-SDI 2 re-c ock oop through output BNC connector

CN1 RS-232 & I

C contro connector JST 6-way, B6B-XH-A (Matching type : XHP-6)

CN2 Reserved for programming use Reserved

CN3 Reserved for programming use Reserved

CN4 Externa I/O connector Hirose DF13-6P-1.25DSA

(Matching type : Hirose DF13-8S-1.25C)

CN5 Reserved for programming use Reserved

HDMI1 HDMI 1 Output HDMI connector

Specifications subject to change without notice

6 of 15

Ref Description Type / Use

HDMI2 HDMI 2 Output HDMI connector

HDMI1A A ternate HDMI 1 Output JST BM20B-SRDS (Matching type : JST SHDR-20V-S-B)

HDMI2A A ternate HDMI 2 Output JST BM20B-SRDS (Matching type : JST SHDR-20V-S-B)

PP1 Power Input (A ternate) Mo ex 43650-0200 compatib e

(Matching connector type : Mo ex 43645-

0200 compatib e)

(Matching power cab e : P/N 426013800-3)

PP3 Power Input DC power jack, 2.5mm contact pin diameter positive

S1 A ternate power on/off switch connector JST B2B-XH-A (Matching type : XHP-2)

SW1 Power on/off s ide switch S ide switch

SW3 No function Reserved

Su ary: Ju per settings :

Ref Purpose Note

JA1 On board +5V ogic power enab e 1-2 & 3-4 c osed, factory set, do not remove

LED1A Externa LED connection Refer to pin assignment in page 7

LED2A Externa LED connection Refer to pin assignment in page 7

LED3A Externa LED connection Refer to pin assignment in page 7

LED4A Externa LED connection Refer to pin assignment in page 7

JP1-12 No function No function

JP13 Reserved for programming use Reserved

JP14 Reserved for programming use Reserved

SW2 No function No function

Specifications subject to change without notice

7 of 15

Su ary : PinOuts :

CN1 – RS-232 & I

C control : JST B6B-XH-A (Matching type : XHP-6)

PIN SYMBOL DESCRIPTION

1 SCLK I2C_SCLK

2 SDATA I2C_SDATA

3 VCC +5V

4 TXD RS-232 Tx data

5 GND Ground

6 RXD RS-232 Rx data

CN4 – External I/O connector : Hirose DF13-6P-1.25DSA (Matching type : Hirose DF13-8S-1.25C)

PIN SYMBOL DESCRIPTION

1 3V3 3.3V output

2 LED3 LED3 Anode

3 LED4 LED4 Anode

EXT_IP_0

Reserved

EXT_IP_1

Reserved

6 LED1 LED1 Anode

7 LED2 LED2 Anode

8 GND LED Cathode

LED1A, LED2A, LED3A, LED4A – External LED connection

PIN SYMBOL DESCRIPTION

1 + LED Anode

2 - LED Cathode

HDMI1A – Alternate HDMI connector: JST BM20B-SRDS (Matching type : JST SHDR-20V-S-B)

PIN SYMBOL DESCRIPTION

1 GND Ground

GND

Ground

3 RXC+ TMDS Data C+

Specifications subject to change without notice

8 of 15

PIN SYMBOL DESCRIPTION

4 RXC- TMDS Data C-

5 RX0+ TMDS Data 0+

6 RX0- TMDS Data 0-

7 RX1+ TMDS Data 1+

8 RX1- TMDS Data 1-

9 RX2+ TMDS Data 2+

10 RX2- TMDS Data 2-

GND

Ground

12 GND Ground

13 MSTR2_SCL Reserved

14 MSTR2_SDA Reserved

15 DDC_5V +5V power supp y for DDC (optiona )

16 HPD Hot p ug detection

17 DDC_SCL DDC seria c ock

18 DDC_SDA DDC Data

19 VCC1 VCC 5V output

20 VCC2 VCC 5V output

HDMI2A – Alternate HDMI connector: JST BM20B-SRDS (Matching type : JST SHDR-20V-S-B)

PIN SYMBOL DESCRIPTION

1 GND Ground

2 GND Ground

3 RXC+ TMDS Data C+

4 RXC- TMDS Data C-

5 RX0+ TMDS Data 0+

6 RX0- TMDS Data 0-

7 RX1+ TMDS Data 1+

8 RX1- TMDS Data 1-

9 RX2+ TMDS Data 2+

Specifications subject to change without notice

9 of 15

PIN SYMBOL DESCRIPTION

10 RX2- TMDS Data 2-

11 GND Ground

12 GND Ground

13 MSTR2_SCL Reserved

14 MSTR2_SDA Reserved

15 DDC_5V +5V power supp y for DDC (optiona )

16 HPD Hot p ug detection

DDC_SCL

DDC seria c ock

18 DDC_SDA DDC Data

19 VCC1 VCC 5V output

20 VCC2 VCC 5V output

S1 – Alternate power on/off switch connector (Matching type : XHP-2)

PIN SYMBOL DESCRIPTION

1 12V_IN +12V INPUT

12V_OUT

+12V OUTPUT

PP1 – Alternate 12VDC power supply

PIN DESCRIPTION

1 +12VDC in

2 Ground

PP3 - 12VDC power supply

PIN DESCRIPTION

1 +12VDC in

Ground

Specifications subject to change without notice

10 of 15

3. BOARD DIMENSIONS

Ready- ade 3D Pro-E (SLDPRT) drawing files - Save time and effort for your system vo umetric ana ysis design.

Inc udes jpg fi e previews. P ease go to down oad at http://www.digita view.com/accessories/hd-3000

The maximum thickness of the adaptor board is 18mm (measured from bottom of PCB to top of components, exc uding the

BNC connectors. We recommend c earances of:

• 5mm from bottom of PCB - if mounting on a meta p ate we a so recommend a ayer of suitab e insu ation materia is

added to the mounting p ate surface.

• 10mm above the components

• 3~5mm around the edges

Any of the ho es shown above can be used for mounting the PCB, they are 3.2mm in diameter.

CAUTION: Ensure adequate insulation is provided for all areas of the PCB with special attention to high voltage parts

such as the inverter.

Indice

Manuali Adattatore popolari di altre marche

PCB Piezotronics

PCB Piezotronics 090B274 Manuale utente

Auvidea

Auvidea J20 Manuale del prodotto

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manuale utente

Akribis

Akribis ITF-21-BISS-MIT Manuale utente

Tenda

Tenda W54U Manuale utente

ROHO

ROHO AGILITY Manuale utente

PROLiNK

PROLiNK WN2001 Manuale utente

Hawking

Hawking HUF2 Manuale utente

Airlink101

Airlink101 AWLC4030 Manuale utente

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manuale utente

Philips

Philips SWA4554S/10 Manuale utente

JVC

JVC TS-C9D2B Manuale di istruzioni

NETGEAR

NETGEAR A6100 Manuale utente

D-Link

D-Link DWA-121 Manuale utente

Philips

Philips SWA2037 Manuale utente

Basalte

Basalte 0610-20 Manuale utente

Yealink

Yealink EHS40 Manuale utente

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manuale utente

digitalview HD-3000 Manuale utente

Manuali Adattatore popolari di altre marche