Digitools DigiDirve-4 Series Manuale utente

User Manual

DigiDirve-4.x

Document version: 20210822

Decoder software version 23 or higher

DigiDrive-4.1

DigiDrive-4.2

DigiDrive-4.5

Content

Főbb paraméterek: ..................................................... Hiba! A könyvjelző nem létezik.

A v23-as működtető szoftver általános jellemzői: ........................................................ 5

Bekötés:....................................................................... Hiba! A könyvjelző nem létezik.

DigiDrive-x.1: ............................................................................................................. 7

DigiDrive-x.2: ............................................................................................................. 8

DigiDrive-x.3: ............................................................................................................. 8

DigiDrive-x.5: ............................................................................................................. 9

Üzembe helyezés: ....................................................... Hiba! A könyvjelző nem létezik.

Motorvezérlő kimenet: ............................................ Hiba! A könyvjelző nem létezik.

A terhelés szabályzó beállítása: ............................... Hiba! A könyvjelző nem létezik.

Mozdony sebesség beállítása: .................................... Hiba! A könyvjelző nem létezik.

A 3 pontos sebesség görbe (CV29,4=0): .................. Hiba! A könyvjelző nem létezik.

A 28 pontos sebesség görbe (CV29,4=1): ................ Hiba! A könyvjelző nem létezik.

Sebesség alapjel szorzó: .......................................... Hiba! A könyvjelző nem létezik.

Gyorsítás lassítás beállítása: .................................... Hiba! A könyvjelző nem létezik.

Funkció kimenetek: ..................................................... Hiba! A könyvjelző nem létezik.

Funkció kimenetek regiszterei: ................................ Hiba! A könyvjelző nem létezik.

Funkciókimenet üzemmódjának és az alap „fényerő”-nek a beállítása: ................ 18

Egyéb funkciók: ........................................................... Hiba! A könyvjelző nem létezik.

Analóg mód: ............................................................. Hiba! A könyvjelző nem létezik.

Működés fékgenerátorral vezérelt szakaszon. ........................................................ 27

ABC mód: ................................................................................................................. 28

RailCom: ................................................................................................................... 30

Többmozdonyos üzem (consist mód): .................... Hiba! A könyvjelző nem létezik.

Szétcsatolás funkció: ............................................... Hiba! A könyvjelző nem létezik.

SUSI interfész: .......................................................... Hiba! A könyvjelző nem létezik.

Funkciógomb állapotának mentése: ....................... Hiba! A könyvjelző nem létezik.

Nehéz vonat funkció: ............................................... Hiba! A könyvjelző nem létezik.

Konfig regiszterek CV29, CV49: ............................................................................... 37

Programozás: .............................................................................................................. 38

ACK impulzus: .......................................................... Hiba! A könyvjelző nem létezik.

CV regiszterek alap állapotának visszaállítása, mentése: ..... Hiba! A könyvjelző nem

létezik.

A funkció gombok alap beállítása: ........................... Hiba! A könyvjelző nem létezik.

CV regiszterek: ............................................................................................................ 40

Thank you for choosing the product developed and produced by

the Hungarian DigiTools Electronics Ltd.

Key features:

o Communication according to NMRA DCC standard

o speed gear of 28, 128, programmable speed curve

o Addressed between 1-9999

o Max. 1 A motor output

o Load control (can be set in CV register)

o 18 kHz motor PWM frequency

o 4 pcs. (NEM651-652) or 10 pcs. (plux22) short circuit protected interface

(altigether max. 700 mA)

o Analogue mode

o Assymmetric DCC sign notice (ABC mode)

o Constant break path in ABC mode

o RailCom

o SUSI interface (only plux22)

o Consist (multitrain) mode

o Handling FL, F1-F28 functions

o Dimming function

o Shunting mode

o Switching on and off acceleration, deccelereation

o Driving function

o Car disconnection function

o 3 or 28 point speed curve setting

o o Different interfaces for the different standards

o Sizes:

▪ 10.5 * 16.5 * 4 mm (NEM651, NEM652)

▪ 15 * 18 * 4 mm (NEM658 PLUX22)

Overall features of v23 softvare:

The software of DigiDrive decoder family gained those functions that were

developed in DigiSound5 sound decoder. The new firmware can only be uploaded to

those DigiDrive softwars that are present in the market from 2015.

Changes in v23 version compared to v21 version:

- Standardizing the numbers and functions of CV registers.

- New function outputs and modes.

- Rewriting motor measuring.

- Rewriting PID regulator.

- Fault corrections.

It is essential if we update our decoder from earlier than v23 version it is necessary

to reset it before using it (CV8=0)!

It is banned to call back the saved CV settings!

Installing the Decoder:

Before installing the decoder it is reccommened to do as follows:

o if you are digitalizing your existing analogue system check if there is an

inte-grated buffer capacitor remained on the rail!

o o when digitalizing old, not prepared locomotives it is essential to

check if the value of the buffering capacitor is not higher than 47nF. If

there is no reactor coil between the motor and the decoder, do not leave

the capacitor on the output of the motor. Remove any capacitor

between the two motor leads and the frame,

o clean all the current collector skates and the wheels of the locomotive,

o run the motor starting from ~5-10V in neutral gear, while measuring the

cur-rent consumption. If it takes more than 200mA, check the state of

the motor brush and the commutator and if necessary sweep out the

coal powder from the gaps between the bites,

o check the light bulbs, if necessary change them into higher voltage ones.

The new bulbs should have at least 16V,

o check the insulations. In case of locomotives, where one of the poles of

the rail is the metal body itself it is important to check if the motor’s

insulation is adequate,

o check the condition of the engine in terms of running and lubrication.

The decoder is available with different interfaces according to the different

standards.

DigiDrive-x.1:

The outputs of the decoder have the standard NEM652 interface.

When attaching the decoder be careful to link the orange output of the interface to

pin 1 on the printed circuit, which is usually indicated with an asterisk.

In the event of an incorrect attachment, no damage is done, but the lighting

functions will nor work.

The standard length of the cable is 8 cm, but different cable lengths are available for

in-dividual orders.

DigiDrive-x.2:

The outputs of the decoder have the standard 6-pole NEM651 interface.

In the event of an incorrect attachment, no damage is done, but the locomotive

won’t work. In this case attach the dvice in the different direction.

DigiDrive-x.3:

The outputs of the decoder are being shipped with 8cm length of cables, without

interface.

This type is ideal for digitalizing old models which do not have printed circuit for mo-

tor.

The list below will help you attach the unit:

Orange: Right motor terminal

Yellow: Rear light

Green: AUX1 function output

Red: Right track connection

Grey: Left motor terminal

White: Headlight

Blue: Function interface. Common „+” pole

Black: Left track connection

Purple: AUX2 function output

DigiDrive-x.5:

The outputs of the decoder have standard NEM 658, PLUX22 interface.

The missing pin in the middle of the pin line is the „index” pin. On the preparatory

panel of the locomotive, the holes for this pin are omitted or marked separately.

Sizes: 15 mm x 18 mm x 4.0 mm

Index pin

Installation:

After having installed the decoder, check the position of the cables, they should not

be in the way of any moving or rotating part. If everything is fine, you may start the

voltage test.

Motor control interface:

The decoder can control one permanent magnetic commutator direct current motor.

The H bridge made of FET transistors continuously has maximum 1A current.

The load control frequency is 18kHz.

The output is short circuit protected.

The protection is guaranteed only in case of standard installation! If during

assembling or because of an incorrect installation a short circuit should occur, for

example, if one of the cables of the motor output (grey, orange) and the rail cables

(black, red) touch, this may result in damage in the decoder.

If the short circuit protection sign alarms the decoder can only be reinstalled after

the isolation of voltage.

Setting the load control:

The CV registers shown in the following chart belong to the motor speed control:

speed

control

Bit 7

(128)

Bit 6

(64)

Bit 5

(32)

Bit 4

(16)

Bit 3

(8)

Bit 2

(4)

Bit 1

(2)

Bit 0

(1)

CV51 Effect of load control in consist mode

CV52 Effect of load control in normal mode

CV54 Boosting the proportional part. Default value is 3.

CV55 Boosting the integrating part. Default value is 3.

CV56 Boosting the derivative part. Default value is 128.

CV49 *enable

PID.

*enable PID: enabling the operation of the load control

Questo manuale è adatto per i seguenti modelli

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente