Dimplex CEL50 Manuale utente

Owner’s Manual

Model

CEL50

7215570100R00

IMPORTANT SAFETY INFORMATION: Always read this manual rst

before attempting to install or use this replace. For your safety, always

comply with all warnings and safety instructions contained in this manual

to prevent personal injury or property damage.

To view the full line of Dimplex products, please visit

www.dimplex.com

2 www.dimplex.com

Table of Contents

Always use a qualied technician or

service agency to repair this replace.

!NOTE: Procedures and

techniques that are considered

important enough to emphasize.

CAUTION: Procedures and

techniques which, if not carefully

followed, will result in damage to

the equipment.

WARNING: Procedures and

techniques which, if not carefully

followed, will expose the user to

the risk of re, serious injury, or

death.

Welcome & Congratulations ..................3

IMPORTANT INSTRUCTIONS ................ 4

Quick Reference Guide ......................7

Fireplace Installation .......................8

Site Selection ..................................... 8

Hardwire Installation ................................ 9

Wiring ........................................... 9

Surface Installation ................................ 12

In-wall Recessed Installation - 2x4 Framing ............. 14

Flush Mounted Installation - 2x8 Framing ................ 15

Front Glass Installation ............................. 17

Operation ...............................18

Maintenance .............................21

Accessories ..............................21

Warranty ................................22

Technical Support .........................24

Welcome & Congratulations

Serial Number

Label Rating Label

Thank you and congratulations for purchasing an electric replace from

Glen Dimplex Americas. Please use our convenient online registration

page to record your model and serial numbers for future reference at:

www.dimplex.com/register

NO NEED TO RETURN TO THE STORE

Questions with operation or assembly? Require Parts Information?

Product Under Manufacturer’s Warranty?

For Troubleshooting and Technical Support

OR Toll-Free 1-888-346-7539

Monday to Friday 8:00 a.m. to 4:30 p.m. EST

In order to better serve you, please have your model and serial number

ready or register your product online before calling (See above)

Please carefully read and save these instructions.

CAUTION: Read all instructions and warnings carefully before

starting installation. Failure to follow these instructions may result

in a possible electric shock, re hazard and will void the warranty.

4 www.dimplex.com

When using electrical appliances,

basic precautions should always

be followed to reduce the risk of

fire, electric shock, and injury to

persons, including the following:

① Read all instructions before

using this electric replace.

② This replace is hot when in

use. To avoid burns, do not let

bare skin touch hot surfaces.

The surface around the heater

outlet becomes hot during heater

operation.

DANGER: High temperatures

may be generated under certain

abnormal conditions. Do not

partially or fully cover or obstruct

the front of this heater.

③Extreme caution is necessary

when any heater is used by or

near children or invalids and

whenever the unit is left operating

and unattended.

④Young children should be

supervised to ensure that they do

not play with the appliance.

⑤ The appliance is not intended

for use by young children

or inrmed persons without

supervision.

⑥Do no operate any heater

after it malfunctions. Disconnect

IMPORTANT INSTRUCTIONS

power at service panel and have

heater inspected by a reputable

electrician before reusing.

⑦ If the supply cord is damaged,

it must be replaced by the

manufacturer, or its service

agent, or a qualied person in

order to avoid a hazard. Contact

Technical Service for obtaining a

replacement cord at

1-888-346-7539.

⑧ Do not use outdoors.

⑨Never locate replace where

it may fall into a bathtub or other

water container.

⑩ Do not locate the heater

immediately below a xed

socket-outlet.

⑪ To disconnect the replace,

turn the controls off, and turn off

power to heater circuit at main

disconnect panel.

⑫Do not insert or allow foreign

objects to enter any ventilation

or exhaust opening as this may

cause an electric shock or re, or

damage to the heater.

⑬ To prevent a possible fire, do

not block air intakes or exhaust in

any manner.

⑭ A heater has hot and arcing or

sparking parts inside. Do not use

SAVE THESE INSTRUCTIONS

in areas where gasoline, paint,

or ammable liquids are used or

stored.

⑮Use this heater only as

described in this manual. Any

other use not recommended by

the manufacturer may cause fire,

electric shock or injury to persons.

⑯ To reduce the risk of electric

shock, this appliance has a

polarized plug (one blade is wider

than the other). This plug will

fit in a polarized outlet only one

way. If the plug does not fit fully

in the outlet, reverse the plug.

If it still does not fit, contact a

qualified electrician to install the

proper outlet. Do not change the

plug in any way. Always plug

heaters directly into a wall outlet/

receptacle. Never use with an

extension cord or relocatable

power tap (outlet/power strip).

⑰Do not burn wood or other

materials in the electric replace.

⑱ Do not strike the replace

glass.

⑲ Always use a certied

electrician should new circuits or

outlets be required.

⑳Always use properly

grounded, fused and polarized

outlets.

㉑ Disconnect all power supply

before performing any cleaning,

maintenance or relocation of the

unit.

㉒ When transporting or storing

the unit and cord, keep in a

dry place, free from excessive

vibration and store so as to avoid

damage.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

NO USER-SERVICABLE PARTS INSIDE

IMPORTANT INSTRUCTIONS

6 www.dimplex.com

!NOTE: This equipment has been

tested and found to comply with

the limits for Class B digital device,

pursuant to part 15 of the FCC Rules.

These limits are designed to provide

reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses and

can radiate radio frequency energy

and, if not installed and used in

accordance with the instructions, may

cause harmful interference to radio

or television reception, which can be

determined by turning the equipment

off and on, the user is encouraged to

try to correct the interference by one or

more of the following measures:

· Increase the separation between

the equipment and the receiver.

· Connect the equipment into an

outlet on a circuit different from that

to which the receiver is connected.

· Consult the dealer or an

experienced radio/TV technician for

help.

Operation is subject to the following

two conditions: (1) this device may not

cause interference and (2) this device

must accept any interference, including

interference that may cause undesired

operation of the device.

IMPORTANT INSTRUCTIONS

WARNING: The top of the

replace is to be installed a minimum

of 4" (102mm) from the ceiling.

WARNING: Remote control

contains small batteries. Keep away

from children. If swallowed, seek

medical attention immediately.

WARNING: Do not install battery

backwards, charge, put in re or mix

with used or other battery types - may

explode or leak causing injury.

!NOTE: Changes or modications

not expressly approved by the party

responsible for compliance could

void user's authority to operate the

equipment.

Quick Reference Guide

Figure 1

① The electrical information

regarding your electric replace can

be found on the rating label located

on the front of the unit, behind the

glass.

Before installation, please record your

replace's serial number below for

future reference.

② If you have any technical

questions or concerns regarding the

operation of your electric replace,

or require service contact customer

service.

③ For dimensions of your replace,

refer to Figure 1.

3" (7.6 cm)

50 516" (128 cm)

19 12

(49.5 cm)

46" (116 cm)

48 12 " (123 cm)

(17.8 cm)

3 1316"

(9.7 cm)

18"

(45.7 cm)

16"

(40.6 cm)

8 www.dimplex.com

Site Selection

Review and consider all of the

following conditions for installation:

• Dimensions of the unit: 505/16"

(128cm) x 19½" (49.5cm)

• Unit requires a minimum of two

wall studs in order to ensure a

secure installation

Three possible installation

methods:

• Surface mount (pg. 12); In-wall

Recessed (pg. 13); or Flush

mount (pg. 15)

• Hardwired or plug-in method

CAUTION: Ensure installation

does not allow replace to be in

direct contact with building vapor

barrier or insulation and meets all

local building code.

!NOTE 1: A 15 Amp, 120 Volt

circuit is required. A dedicated

circuit is preferred but not

essential in all cases. A dedicated

circuit will be required if, after

installation, the circuit breaker

trips or fuse blows on a regular

basis when the heater is

operating. Additional appliances

on the same circuit may exceed

the current rating of the circuit

breaker.

WARNING: Ensure the power

cord is not installed so that it is

Fireplace Installation

pinched or against a sharp edge

and ensure that the power cord

is stored or secured to avoid

tripping or snagging to reduce

the risk of re, electric shock or

injury to persons.

Construction and electrical

outlet wiring must comply

with local building codes and

other applicable regulations to

reduce the risk of re, electric

shock and injury to persons.

WARNING: To reduce the

risk of re, do not store or use

gasoline or other ammable

vapors or liquids in the vicinity of

the heater.

1. Select a location that is not

susceptible to moisture and

is away from drapes, furniture

and high trafc.

2. For ease of electrical hook up

you may wish to locate the

replace near an existing outlet

(for plug-in convenience) (refer

to NOTE 1).

3. Remove replace, front glass

and hardware from box and

remove all packaging materials

before installation.

4. Store the replace in a safe,

dry and dust free location until

you are ready to install the

replace.

Fireplace Installation

Hardwire Installation

The replace is packaged with a

two prong plug installed for plug-

in convenience. Hard wiring the

replace is also an option for any

installation.

WARNING: Do not attempt to

wire your own new outlets or

circuits. To reduce the risk of

re, electric shock or injury to

persons, always use a licensed

electrician.

WARNING: Ensure that the

On/Off Switch is set to the Off

position (refer to Operation

section) and that the circuit

on which the replace is to be

installed has the power cut

off at the service panel until

installation is complete.

1. Remove the partially reective

glass from the replace:

• Lay replace on its back.

Figure 2

Partially

Reective Glass

Glass Bracket

Bracket Screws

• Remove two Phillips screws

from each of the two glass

brackets (Figure 2).

• Remove glass brackets.

• With one hand keeping

pressure on the partially

reective glass, tilt the

replace upright and slightly

forward to allow the partially

reective glass to fall out of

the inside framing.

120V~

60Hz

RL3

RL2

RL1

LED LIGHTS

LED CONTROL

BOARD

Wiring

10 www.dimplex.com

3. Remove one Phillips screw to

release the electrical box cover

in the bottom, right corner of

the replace (Figure 4).

4. Carefully remove the electrical

box cover from the replace

as wires are fed through the

strain reliefs on the cover and

are connected within.

CAUTION: Partially reective

glass is not tempered. Do not

bump or drop the partially

reective glass to avoid breakage

and personal injury.

• Remove partially reective

glass from replace.

2. Remove six Phillips screws

that fasten the media tray

and two screws that

fasten the front panel tabs

(Figure 3). Carefully remove

both components.

Fireplace Installation

Figure 5 Wires to

controls

Wire connectors

Junction

Box screw

Figure 6

Junction Box screws (3)

Figure 4

Electrical box

Screw

Figure 3

Front Panel

Front Panel tabs (2)

Media Tray screws (2)

Indice

Lingue:

Altri manuali Dimplex Stufa

Dimplex

Dimplex FFCH5000W Series Manuale utente

Dimplex

Dimplex 402T Manuale utente

Dimplex

Dimplex AC3CN Manuale utente

Dimplex

Dimplex TAYLOR SUITE Manuale utente

Dimplex

Dimplex AC3CE Manuale utente

Dimplex

Dimplex EUH02B21T Manuale utente

Dimplex

Dimplex ECW 934 Manuale utente

Dimplex

Dimplex QSH-70 Manuale utente

Dimplex

Dimplex QM050 Manuale utente

Dimplex

Dimplex XT12 Manuale utente

Dimplex

Dimplex OFRC20TI Manuale utente

Dimplex

Dimplex SOLAR ST0133 Manuale utente

Dimplex

Dimplex EF 12/20 TI Manuale utente

Dimplex

Dimplex WMCS712N Manuale utente

Dimplex

Dimplex FW 550S Manuale utente

Dimplex

Dimplex ML2TS Manuale utente

Dimplex

Dimplex Saletto LPP050E Manuale utente

Dimplex

Dimplex OFRC15FA Manuale utente

Dimplex

Dimplex AC3N Manuale utente

Dimplex

Dimplex DHCER20WIFI Manuale utente

Dimplex

Dimplex CXLS12N Manuale utente

Dimplex

Dimplex BLF3451 Manuale utente

Dimplex

Dimplex Studio 842 Manuale utente

Dimplex

Dimplex BY 802 S Manuale utente

Manuali Stufa popolari di altre marche

oventrop

oventrop Regucor Series Manuale utente

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuale utente

ELMEKO

ELMEKO ML 150 Manuale utente

BN Thermic

BN Thermic 830T Manuale utente

KING

KING K Series Guida

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guida rapida

Well Straler

Well Straler RC-16B Manuale utente

EUROM

EUROM 333299 Manuale utente

Heylo

Heylo K 170 Manuale utente

Eterna

Eterna TR70W Manuale utente

Clarke

Clarke GRH15 Manuale di istruzioni

IRSAP

IRSAP The Radiator Company Ovali Manuale utente

Empire Heating Systems

Empire Heating Systems WCC65 Manuale utente

Wetekom

Wetekom 92 86 43 Manuale utente

Desa

Desa SPC170-F Manuale utente

Watlow

Watlow Watrod Electric Tubular Heaters Manuale utente

Haverland

Haverland ECO-DRY GPS Series Manuale elenco delle parti

Stelpro

Stelpro ASILVC2060 Series Manuale utente