Dimplex BF45DXP Manuale utente
Owner’s Manual
Model
BF45DXP
BF39STP/DXP
BF33STP/DXP
7206360500R04
IMPORTANT SAFETY INFORMATION: Always read this manual rst
before attempting to install or use this replace. For your safety, always
comply with all warnings and safety instructions contained in this manual
to prevent personal injury or property damage.
To view the full line of Dimplex products, please visit
www.dimplex.com
2 www.dimplex.com
Table of Contents
Always use a qualied technician
or service agency to repair
this replace.
!NOTE: Procedures and
techniques that are considered
important enough to emphasize.
CAUTION: Procedures and
techniques which, if not carefully
followed, will result in damage to
the equipment.
WARNING: Procedures
and techniques which, if not
carefully followed, will expose
the user to the risk of re,
serious injury, or death.
Welcome & Congratulations ...................3
IMPORTANT INSTRUCTIONS .................4
Fireplace Installation ........................5
Operation ..................................6
Maintenance ...............................8
Accessories .............................. 11
Warranty ................................ 11
Replacement Parts .........................14
3
Welcome & Congratulations
Thank you and congratulations for choosing to purchase an electric
replace from Dimplex, the world leader in electric replaces.
Please carefully read and save these instructions.
CAUTION: Read all instructions and warnings carefully before
starting installation. Failure to follow these instructions may result in a
possible electric shock, re hazard and will void the warranty.
Please record your model and serial numbers below for future
reference: model and serial numbers can be found on the Model and
Serial Number Label of your replace.
Model Number ______________ Serial Number ______________
NO NEED TO RETURN TO THE STORE
Questions with operation or assembly? Require Parts Information?
Product Under Manufacturer’s Warranty?
Contact us at: www.dimplex.com/customer_support
For Troubleshooting and Technical Support
OR Toll-Free 1-888-DIMPLEX (1-888-346-7539)
Monday to Friday 8:00 a.m. to 4:30 p.m. EST
Please have your model number and product serial
number ready. (See above)
Model
Number
XXXXX
SERIAL No.
4 www.dimplex.com
When using electrical appliances,
basic precautions should always
be followed to reduce the risk of
fire, electric shock, and injury to
persons, including the following:
① Read all instructions before
using this appliance.
② This replace is hot when in
use. To avoid burns, do not let
bare skin touch hot surfaces.
The trim around the heater outlet
becomes hot during heater opera-
tion. Keep combustible materials,
such as furniture, pillows, bed-
ding, papers, clothes, and cur-
tains at least 3 feet (0.9m) from
the front of the unit.
③ Extreme caution is neces-
sary when any heater is used by
or near children or invalids and
whenever the replace is left
operating and unattended.
④ Do not operate any heater after
it malfunctions. Disconnect power
at the service panel and have the
heater inspected by a reputable
electrician before reusing.
IMPORTANT INSTRUCTIONS
SAVE THESE INSTRUCTIONS
⑤Do not operate any unit with
a damaged cord or plug, or if the
heater has malfunctioned, or if
the electric replace has been
dropped or damaged in any man-
ner, contact Dimplex Technical
Service at 1-888-346-7539.
⑥ Never locate this heater where
it may fall into a bathtub or other
water container.
⑦ Do not use outdoors.
⑧Do not insert or allow foreign
objects to enter any ventilation
or exhaust opening as this may
cause an electric shock or fire, or
damage to the heater.
⑨ To prevent a possible fire, do
not block air intake or exhaust in
any manner.
⑩ All electrical heaters have
hot and arcing or sparking parts
inside. Do not use in areas where
gasoline, paint, or ammable
liquids are used or stored
⑪ Do not modify this replace.
Use it only as described in this
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
NO USER-SERVICEABLE PARTS INSIDE
5
IMPORTANT INSTRUCTIONS
manual. Any other use not recom-
mended by the manufacturer may
cause re, electric shock or injury
to persons.
⑫Do not burn wood or other
materials in this replace.
⑬ Do not strike replace glass.
⑭ Always use a certied electri-
cian for installation.
⑮ Disconnect all power coming
to replace at main service panel
before performing any cleaning,
or maintenance.
⑯ When transporting or storing
the replace, keep in a dry place,
free from excessive vibration and
store as to avoid damage.
!NOTE: Changes or modications
not expressly approved by the party
responsible for compliance could void
user's authority to operate the equip-
ment.
Fireplace Installation
Bathroom Installation
This rebox must be protected
by a GFI circuit. If a receptacle
is used it must be readily
accessible.
To prevent electrical shock this
unit is an electrical appliance
that is not watertight and must be
installed as to prevent water from
entering the unit. This unit must
be installed away from showers,
tubs, etc. Never locate replace
where it may fall into a bathtub or
other water containers. Keep tow-
els and other combustible materi-
als 3 feet (0.9 m) away from the
front of the unit.
6 www.dimplex.com
Operation
Figure 1
WARNING: This electric
rebox must be properly installed
before it is used.
Manual Controls
(Figure 1)
The controls for the Electric Fire-
place are located at the bottom
right hand corner of the unit.
CAUTION: Ensure that the
Voltage Selector switch is set
to the appropriate voltage
(115V or 230V)
A. On/Off Switch
The on/off switch energizes the
rebox and ame.
B. Mode Selector Switch
Select preferred feature:
• “o” for ame only
• “-“ for PurireTM only/ame.
• “=” for heat/PurireTM/ame
!NOTE: The heater may emit
a slight, harmless odor when rst
used. This odor is a normal con-
dition caused by initial heating of
internal heater parts and will not
occur again.
C. Voltage Selector Switch
Needs to be set to reect the in-
coming voltage to the unit - 115V
or 230V.
Resetting The Temperature
Cutoff Switch
The heater on this replace is
protected with a safety device to
prevent overheating. Should the
heater overheat, the Overheat
indicator will be activated (Fig. 1),
and an automatic cutout will turn
the heater off and it will not come
Overheat
Indicator
Manual Controls
B. Mode
Selector Switch
A. On/Off
Switch
C. Voltage Selector
Switch
7
Operation
back on without being reset. It
can be reset by switching the On/
Off switch to OFF and waiting 5
minutes before switching it to ON.
The overheat cutout will be trig-
gered if the lter is dirty. Follow
lter maintenance.
CAUTION: If you need to
continuously reset the heater, dis-
connect power and call Dimplex
customer service at
(1-888-346-7539).
Remote Controls
An optional remote control can
be purchased to operate the
replace - BFRC-KIT. This
will allow the user the ability to
toggle through the three stages
of operation: Flames, Flames and
PurireTM, and Flames/ PurireTM/
Heat, with a remote control.
Wall Mounted Controls
The replace can be installed with
wall mounted controls. These
controls include wall switches
and thermostats. (see individual
installation guides for details)
1. Wall Mounted Switches
This model may be installed
so that a wall mounted switch
energizes the rebox and
ame, (On/Off Switch must
be in the ON position). A
wall mounted switch may
also be used to override the
ame image, (On/Off Switch
must be in the ON position
in coordination with any
main power wall mounted
switch). A wall mounted
switch may also be used
to override the heater/Puri-
reTM option (Mode Selector
Switch must be in the “=”
position).
2. Wall Mounted Thermostat
This unit may be installed so
that a wall mounted ther-
mostat can adjust the heat
temperature to your individual
requirements. Please refer
to thermostat manufacturers
operation Instructions. Mode
Selector Switch must be
set to “=” for thermostat to
control heater/PurireTM.
3. Wall Mounted Remote Controls
(WRCPF-KIT)
Dimplex manufactures a
optional wall mounted remote
control which allows the user
to fully control the replace
from a central location with
the added functionality of a
built in thermostat.
8 www.dimplex.com
Maintenance
WARNING: Disconnect power
and heater has cooled before
attempting any maintenance or
cleaning to reduce the risk of
re, electric shock or damage
to persons.
!NOTE: The replace should
not be operated with an accumu-
lation of dust or dirt on or in the
unit, as this can cause a build up
of heat and eventual damage. For
this reason the heater must be
inspected regularly, depending
upon conditions and at least at
yearly intervals.
Light Bulb Replacement
Light bulbs need to be replaced
when you notice a dark section
of the ame or when the clar-
ity and detail of the log exterior
disappears. There are four bulbs
under the log set which generate
the ames and embers.
Helpful Hints: It is a good idea to
replace all light bulbs at one time
if they are close to the end of their
rated life. Group replacement will
reduce the number of times you
need to open the unit to replace
light bulbs. Long life bulbs are
recommended to reduce the fre-
quency of bulb changes.
Light Bulb Requirements:
Quantity of 4 clear chandelier or
candelabra bulbs with an E-12
(small) socket base, 60 Watt rat-
ing. Example: GE 60BC or Phil-
ips 60CTC. DO NOT EXCEED 60
WATTS PER BULB.
CAUTION: When handling log
only apply force to the ember bed
section not directly to the logs.
To access the light bulb area
CAUTION: Allow at least 5
minutes for light bulbs to cool off
before touching bulbs to avoid ac-
cidental burning of skin.
1. Open steel curtain (remove
glass doors if applicable).
2. Remove two screws on log
bracket and set aside
(Figure 2)
3. Pull front edge of plastic
ember bed or plastic grate up
and forward until rear tab re-
Screws
Figure 2
9
leases from the ledge located
at the bottom of the partially
reective glass (Figure 3).
!NOTE: Log set ts tightly into
rebox, some force may be nec-
essary to remove.
4. Set logset in front of rebox.
5. Disconnect the logset LED
wire harness from unit
(Figure 4).
6. Examine the bulbs to de-
termine which bulbs require
replacement.
7. Unscrew bulbs counter clock-
wise.
8. Insert new bulbs.
9. Re-connect the logset LED
wire harness to the unit.
10. Replace the log by inserting
the rear tab of the logset un-
der the back ledge of the re-
place and push down on the
front edge of the logset until it
snaps into place (Figure 3).
11. Replace log grate using two
screws previously removed.
Purire™ Filter
The Purire™ lter supplied in
your replace is reusable and
washable. The lter should be
cleaned or replaced on average
once a year, or if overheat indica-
tor lamp is activated. To clean
the lter gently tap lter on a hard
surface to dislodge any loose dirt
or debris, and then clean with
water. Do not use soap or clean-
ing products, as they may dam-
age the lter. The lter size is 20”
X 10” X 1” rated at MERV 10. If
using an after market lter follow
the manufacturers recommended
replacement instructions.
To replace lter:
Maintenance
Side Section
Back
Ledge
Rear
Tab
Log
Ember
bed
Front
Edge
LED Wire
Harness
Figure 3
Figure 4
10 www.dimplex.com
1. Remove the 2 mounting
screws from the air lter
bracket.
2. Slide forward to remove the
air lter bracket assembly
from the rebox.
3. Slide lter out of air lter
bracket.
4. Reassemble in reverse order
as above.
!NOTE: If after market air
lter is used ensure it is installed
according to the manufacturers
recommended instructions.
Maintenance
Purire™
Filter
Filter
Bracket
Mounting
Screws
Figure 6 Partially Reective Glass
Cleaning
The partially reective glass is
cleaned in the factory during
the assembly operation. During
shipment, installation, handling,
etc., the partially reective glass
surface may collect dust particles.
These can be removed by bufng
lightly with a clean dry cloth.
To remove ngerprints or other
marks, the partially reective
glass can be cleaned with a damp
cloth using high quality house-
hold glass cleaner. The partially
reective glass should be com-
pletely dried with a lint free cloth.
To prevent scratching, do not use
abrasive cleaners or spray liquids
on any surface.
Fireplace Surface Cleaning
Use warm water only to clean
painted surfaces of the Compact
Fireplace. Do not use abrasive
cleaners.
Servicing
Except for light bulb replacement
and cleaning described above, an
authorized service representative
should perform any other servicing.
Altri manuali per BF45DXP
2
Questo manuale è adatto per i seguenti modelli
4
Indice
Altri manuali Dimplex Camino da interno
Dimplex
Dimplex MINI MOZART Manuale utente
Dimplex
Dimplex BFSL33 Manuale utente
Dimplex
Dimplex Mini Mozar DFP15-1131 Manuale utente
Dimplex
Dimplex DNV20AB Manuale utente
Dimplex
Dimplex Figaro FGA15 Manuale utente
Dimplex
Dimplex BLF7451 Manuale utente
Dimplex
Dimplex GDS28L8-1941WE Manuale utente
Dimplex
Dimplex Dakota DKT20 Manuale utente
Dimplex
Dimplex DWOP20R Manuale utente
Dimplex
Dimplex 25 FIREBOX Manuale utente
Dimplex
Dimplex ENG56-400 Manuale tecnico
Dimplex
Dimplex DF2305 Manuale utente
Dimplex
Dimplex CASSETTE M Manuale utente
Dimplex
Dimplex GDS28G8-1802W Manuale utente
Dimplex
Dimplex BOF4056 Manuale utente
Dimplex
Dimplex Revillusion RBF24DLX Manuale utente
Dimplex
Dimplex 3-STEP Optimyst Manuale di istruzioni
Dimplex
Dimplex Montclair Manuale utente
Dimplex
Dimplex DFI400R Manuale utente
Dimplex
Dimplex DFB8842 Manuale utente
