Dimplex THWG XLF50 Manuale utente

Owner’s Manual

Model

XLF50

XLF74

XLF100

7214410100R06

IMPORTANT SAFETY INFORMATION: Always read this manual rst

before attempting to install or use this replace. For your safety, always

comply with all warnings and safety instructions contained in this manual

to prevent personal injury or property damage.

To view the full line of Dimplex products, please visit

www.dimplex.com

2 www.dimplex.com

Table of Contents

Always use a qualied technician or

service agency to repair this replace.

!NOTE: Procedures and

techniques that are considered

important enough to emphasize.

CAUTION: Procedures and

techniques which, if not carefully

followed, will result in damage to

the equipment.

WARNING: Procedures and

techniques which, if not carefully

followed, will expose the user to

the risk of re, serious injury, or

death.

Welcome & Congratulations ...................... 3

IMPORTANT INSTRUCTIONS ....................4

Quick Reference Guide .......................... 6

Fireplace Installation ............................ 7

Installation .................................... 7

For Bathroom Use ............................. 12

Final Assembly ............................... 12

Operation .................................... 14

Maintenance ................................. 19

Warranty .................................... 20

Technical Support ............................. 22

Welcome & Congratulations

Thank you and congratulations for purchasing an electric replace from

Dimplex. Please use our convenient online registration page to record

your model and serial numbers for future reference at

www.dimplex.com/register

NO NEED TO RETURN TO THE STORE

Questions with operation or assembly? Require Parts Information?

Product Under Manufacturer’s Warranty?

For Troubleshooting and Technical Support

OR Toll-Free 1-888-346-7539

In order to better serve you, please have your model and serial number

ready or register your product online before calling (See above)

Model and Serial

Number Label

Please carefully read and save these instructions.

CAUTION: Read all instructions and warnings carefully before

starting installation. Failure to follow these instructions may result in

a possible electric shock, re hazard and will void the warranty.

4 www.dimplex.com

When using electrical appliances,

basic precautions should always

be followed to reduce the risk of

fire, electric shock, and injury to

persons, including the following:

① Read all instructions before

installing or using this electric

replace.

② This replace is hot when in

use. To avoid burns, do not let

bare skin touch hot surfaces.

The trim around the heater outlet

becomes hot during heater

operation.

DANGER: High temperatures

may be generated under certain

abnormal conditions. Do not

partially or fully cover or obstruct

the front of this heater.

③Extreme caution is necessary

when any heater is used by or

near children or invalids and

whenever the unit is left operating

and unattended.

④Young children should be

supervised to ensure that they do

not play with the appliance.

⑤ The appliance is not intended

for use by young children

or inrmed persons without

supervision.

IMPORTANT INSTRUCTIONS

⑥Do not operate the unit after

it malfunctions. Disconnect power

at the service panel and contact

Customer Service for service

1-888-346-7539.

⑦ Do not use outdoors.

⑧Never locate replace where

it may fall into a bathtub or other

water container.

⑨ To disconnect the replace,

turn the controls o󰀨, then

disconnect the circuit at the main

disconnect panel.

⑩ Do not locate the heater

immediately below a xed socket-

outlet.

⑪Do not insert or allow foreign

objects to enter any ventilation

or exhaust opening as this may

cause an electric shock or re, or

damage to the heater.

⑫ To prevent a possible fire, do

not block air intakes or exhaust in

any manner.

⑬ All electrical heaters have

hot and arcing or sparking parts

inside. Do not use in areas where

gasoline, paint, or ammable

liquids are used or stored.

SAVE THESE INSTRUCTIONS

⑭Use this heater only as

described in this manual. Any

other use not recommended by

the manufacturer may cause re,

electric shock or injury to persons.

⑮Do not burn wood or other

materials in the electric replace.

⑯ Do not strike the replace

glass.

⑰ Always use a certied

electrician should new circuits be

required.

⑱ Disconnect all power supply

before performing any cleaning,

maintenance or relocation of the

unit.

⑲When transporting or storing

the unit and cord, keep in a

dry place, free from excessive

vibration and store so as to avoid

damage.

WARNING: Remote control

contains small batteries.

Keep away from children. If

swallowed, seek medical attention

immediately.

WARNING: Do not install

battery backwards, charge, put

in re or mix with used or other

battery types - may explode or

leak causing injury.

!NOTE: Changes or

modications not expressly

approved by the party responsible

for compliance could void

user's authority to operate the

equipment.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

NO USER-SERVICABLE PARTS INSIDE

IMPORTANTINSTRUCTIONS

6 www.dimplex.com

Quick Reference Guide

Figure 1

1. The electrical information

regarding your electric

replace can be found on the

rating label located on the top

of the unit.

Please use our convenient online

registration page to record your

model and serial numbers for

future reference at

www.dimplex.com/register

2. If you have any technical

questions or concerns

regarding the operation

of your electric replace,

or require service contact

Customer Service at

1-888-346-7539.

3. For dimensions of your

replace, refer to Figure 1.

16.49 in

419 mm

15.82 in.

402 mm

15.00 in.

381 mm

5.79 in.

147 mm

4.34 in.

110 mm

XLF50 50.31 in [1278 mm]

XLF74 74.31 in [1887 mm]

XLF100 100.31 in [2548 mm]

XLF50 51.41 in [1306 mm]

XLF74 75.41 in [1941 mm]

XLF100 101.41 in [2576 mm]

CAUTION: Ensure installation

does not allow replace to be in

direct contact with building vapor

barrier or insulation and meets all

local building code.

NOTE: A dedicated, properly

fused 15 Amp circuit is required,

rated for the appropriate voltage

(120V, 240V).

WARNING: Construction

and wiring must comply with

local building codes and other

applicable regulations to

reduce the risk of re, electric

shock and injury to persons.

WARNING: To reduce the risk

of re, electric shock or injury to

persons, always use a licensed

electrician.

WARNING: To reduce

the risk of re, do not store

or use gasoline or other

ammable vapors or liquids

in the vicinity of the heater.

1. Select a location that

is not susceptible to

moisture and is away from

drapes, furniture and high

tra󰀩c.

2. Unpack the replace and

hardware from the box.

Fireplace Installation

!NOTE: Leave the front

glass and partially reective

glass, safely, in the box until

the time you are ready to

install it.

4. Store the replace in a safe,

dry and dust free location until

you are ready to install the

replace.

Installation

CAUTION: Two people will be

required for various steps of

this procedure.

This design of this unit allows

three options for installation:

partial recess, ush mounted or

sub-surface mounted.

XLF50: 50 5/8" (128.6 cm)

2” x 6”

5 1/2" (14.0 cm)

16"

(40.6 cm)

XLF74: 74 5/8" (189.7 cm)

XLF100: 100 5/8" (255.7 cm)

2” x 4”

3 1/2" (9.0 cm)

Figure 2

8 www.dimplex.com

Fireplace Installation

CAUTION: Sub-surface

mounting should be limited to ½

in. (10 mm) to ensure adequate

air ow of heated air out of the

rebox area.

1. Prepare a wall with a framed

opening of 16 in. (40.6 cm)

high,

• XLF50 - 50 ⅝ in. (128.7 cm)

• XLF74 - 74 ⅝ in. (189.7 cm)

• XLF100 - 100 ⅝ in. (255.7 cm)

wide, with a bottom sill that is

a minimum of 3.5 in. (9.0 cm)

deep (gure 2). The sill can be

constructed to support the front

of the unit to allow the power

supply wires to easily be run

behind or ush with the back

of the unit and a pass thru hole

drilled for electrical wire routing.

!NOTE: It is recommended that

the bottom of the unit be mounted

between 30 in. (76.2 cm) and 40

in. (102 cm) from the ground to

maintain an optimized viewing

angle of the ame.

WARNING: Do not attempt

to wire your own new circuits. To

reduce the risk of re, electric shock

or injury to persons, always use a

licensed electrician.

WARNING: Ensure that the

circuit on which the replace is

to be installed has the power

cut o󰀨 at the service panel until

installation is complete.

2. The unit is provided with an

installed ¾ in. (2.0 cm) trim.

Depending on the installation,

this trim can be removed by

removing the securing screws

and the 4 trim pieces.

3. Ensuring a minimum of 18 in.

(46.7 cm) of slack, route the

supply power wire through a

cable clamp (not included) and

in the opening in the back of

the unit. (Figure 3)

4. Lift replace, from the bottom

and the handles located on the

back, and insert into opening to

the desired depth.

5. Using a bubble level (supplied)

ensure that the replace is level

Figure 3

Grounding

Screw

Cable Clamp

Fireplace Installation

within the framing. Adjust as

required.

6. Drive four supplied mounting

screws through the four

mounting holes located on the

inside surface of the replace

chassis, into wall studs

(Figure 4).

120V Installation - Direct Wire

!NOTE: The unit is designed

to be hardwired to a power

source and should not have

a cord installed to allow the

unit to be plugged into a wall

receptacle.

Use two conductor, non-metallic

sheath cable with ground wire

(3 wires total) for the incoming

power supply.

CAUTION: Use the

appropriate wire to meet local

Figure 4

Mounting Holes

and national electrical codes

for rated power consumption.

• Cut the wire to an appropriate

length.

• Connect the L wire from the

unit to the live wire from the

power supply with a wire nut.

• Connect the N wire from the

unit to the neutral wire from the

power supply with a wire nut.

• Connect the G wire from the

unit to the ground wire from

the power supply with a wire

nut or attach the grounding

wire to the cover with the

provided grounding screw, by

placing the wire in-between

screw and lock washer and

tighten (Figure 3).

• Ensure that all wires are

secure and do not protrude

Flame

Panel

10 www.dimplex.com

Fireplace Installation

past the ame panel, so as

not to be visible after nal

assembly.

• Continue to the nal assembly

instructions.

120V Installation - Wall Switch

!NOTE: Use a single pole,

single throw (On/O󰀨) wall switch

that is rated for a minimum of

15 amps.

!NOTE: The unit is designed

to be hardwired to a power

source and should not have

a cord installed to allow the

unit to be plugged into a wall

receptacle.

Use two conductor, non-metallic

sheath cable with ground wire

(3 wires total) for the incoming

power supply.

CAUTION: Use the

appropriate wire to meet local

and national electrical codes

for rated power consumption.

• Cut the wire to an appropriate

length.

• Connect the L wire from the

unit to the live wire from the

main power through the

wall switch, ensuring all live

connections are connected

with a wire nut.

• Connect the N wire from the

unit to the neutral wire from

the power supply with a wire

nut.

• Connect the G wire from the

unit to the ground wire from

the power supply with a wire

nut or attach the grounding

wire to the cover with the

provided grounding screw, by

placing the wire in-between

FIREPLACE JUNCTION BOX

120 V

POWER

SUPPLY

(BREAKER

PANEL)

WHITE - N

BLACK – L1

WHITE – N

BLACK – L1

GROUND - G

WALL

SWITCH

GROUND - G

Altri manuali per THWG XLF50

Questo manuale è adatto per i seguenti modelli

Indice

Lingue:

Altri manuali Dimplex Camino da interno

Dimplex

Dimplex CASSIDY Manuale utente

Dimplex

Dimplex Revillusion RLG20 EU Manuale utente

Dimplex

Dimplex SIL48M Manuale utente

Dimplex

Dimplex PF3033 Manuale utente

Dimplex

Dimplex DWOP20R Manuale utente

Dimplex

Dimplex ROTHESAY RSY20 Manuale utente

Dimplex

Dimplex BELLINI CONCRETE BLN15C Manuale utente

Dimplex

Dimplex 30" FIREPLACE Manuale utente

Dimplex

Dimplex Adagio Manuale utente

Dimplex

Dimplex CAS400LNH-INT Manuale utente

Dimplex

Dimplex GDS33HG-1310RG Manuale utente

Dimplex

Dimplex DNV20BR Manuale utente

Dimplex

Dimplex EWMC-CC-SS Manuale utente

Dimplex

Dimplex COMPACT FIREPLACE Manuale utente

Dimplex

Dimplex LVA231 Manuale utente

Dimplex

Dimplex CAS400 Manuale utente

Dimplex

Dimplex Opti-V PGF10 Manuale utente

Dimplex

Dimplex COMPACT FIREPLACE Manuale utente

Dimplex

Dimplex DF2624L-EUE Manuale utente

Dimplex

Dimplex DCF7850 Manuale utente

Dimplex

Dimplex Michigan Fire MCN20 Manuale utente

Dimplex

Dimplex SWM4220 Manuale utente

Dimplex

Dimplex 3 Step E Manuale utente

Dimplex

Dimplex DF1135M Manuale utente

Manuali Camino da interno popolari di altre marche

Brigantia

Brigantia 35-DVRS31N-2 Manuale del proprietario

Nordpeis

Nordpeis Bergen Manuale utente

Superior

Superior BCT2536TMN Manuale utente

Quadra-Fire

Quadra-Fire 5100I-GD-B Manuale utente

Renaissance

Renaissance RUMFORD 1000 Manuale utente

Lacunza

Lacunza IV-800 Manuale utente

Baxi

Baxi 940 Istruzioni per l’uso

Dru

Dru Maestro 60/2 Tall RCH Manuale utente

Diamond Fireglass

Diamond Fireglass SS-O22 Manuale utente

HearthStone

HearthStone Windsor Bay 8830 Manuale di programmazione

Napoleon

Napoleon ASCENT B42 Manuale utente

Enviro

Enviro E33GI Manuale utente

Smeg

Smeg L30 FABE Istruzioni di montaggio

KEDDY

KEDDY K700 Manuale utente

Godin

Godin 3451 Manuale utente

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manuale utente

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manuale utente

Desa

Desa CCFPDFT Manuale operativo