Dimplex ELECTRALOG CS4416 Manuale utente

Owner’s Manual

Models

CS4416

CS3311

CS2307

7207400100R08

IMPORTANT SAFETY INFORMATION: Always read this manual rst

before attempting to install or use this stove. For your safety, always

comply with all warnings and safety instructions contained in this manual

to prevent personal injury or property damage.

CS3311 Pictured

Table of Contents

Always use a qualied technician

or service agency to repair

this stove.

!NOTE: Procedures and

techniques that are considered

important enough to

emphasize.

CAUTION: Procedures

and techniques which, if not

carefully followed, will result in

damage to the equipment.

WARNING: Procedures

and techniques which, if not

carefully followed, will expose

the user to the risk of re,

serious injury, or death.

Welcome & Congratulations ........... 3

IMPORTANT INSTRUCTIONS . . . . . . . . . . . . . . .4

Quick Reference Guide ............... 7

Compact Stove Installation ............ 7

Operation .......................... 8

Maintenance....................... 10

Warranty ...............................12

ReplacementParts........................14

Welcome & Congratulations

Thank you and congratulations for choosing to purchase an electric

stove from Electralog.

Please carefully read and save these instructions.

CAUTION: Read all instructions and warnings carefully before

starting installation. Failure to follow these instructions may result in a

possible electric shock, re hazard and will void the warranty.

Please record your model and serial numbers below for future

reference: model and serial numbers can be found on the Model and

Serial Number labels of your stove.

Model Number

Serial Number

NO NEED TO RETURN TO THE STORE

Questions with operation or assembly? Require Parts Information?

Product Under Manufacturer’s Warranty?

For Troubleshooting and Technical Support

OR Toll-Free 1-888-DIMPLEX (1-888-346-7539)

Monday to Friday 8:00 a.m. to 4:30 p.m. EST

Please have your model number and product serial

number ready. (See above)

When using electrical appliances,

basic precautions should always be

followed to reduce the risk of re,

electric shock, and injury to persons,

including the following:

①Read all instructions before using

the Compact Stove.

②The heater is hot when in use.

To avoid burns, do not let bare skin

touch hot surfaces. The trim around

the heater outlet becomes hot during

heater operation. Keep combustible

materials, such as furniture, pillows,

bedding, papers, clothes, and

curtains at least 3 feet (0.9m) from

the front of the unit.

CAUTION: High Temperature.

Keep electrical cords, drapery, and

other furnishings at least 3 feet

(0.9m) from the front of the heater

and away from the side and rear.

③Extreme caution is necessary

when any heater is used by or

near children or invalids and

whenever the unit is left operating

and unattended.

④Always unplug the Compact

Stove when not in use.

⑤Do not operate any unit with a

damaged cord or plug, or if the heater

has malfunctioned, or if the Compact

Stove has been dropped or damaged

IMPORTANT INSTRUCTIONS

in any manner. Return heater

to authorized service facility for

examination, electrical or mechanical

adjustment, or repair.

⑥Do not use outdoors.

⑦The Compact Stove is not

intended for use in bathrooms,

laundry areas and similar indoor

locations. Never locate heater where

it may fall into a bathtub or other

water container.

⑧Do not run the cord under

carpeting. Do not cover cord with

throw rugs, runners, or the like.

Arrange cord away from trafc area

and where it will not be tripped over.

⑨To disconnect the unit, turn the

controls off, then remove the plug

from the outlet.

⑩Do not insert or allow foreign

objects to enter any ventilation or

exhaust opening as this may cause

an electric shock or re, or damage to

the heater.

⑪ To prevent a possible re, do

not block air intake or exhaust in any

manner. Do not use on soft surfaces,

like a bed, where openings may

become blocked.

⑫All electrical heaters have hot

and arcing or sparking parts inside.

SAVE THESE INSTRUCTIONS

Do not use in areas where gasoline,

paint, or ammable liquids are used

or stored or where the unit will be

exposed to ammable vapors.

⑬Do not modify the Compact

Stove. Use it only as described in

this manual. Any other use not

recommended by the manufacturer

may cause re, electric shock or

injury to persons.

⑭To reduce the risk of electric

shock, this appliance has a polarized

plug (one blade is wider than the

other). This plug will t in a polarized

outlet only one way. If the plug does

not t fully in the outlet, reverse the

plug. If it still does not t, contact

a qualied electrician to install the

proper outlet. Do not change the

plug in any way. Avoid the use of an

extension cord. Plug the cord directly

into an appropriate wall receptacle.

⑮Do not burn wood or other

materials in the Compact Stove.

⑯Do not strike the clear door

panel.

⑰ Always use a certied electrician

should new circuits or outlets be

required.

⑱Always use properly grounded,

fused and polarized outlets.

⑲Disconnect all power supply

before performing any cleaning,

maintenance or relocation of the unit.

⑳When transporting or storing the

unit and cord, keep in a dry place,

free from excessive vibration and

store so as to avoid damage.

IMPORTANT INSTRUCTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

NO USER-SERVICABLE PARTS INSIDE

IMPORTANT INSTRUCTIONS

CAUTION: This equipment has

been tested and found to comply with

the limits for Class B digital device,

pursuant to part 15 of the FCC

Rules. These limits are designed to

provide reasonable protection against

harmful interference in a residential

installation. This equipment

generates, uses and can radiate

radio frequency energy and, if not

installed and used in accordance with

the instructions, may cause harmful

interference to radio or television

reception, which can be determined

by turning the equipment off and

on, the user is encouraged to try to

correct the interference by one or

more of the following measures:

Reorient or relocate the receiving•

antenna.

Increase the separation between•

the equipment and the receiver.

Connect the equipment into an•

outlet on a circuit different from

that to which the receiver is

connected.

Consult the dealer or an•

experienced radio/TV technician

for help.

Operation is subject to the following

two conditions: (1) this device may

not cause interference and (2) this

device must accept any interference,

including interference that may cause

undesired operation of the device.

WARNING: Remote control

contains small batteries. Keep away

from children. If swallowed, seek

medical attention immediately.

WARNING: Do not install battery

backwards, charge, put in re or mix

with used or other battery types - may

explode or leak causing injury.

!NOTE: Changes or modications

not expressly approved by the party

responsible for compliance could

void user's authority to operate the

equipment.

Quick Reference Guide

① Prior to the rst use of

the Compact Stove verify the

following:

Are the circuit breakers for•

the unit on?

Are the light bulbs in your•

Compact Stove loose? (To

check, follow the instructions

for replacing the light bulbs

under the Maintenance

section of this manual)

②The heater on your Compact

Stove may emit a slight, harmless

odor when rst used. This odor is

a normal condition caused by the

initial heating of internal heater

parts and will not occur again.

Compact Stove Installation

!NOTE: A 15 Amp, 120

Volt circuit is required. A

dedicated circuit is preferred

but not essential in all cases.

A dedicated circuit will be

required if, after installation,

the circuit breaker trips or

fuses blow on a regular basis

when the heater is operating.

Additional appliances on the

same circuit may exceed the

current rating of the circuit

breaker.

WARNING: Ensure the

power cord is not installed so

that it is pinched or against a

sharp edge and ensure that

the power cord is stored or

secured to avoid tripping or

snagging to reduce the risk of

re, electric shock or injury to

persons.

Construction and electrical

wiring must comply with local

building codes and other

applicable regulations to

reduce the risk of re, electric

shock and injury to persons.

Do not attempt to wire your

own new outlets or circuits. To

reduce the risk of re, electric

shock or injury to persons,

always use a licensed

electrician.

① Make sure the unit’s 3-Position

switch is switched OFF (refer to

operating instruction section).

② Plug the unit directly into a 15

Amp, 120 VAC outlet.

Operation

fan and the heater element.

When the switch is in the on “ I”

position the heater operates if the

thermostat calls for heat.

C. Heater Thermostat Control

To adjust the temperature to

your individual requirements,

turn the thermostat control

clockwise all the way to turn

on the heater. When the room

reaches the desired temperature,

turn the thermostat knob counter

clockwise until you hear a click.

Leave in this position to maintain

the room temperature at this

setting. For additional heat, turn

clockwise until you hear the click

again and the heater will turn on.

!NOTE: When the heater

is switched on, the heater

fan will operate. The heater

element may or may not be on

depending on the thermostat

control setting (see “Heater

Thermostat Control”).

Resetting the Temperature

Cutoff Switch

Should the heater overheat, an

automatic cut out will turn the

heater off and it will not come

back on without being reset. It

can be reset by switching the

Figure 1

A. 3-Position Switch

The switch has two On positions

marked with “ ” and “MANUAL”.

The “MANUAL” position is for

manual operation. In this position

the built-in remote control is by-

passed.

The “ ” position is for operating

the unit with the provided remote

control. When in this position

the unit is operated with the ON

and OFF buttons of the remote

control.

When the switch is in the center

“ O” position the unit is off.

B. Heater On/Off Switch

The Heater On/Off Switch

supplies power to the heater

Operation

3-Position Switch to Off (“O”) and

waiting ve (5) minutes before

switching the unit back on.

CAUTION: If you need to

continuously reset the heater,

unplug the unit and call

Customer Service at

1-888-346-7539.

Remote Operation

The Compact Stove is supplied

with an integrated On/Off remote

control.

!NOTE: Ensure that the

stove's 3-Position Switch is set

to the remote Control setting

(“ ” position).

!NOTE: Before attempting any

operation with the remote, pull

the plastic insulator strip out from

between the remote casing and

battery cover (Figure 2).

To operate, push the ON button

to turn stove on, push the OFF

button to turn the stove off.

Remote Initialization/

Reprogramming

In the event that your remote

control ceases to operate your

replace, follow these steps to

re-initialize the remote control and

the remote control receiver in the

replace:

Place the1. 3-Position Switch

(Figure 1A) in the OFF (“O”)

position.

Wait a minimum of ve (5) 2.

seconds and then place the

3-Position Switch in the

Remote Control (“ ”) position.

Within3. 10 seconds of

changing the switch position,

press the ON button located

on the remote control

(Figure 2).

This will synchronize the remote

control and the replace receiver.

!NOTE: You will have only 10

seconds to perform this last

step. Failure to do so will result

in these steps needing to be

followed again.

Figure 2

Off Button

Button

Battery

Cover

Plastic

Strip

Close the battery cover.3.

Battery must be recycled

or disposed of properly.

Check with your Local

Authority or Retailer for recycling

advice in your area.

 WARNING: Disconnect

power before attempting any

maintenance or cleaning to

reduce the risk of re, electric

shock or damage to persons.

Helpful Hints: It is a good idea to

replace all light bulbs at one time

if they are close to the end of their

rated life. Group replacement will

reduce the number of times you

need to open the unit to replace

light bulbs.

Light Bulb Replacement

Allow at least ve (5) minutes for

the light bulbs to cool off before

touching to avoid accidental

burning of the skin. Light bulbs

needs to be replaced when you

notice a dark section of the ame

or when the clarity and detail of

Maintenance

the log exterior disappears.

There are two (2) bulbs located

under the Log Set which generate

the ames and embers.

Tools Required: Phillips

screwdriver

Light Bulb Requirements

Quantity of two (2) clear

chandelier or candelabra bulbs

with an E-12 (small) socket base,

and 25 Watt rating.

To Replace the Light Bulbs

① Remove the ve (5) screws

from the access panel, located on

the back of the unit, and remove

access panel (Figure 3).

② Locate and examine the bulbs

to determine if replacement is

required.

Operation

Battery Replacement

Slide battery cover open on1.

the remote control (Figure 2).

Correctly install one (1) 122.

Volt (A23) battery in the

battery holder.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Dimplex Stufa

Dimplex

Dimplex Bayport BYP20 Manuale di istruzioni

Dimplex

Dimplex Optiflame Cassia Noir RTOFSTV20 Manuale di istruzioni

Dimplex

Dimplex Langbrook LBK5SE Manuale utente

Dimplex

Dimplex DMCS13R Manuale utente

Dimplex

Dimplex Brayford BFD20 Manuale utente

Dimplex

Dimplex DCS19W Manuale utente

Dimplex

Dimplex STOCKBRIDGE SKG20BL Manuale utente

Dimplex

Dimplex Optiflame 3D Laverton LVT20 Manuale di istruzioni

Dimplex

Dimplex Willowbrook WLL20-INT Manuale utente

Dimplex

Dimplex Piermont PMN20 Manuale utente

Dimplex

Dimplex Opti-myst Evandale Slate EVN20SL Manuale di istruzioni

Dimplex

Dimplex Optiflame Leckford LEC20 Manuale di istruzioni

Dimplex

Dimplex ELECTRALOG CS1205 Manuale utente

Dimplex

Dimplex OPTIMYST FORTROSE FOR20 Manuale utente

Dimplex

Dimplex CELESTE Manuale utente

Dimplex

Dimplex DS2205 Manuale utente

Dimplex

Dimplex ELECTRIC STOVE Manuale utente

Dimplex

Dimplex OPTIMYST RTOPSTV20 Manuale utente

Dimplex

Dimplex Noir RTOPSTV20GN Manuale utente

Dimplex

Dimplex ROTHESAY RSY20BR Manuale utente

Dimplex

Dimplex Stockbridge SKG20BL Manuale di istruzioni

Dimplex

Dimplex ELECTRALOG CS2307 Manuale utente

Dimplex

Dimplex COURCHEVEL CVL20E Manuale di istruzioni

Dimplex

Dimplex DS4411 Manuale utente

Manuali Stufa popolari di altre marche

Arada

Arada Cassette Stove Manuale utente

Parmco

Parmco FS 600 Manuale utente

MCZ

MCZ SUITE AIR 10 M2 Manuale utente

HearthStone

HearthStone Stowe DV 8321 Guida alla risoluzione dei problemi

Cattara

Cattara FAMILY Manuale utente

Stanley

Stanley Argon F500 OVAL Manuale utente

Avalon

Avalon B-VENT Manuale utente

Nordpeis

Nordpeis Vega Manuale utente

Exquisit

Exquisit EKC601-5 Manuale operativo

Stanley

Stanley Oisin Oil MK II Manuale del proprietario

Thermocet

Thermocet Brookfield S/CC Manuale utente

HASE

HASE delhi Manuale utente

Vermont Castings

Vermont Castings Intrepid 2 Manuale utente

Italiana Camini

Italiana Camini CLASSICA Guida rapida

Avalon

Avalon Vashon Avanti DVS FS Manuale utente

Spartherm

Spartherm ambiente a1 Manuale utente

Warmlite

Warmlite WL46040 Manuale utente

Regency

Regency Ultimate U39E Series Guida rapida