Directed Electronics VSM200 Manuale utente

+12V

GND

Fuse D2D (4 pin, wht)

ESP (3 pin, blk)

ESP (4 pin, brn)

2 pin

4 pin

+12V

GND

D2D

(4 pin, white)

2 pin

4 pin

cut loop (see table)

✂

CPU1

NOTE: The appearance and connector/port arrangement on the

Directed/Avital/Xpresskit system may dier to the examples shown .

SmartStart Module

(Top view)

SmartStart Module to Xpresskit

Directed System

(Top view)

LED

Installation Procedure

This product is compatible with all Directed Electron-

ics Security, Remote Start and hybrid systems that are

ESP2 compatible (3 or 4-pin).

CAUTIONS

The white plug is ONLY for RSR (Remote Start

Ready) applications

For systems with combined 4-pin ESP/D2D ports,

you CANNOT use an interface module in D2D

mode when using a SmartStart module. You must

use W2W on the bypass module

There should NEVER be more than one data plug

connected from the 3-way harness

DO NOT cut any of the loops on the SmartStart

Module (unless used for RSR applications)

DO NOT connect the black 3-pin ESP connector to

white Door Lock port on Directed systems

Please read the following before proceeding

1. Customer Information required:

• Record the customer information requested

in step 5a of this procedure. The module ID

# is provided on a sticker which can be af-

ﬁxed to the space provided in step 5a.

• Is this a new account or one being added to

an existing account? Check box(es) in 5a.

This information is required for ﬁnal veriﬁ-

cation/activation of the VSM200/250 or

DSM200/250.

2. Installation Points:

• Install and test the security/remote start sys-

tem ﬁrst using the associated guides and

wiring diagram. If using an existing system,

verify it is fully functional before installing the

Directed SmartStart module.

• For 3000-series Remote Start systems with

no supplied remote control, test the installed

system using the functional commands in the

SmartStart activation portal.

• Mount the SmartStart module as high as pos-

sible in the vehicle (side with color label and

model number facing down). Mount with

minimal obstructions that can affect commu-

nications and within reach of the main Di-

rected system using the provided cables (do

not extend).

• DO NOT connect the SmartStart module un-

til the ﬁnal programming of the Remote Start

main unit and veriﬁcation of security/remote

start system operations are completed.

QRNDSM250 2011-05

Signal Strength (RSSI)

The module's signal strength (RSSI) can be viewed in the

activation portal after a successful transmission test. This ﬁeld is

displayed on the webpage as "RSSI: XX dB" with XX being the

numeric variable. Use the range guide (at right) to determine

the signal strength. Monitor this signal during installation to

ensure the device is mounted in a location which maximizes

signal strength with minimal interference.

GPS location accuracy should also be checked on the activa-

tion portal when activating DSM/VSM250 modules.

Quick Reference

Install Guide

VSM200/250, DSM200/250

-50 to -90 dB

-91 to -100 dB

> -100 dB

= good signal strength

= borderline/inconsistent signal strength

= weak, insufﬁcient signal strength

Wiring Schematic

3. Install the VSM200/250 or DSM200/250 using

the information in the wiring diagram and steps

(Note CAUTIONS during installation).

a. Complete the main power connections.

b. Connect the 4-pin extension cable to the

SmartStart module cable.

c. Connect the interface cable to the extension

cable and the other appropriate end into the

Bitwriter port of the Directed system.

d. When power is connected, the module be-

gins an initialization procedure that may

take several minutes. During this procedure,

progress is reported via the ﬂashing Amber/

Green LEDs next to the module cable. When

both LEDs turn on solid, the initialization pro-

cedure is completed (See Status LEDs for a

description of the various LED states).

Note: If the system does not include a remote control,

skip step 4 and proceed to step 5.

4. Re-verify security/remote start system operation:

Perform all basic operations such as Lock, Unlock,

Panic and Remote Start, (Trunk release where ap-

plicable) using the supplied remote control. If the

system operates as expected proceed to the next

step (5). If the system does not operate as ex-

pected, rectify the problem ﬁrst.

5. Verify and Activate the SmartStart module:

The following steps need to be performed for the

Veriﬁcation/Activation of the Directed SmartStart

module.

a. Collect Customer Information:

Customer's Full Name:

Customer's E-mail Address:

Customer's mobile phone # and phone carrier

Record/place Module ID # here:

New Account: Existing Account:

If this is an existing account, are you:

adding a new system:

or replacing an existing one:

b. Log on to: www.directechs.com, and click on

the SmartStart link.

c. Follow the on-screen directions to activate

and test a SmartStart device. If this is the cus-

tomer's ﬁrst SmartStart system, you will be

prompted to enter their information as col-

lected in step 5a.

d. Test the SmartStart system from the website

using the supplied function links.

e. The customer is sent log-in information for

the new Customer Service Portal via e-mail.

From there, they must provide the required

information. Once completed, the installed

system and account are activated. The cus-

tomer can then open the phone app and be-

gin using the service.

Status LEDs

Amber LED states:

• Off: No cellular communication. Check

connections such as module harness.

• Flashing slowly: The module is seeking

cellular system communication.

If no cell coverage is available the Amber

LED continues to ﬂash slowly, move the

vehicle to a location with better reception.

• Flashing quickly: The module is negotiat-

ing with a cellular system.

• On solid: Communication successfully es-

tablished.

Green LED states:

• Off: Communication not established with

the remote start main unit.

Check connection at the Bitwriter port,

once connected properly the LED turns

on.

• Flashing: Active communication in prog-

ress between the SmartStart module and

Remote Start main unit.

• On solid: Communication successfully es-

tablished with the remote start main unit.

Please return this guide and point the customer to

step 5e after successfully completing the installation

as it contains details required for account setup.

Notes: SmartStart response time can vary depend-

ing on cellular coverage and network congestion.

Operating temperature range: -30°C to + 70°C.

Additional information

can be found at:

www.directechs.com

Logo, Directed Electronics w-driven.eps

Logo, Directed with designed in USA.eps

Logo, Directed with Distributed By.eps

Directed Logo Usage

Questo manuale è adatto per i seguenti modelli

Altri manuali Directed Electronics Avviamento remoto

Directed Electronics

Directed Electronics Failsafe 103T Manuale utente

Directed Electronics

Directed Electronics AutoCommand 41026 Guida rapida

Directed Electronics

Directed Electronics SmartStart 5000-series Manuale utente

Directed Electronics

Directed Electronics Viper 5501 Manuale utente

Directed Electronics

Directed Electronics Valet 561R Manuale utente

Directed Electronics

Directed Electronics Valet 561T Manuale utente

Directed Electronics

Directed Electronics DB3 Manuale utente

Directed Electronics

Directed Electronics 50.7X Manuale utente

Directed Electronics

Directed Electronics AS-1775 Manuale utente

Directed Electronics

Directed Electronics 210HV Manuale utente

Directed Electronics

Directed Electronics 4400 Manuale utente

Directed Electronics

Directed Electronics ONE-WAY FM AUTOMATIC/MANUAL TRANSMISSION Manuale utente

Directed Electronics

Directed Electronics VIPER 5901 Manuale utente

Directed Electronics

Directed Electronics Viper Manuale utente

Directed Electronics

Directed Electronics AM6 Manuale utente

Directed Electronics

Directed Electronics PS-4661TWE-FM Manuale utente

Directed Electronics

Directed Electronics SmartStart 5000-series Manuale utente

Directed Electronics

Directed Electronics AutoCommand 41027T Guida rapida

Directed Electronics

Directed Electronics Nissan Guida rapida

Directed Electronics

Directed Electronics 410 Manuale utente

Directed Electronics

Directed Electronics Xpresskit CANMAX400 Manuale utente

Directed Electronics

Directed Electronics READY REMOTE 24923 Manuale utente

Directed Electronics

Directed Electronics AutoCommand 28624T Manuale utente

Directed Electronics

Directed Electronics Xpresskit Xpressparts Series Manuale utente

Manuali Avviamento remoto popolari di altre marche

AstroStart

AstroStart 803U Manuale utente

Durite

Durite 0-649-20 Manuale

EINHELL

EINHELL BT-PS 1000 Manuale

Linear

Linear ACCESS AK-21 Specifiche tecniche

Soundstream

Soundstream TARANTULA RS.2 Manuale utente

Jaycar Electronics

Jaycar Electronics MB3752 Manuale utente

Ultra Start

Ultra Start 72 Series Manuale utente

ADS

ADS FLASHLOGIC FLRSVW1 Manuale utente

Selecta

Selecta JS012 Manuale utente

Black Widow Security

Black Widow Security BW RAS 400 Manuale utente

Vector

Vector Power City DK080706 Supplemento

Code Alarm

Code Alarm CA-535 Manuale utente

Ozito

Ozito OJS-800 Manuale utente

Profi-Partner

Profi-Partner 46387 Manuale utente

EZ STARTER

EZ STARTER EZ-45 Manuale utente

Viper

Viper 4204 Manuale utente

Essex Electronics

Essex Electronics KE-1701 Manuale utente

EINHELL

EINHELL EGS 3600 Manuale