Directed DS4+ Manuale utente

INSTALLATION GUIDE

DS4+

2010 Toyota Camry (Smart Key). 933.TL1 5.03.185

This product is intended for installation by a professional installer only! Attempts to install this

product by a person other than a trained professional may result in severe damage to a vehicle’s

electrical system and components.

Introduction 4

Vehicle function compatibilities 4

Pre-installation and application warnings 5

OEM remote starter detection 6

Wiring diagram 7

Locating components in the vehicle 8

Vehicle connections 9

Connecting the module 12

Important! 12

RF Systems 12

8556T Temperature Sensor 12

8504D Combo Sensor 12

When used in conjunction with SmartStart 12

D2D port configuration 13

Module programming 14

LED diagnostics and troubleshooting 15

Soft reset 17

Hard reset 17

Learning the Tach (not needed with Virtual Tach) 18

Initializing Virtual Tach (not needed with hardwired or data tach applications) 18

Limited lifetime consumer warranty 19

Quick reference guide 20

Contents

3933.TL1 5.03.185 2010 Toyota Camry (Smart Key)

Warning! Safety ﬁrst

The following safety warnings must be observed at all times:

• Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer.

• When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never

operate the system in an area that does not have adequate ventilation.

The following precautions are the sole responsibility of the user; however, authorized Directed dealers should:

• Never use a test light or logic probe when installing this unit. Always use a multimeter.

• Never operate the system in an enclosed or partially enclosed area without ventilation (such as a garage).

• USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE.

ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE

STORAGE AREA MUST REMAIN CLOSED AT ALL TIMES.

Use of this product in a manner contrary to its intended mode of operation may result in property damage, personal injury, or

death. Except when performing the Safety Check outlined in this installation guide, (1) Never remotely start the vehicle with

the vehicle in gear, and (2) Never remotely start the vehicle with the keys in the ignition. The user is responsible for having the

neutral safety feature of the vehicle periodically checked, wherein the vehicle must not remotely start while the car is in gear.

This testing should be performed by an authorized Directed dealer in accordance with the Safety Check outlined in this product

installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult with the user to ﬁx the problem

immediately.

OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF

OPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE

OR PERSONAL INJURY. IMMEDIATELY CEASE THE USE OF THE UNIT AND REPAIR OR DISCONNECT THE INSTALLED REMOTE

START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS.

Remote starters for manual transmission pose signiﬁcant risks if not properly installed and operated. When testing to ensure the

installation is working properly, only remote start the vehicle in neutral gear, on a ﬂat surface and with a functional, fully engaged

parking brake. Do not allow anyone to stand in front of or behind the vehicle.

This product should not be installed in any convertible vehicles, soft or hard top with a manual transmission. Installation in such

vehicles may pose certain risk.

4933.TL1 5.03.185 2010 Toyota Camry (Smart Key)

Introduction

DS4+ is a complete solution for remote start, security (when security features are enabled), bypass, and features

built in Bluetooth 4.0 allowing you to conﬁgure and control your system. This guide provides information

on the installation of the module as an analog unit, however a digital solution could be available for your

vehicle. Please refer to the DirectLink application or www.directechs.com for more information about which

conﬁguration is best for your application.

Warning! This module is designed to be conﬁgured using the DirectLink application for mobile devices, however it can also

be conﬁgured using the web tool located at www.directechs.com. To download the DirectLink mobile application, please visit the

Google Play or Apple store.

Vehicle function compatibilities

This section lists all the functions compatible with this vehicle for the installation illustrated in this guide.

Arm Factory Security

Disarm Factory Security

Door Lock Control

Door Unlock

Driver Priority Unlock

Trunk / Hatch Release

Immobilizer Bypass-Data No Key Req'd

3x LOCK START (Start control using OEM Remote)

Accessory Activation

Ignition Activation

SmartStart

Start (Crank) Activation

Tach / RPM Output

Entry Monitoring ALL Door Pins

Entry Monitoring Hood Pin

Entry Monitoring Trunk/Hatch Pin

Factory Alarm Trigger Monitoring

Brake Status (foot brake)

E-Brake Status

Ignition Status

5933.TL1 5.03.185 2010 Toyota Camry (Smart Key)

Pre-installation and application warnings

Firmware notes: This section highlights important information for this speciﬁc ﬁrmware and will assist in

pricing accordingly, as well as bringing awareness to any operational or vehicle limitations.

T-Harness

compatible

Keys required for

programming 1Keys required for

operation 0

No takeover feature is available on Push-to-Start vehicles. The vehicle will shut down as soon as a door is opened.

To remote start the engine, the hood, hatch, and all doors MUST be closed.

Keyless and Smart Key will remain functional during remote start.

All connectors are displayed from the wire side (unless speciﬁed otherwise).

It is important to check that the fuses are positioned correctly in the module. Proper fuse positioning is displayed on each

wiring diagram.

Refer to the "Vehicle connections" following the installation diagram.

General notes: This section highlights important information for this speciﬁc ﬁrmware.

[1] The installation of an aftermarket hood pin is ONLY required on vehicles that are NOT equipped with a factory hood pin.

[2] The siren is ONLY required when enabling the security features during module ﬂashing.

[3] Autolights Interrupt ONLY required if vehicles are equipped with Autolights.

[4] Connection required ONLY if Pit Stop/Idle mode is desired.

6933.TL1 5.03.185 2010 Toyota Camry (Smart Key)

OEM remote starter detection

How to know if the vehicle is equipped with an OEM remote starter

1. An “ENGINE STARTER”

sticker should be on the remote.

ENGI NE

STARTER

2. Remote start the OEM remote starter:

Press the remote control’s lock button twice within 2 seconds, then press and hold the lock

button for 3 seconds.

x2 &Press & Hold

for 3 seconds

The parking lights ﬂash after 3 seconds. The engine starts and the parking lights ﬂash

repeatedly for 20 seconds.

If the vehicle is equipped with an add-on Lexus/Toyota OEM remote starter

The factory remote starter must be permanently disconnected before programming the Directed interface as both modules cannot

coexist. See "Locating the OEM Remote Starter" below.

Locating the OEM Remote Starter

Vehicle OEM Remote Starter & Connector Location

Toyota Camry (Smart Key) 2007-2011 Behind Glove Box & Passenger kick panel.

Toyota Camry Hybrid (Smart Key) 2007-2011 Behind Glove Box & Passenger kick panel.

Toyota Corolla (Smart Key) 2009-2013 Behind Glove Box & Passenger kick panel & Junction Box & Steering column.

Toyota Highlander (Smart Key) 2008-2013 Behind Glove Box & Passenger kick panel.

Toyota Highlander Hybrid (Smart Key) 2008-2013 Behind Glove Box & Passenger kick panel.

Toyota Rav4 (Smart Key) 2009-2012 Behind Glove Box & Junction Box.

7933.TL1 5.03.185 2010 Toyota Camry (Smart Key)

Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).

(+) 12V Input: Blue/Red: 2

(-) Ground: Black: 10

HS CAN Low: Tan: 1

(-) Parking Light Output: Lt.Green/Black: 1

(-) Push-to-Start Output: Lt.Blue/Black: 10

HS CAN High: Tan/Black: 2

Siren

Hood Pin

(+) 12V Input: Red: 6 &12

Autolights Interrupt (veh. side): Lt.Green: 8

Autolights Interrupt (conn. side): Lt.Green/White: 9

(+) Start Stop Switch Output: Blue: 3

(-) Hood Input: Gray: 21

(+) Siren Output: Brown/Red: 11

OBDII

Diagnostic

Connector

(-) Parking Lights:

Black or Lt. Blue, pin 18

(+) 12V,

Black or White,

pin 1

(+) STSW: Pin 4 or 6

12345678910

1112131415161720

1543 1

811

12 10 9

ENGINE

START

STOP 7

(-) Push-To-Start:

Blue or Pink, pin 7

PTS Switch

(black conn.

behind PTS button)

Headlight Switch

(white conn.

at headlight switch)

Main Body ECU

(white conn.

under drivers dash)

Dash Fuse Box

(white conn.)

Autolight:

Green or Yellow, pin 19

CUT

HS CAN Low: Pin 14

HS CAN High: Pin 6

22 810 12

4 2442

DS4+

DS4

Slide

to open

Proper Fuse

Positioning

DS4+ DS4

MAIN (5A) (+)

(-) RLY3 PK LIGHT (15A) (+)

(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)

(-) RLY3/PK LIGHT(15A) (+)

It is important to check that the

fuses are positioned correctly.

10 9 8

6543

2 1

Wiring diagram

8933.TL1 5.03.185 2010 Toyota Camry (Smart Key)

Locating components in the vehicle

9933.TL1 5.03.185 2010 Toyota Camry (Smart Key)

Vehicle connections

The connection information listed below is specific to the 2010 Toyota Camry (Smart Key). Refer to “Pre-installation and application warnings” for a list of important notes.

Main harness, 12-pin black connector (H1)

Module Connects To

Conn./Pin Color Description Wire Location (+/-) Wire Color Ref.

H1/1 Blue/White Relay N.C. No Connection No Connection

H1/2 Blue/Red Relay N.O. STSW Body ECU on back of dash fuse box, white 10 pin plug, pin 4 + gray

H1/3 Blue Relay COM STSW dash fuse box, white 1 pin plug (A), pin 1 + black (120A)

H1/4 White/Brown Relay N.C. No Connection No Connection

H1/5 White Relay COM Clutch Activation Output clutch switch, black 2 pin plug, pins 1 and 2 +

N.O. red (in), green (out)

H1/6 Red No Connection No Connection

H1/7 Lt. Green/Red Relay N.O. No Connection No Connection

H1/8 Lt. Green Relay COM Auto Light headlight switch, white 20 pin plug, pin 19 cut green

H1/9 Lt. Green/White Relay N.C. Auto Light headlight switch, white 20 pin plug, pin 19 cut green

H1/10 Black No Connection No Connection

H1/11 White Relay COM No Connection No Connection

H1/12 Red No Connection No Connection

Relay harness, 10-pin white connector (H2)

Module Connects To

Conn./Pin Color Description Wire Location (+/-) Wire Color Ref.

H2/1 N/A No Connection No Connection

H2/2 Red/Black No Connection No Connection

H2/3 Pink/Black No Connection No Connection

H2/4 Pink/White No Connection No Connection

H2/5 Red No Connection No Connection

H2/6 Green No Connection No Connection

H2/7 Violet No Connection No Connection

H2/8 Orange No Connection No Connection

H2/9 Red/White No Connection No Connection

H2/10 Pink No Connection No Connection

Data harness, 8-pin white connector (H3)

Module Connects To

Conn./Pin Color Description Wire Location (+/-) Wire Color Ref.

H3/1 Tan (Data) HS CAN Low data link connector, black 16 pin plug, pin 14 data white

H3/2 Tan/Black (Data) HS CAN High data link connector, black 16 pin plug, pin 6 data black

H3/3 Orange/Brown No Connection No Connection

H3/4 Orange/Green No Connection No Connection

10 933.TL1 5.03.185 2010 Toyota Camry (Smart Key)

Module Connects To

Conn./Pin Color Description Wire Location (+/-) Wire Color Ref.

H3/5 Lt. Green No Connection No Connection

H3/6 Violet/Brown No Connection No Connection

H3/7 Orange/Black No Connection No Connection

H3/8 Yellow/Black No Connection No Connection

Analog input/output harness, 22-pin white connector (H4)

Module Connects To

Conn./Pin Color Description Wire Location (+/-) Wire Color Ref.

H4/1 Lt. Green/Black (-) Pk Light Output headlight switch, white 20 pin plug, pin 18 - black

H4/2 Blue/White No Connection No Connection

H4/3 Dk. Green/Black No Connection No Connection

H4/4 Red/White No Connection No Connection

H4/5 Brown/Black No Connection No Connection

H4/6 Brown/White No Connection No Connection

H4/7 White (+) No Connection No Connection

H4/8 Violet/Black No Connection No Connection

H4/9 Dk. Blue/Black No Connection No Connection

H4/10 Lt. Blue/Black (-) PTS engine start stop switch, black or gray 14 pin plug, pin 7 - blue

H4/11 Brown/Red No Connection No Connection

H4/12 Pink No Connection No Connection

H4/13 Violet No Connection No Connection

H4/14 Brown No Connection No Connection

H4/15 White/Blue No Connection No Connection

H4/16 Red/Blue No Connection No Connection

H4/17 Black/White No Connection No Connection

H4/18 Orange/Black No Connection No Connection

H4/19 Blue No Connection No Connection

H4/20 Green No Connection No Connection

H4/21 Gray (-) Hood Switch Input

H4/22 Violet/White No Connection No Connection

Altri manuali per DS4+

Indice

Altri manuali Directed Avviamento remoto

Directed

Directed Xpresskit DBALL2 Manuale utente

Directed

Directed 3000 series Manuale utente

Directed

Directed Viper 5706V Manuale utente

Directed

Directed SMARTSTART ASRA-2510 Manuale utente

Directed

Directed PS-3655EFM Manuale utente

Directed

Directed Autostart Signature Series Manuale utente

Directed

Directed Xpresskit DBALL2 Manuale utente

Directed

Directed 5906 Manuale utente

Directed

Directed XPRESSSTART ONE Guida all'installazione

Directed

Directed AstroStart RS-625 Manuale utente

Directed

Directed XpressSTART Mercedes Solution Manuale utente

Directed

Directed SmartStart 5000 Series Manuale utente

Directed

Directed DS4+ Manuale utente

Directed

Directed Directechs DB3 Manuale utente

Directed

Directed AS-1774 Manuale utente

Directed

Directed SMARTASTART VSM300 Manuale utente

Directed

Directed Python 4105P Manuale utente

Directed

Directed PS-3180E Manuale utente

Directed

Directed Smart Start ASRF-1510 Manuale utente

Directed

Directed TWO -WAY FM LED AUTOMATIC/MANUAL TRANSMISSION REMOTE... Manuale utente

Directed

Directed Clifford 4606X Manuale utente

Directed

Directed Clifford 4706X Manuale utente

Directed

Directed 4113, 1-button series Manuale utente

Directed

Directed Xpresskit DBALL2 Manuale utente

Manuali Avviamento remoto popolari di altre marche

AstroStart

AstroStart 803U Manuale utente

Durite

Durite 0-649-20 Manuale

EINHELL

EINHELL BT-PS 1000 Manuale

Linear

Linear ACCESS AK-21 Specifiche tecniche

Soundstream

Soundstream TARANTULA RS.2 Manuale utente

Jaycar Electronics

Jaycar Electronics MB3752 Manuale utente

Ultra Start

Ultra Start 72 Series Manuale utente

ADS

ADS FLASHLOGIC FLRSVW1 Manuale utente

Selecta

Selecta JS012 Manuale utente

Black Widow Security

Black Widow Security BW RAS 400 Manuale utente

Vector

Vector Power City DK080706 Supplemento

Code Alarm

Code Alarm CA-535 Manuale utente

Ozito

Ozito OJS-800 Manuale utente

Profi-Partner

Profi-Partner 46387 Manuale utente

EZ STARTER

EZ STARTER EZ-45 Manuale utente

Viper

Viper 4204 Manuale utente

Essex Electronics

Essex Electronics KE-1701 Manuale utente

EINHELL

EINHELL EGS 3600 Manuale