Dish Network HM-DSR100RU Manuale utente
DISH Network
EZ Remote Control
User Guide
SELECT
POWER
GUIDE
SAT TV
CHANNEL
CONTROL
T
H
E
M
E
B
R
O
W
S
E
C
H
A
N
N
E
L
C
H
A
N
N
E
L
INFO VOL
CANCEL
123
456
789
0
RECALL MUTE
118866 1
CONTENTS OF THIS GUIDE
About the DISH Network EZ Remote Control................... 3
Buttons and Features Overview........................................ 3
Installing Batteries.............................................................. 4
Receiver Upgrade ............................................................... 5
SettingUp toSwitchtheTVto
Watch Satellite Programming......................................... 5
Connecting Your Satellite Receiver and TV ............... 6
Setting Up the Remote to Control Your TV ................ 7
Setting Up on Your Remote Control .................... 8
SettingUp toSwitchtheTVtoa
Preferred Off-Air Channel .............................................. 12
Connecting an Off-Air Antenna to Your
Satellite Receiver.................................................... 12
Setting Up on the Remote Control...................... 13
SettingUp toPassSatellite
Programming Through Your VCR to Your TV.............. 14
Connecting Your Satellite Receiver, VCR,
and TV.................................................................... 15
Setting Up the Remote to Control Your VCR ........... 16
Setting Up on Your Remote Control .................. 17
Using When a VCR is Installed................................... 20
Other Remote Control Instructions.................................. 21
How to Scan for TV Codes....................................... 21
How to Scan for VCR Codes.................................... 22
How to Check the TV Codes .................................... 23
How to Check the VCR Codes ................................. 23
How to Remove TV Codes....................................... 24
How to Remove VCR Codes.................................... 24
How to Use the Remote Control....................................... 25
Pointing the Remote Control .................................... 25
Using the Remote Control for
Satellite TV Programming....................................... 25
Using the Remote Control for
Off-Air TV Programming .........................................30
TV and VCR Codes ........................................................... 32
TV Codes.................................................................. 32
VCR Codes............................................................... 39
Limited Warranty ............................................................... 45
118866 3
ABOUT THE DISH NETWORK EZ REMOTE
CONTROL
The DISH Network EZ Remote Control makes operating
your DISH Network satellite receiver easy and
convenient. This remote control includes large, easy-to-
find buttons which are most commonly used to control the
basic satellite receiver features you need. In addition, the
DISH Network EZ Remote Control lets you switch
between satellite receiver programmingand programming
from an off-air antenna with the press of one button.
BUTTONS AND FEATURES OVERVIEW
Figure 1 on page 2 briefly describes each button on the
DISH Network EZ Remote Control. Most of these buttons
work the same way as the buttons on other DISH Network
remote controls. See the User’s Guide for your DISH
Network satellite receiver for a description of how your
satellite receiver works with these buttons.
There are some added buttons on this remote control to
make operation with your TV easier. These buttons are:
SATELLITE CHANNEL CONTROL - Press to switch
your TV to watch programming from your satellite
receiver.
OFF-AIR CHANNEL CONTROL - Press to switch your
TV to watch programming from your off-air antenna.
TV POWER- Press to turn your TV on or off.
TV
4 118866
To use these added buttons and other features to control
your TV, follow the step-by-step instructions below to set
up your remote control. This setup also requires you to
connect your satellite receiver to your TV’s tuner using
coaxial cable. After completing your setup, see How to
Use the Remote Control on page 25 for more details on
each button.
INSTALLING BATTERIES
Before you can use the remote control, you must install
four AAA batteries. Use batteries of the same grade, for
example, alkaline or carbon zinc, and do not mix different
grades. Alkaline batteries provide longer battery life.
1. Press down on the arrow on the battery cover and
slide off the cover.
2. Insert the new batteries, making sure that the ends
marked “+” are installed as shown inside the battery
compartment.
3. Replace the battery cover by sliding the cover back
into place.
CLOSE
OPEN
118866 5
RECEIVER UPGRADE
6 118866
CONNECTING YOUR SATELLITE RECEIVER AND TV
Figure 2. Connect the Satellite Receiver and TV
1. Connect a coaxial cable between the TV Set Out on
the satellite receiver and the tuner input on the TV
(see Figure 2).
Note: If you connect your TV a different way (for
example, using yellow, red, and white audio/video
RCA-type or S-Video cables), the feature to switch
your TV to satellite programming using will
not work.
2. Set on the back of the receiver to CH3.
Note: If you prefer Channel 4, instructions are
provided later to change this setting.
Note: If your satellite receiver does not have a ,
see your satellite receiver’s User’s Guide for how
to set TV Set Out on the satellite receiver to
Channel 3.
Step 2
Step 1
118866 7
SETTING UPTHEREMOTE TO CONTROL YOUR TV
1. Find the brand name of your TV in the TV code
tables starting on page 32. You will be referring to
this location for codes in the instructions below.
2. Turn on your TV.
3. Press and hold until both lights turn
on (it takes about five seconds).
4. Release . light will flash.
5. Press . Notice light turns on and stays on.
6. Enter one of the three-digit codes for your TV from
the TV code tables while light is on.
Note: You have about 20 seconds to begin entering
the TV code.
7. Press the MUTE button and watch light.
If light flashes three times, the code is valid
and you can go to step 8. If light does not flash
at all, the code may not have been entered
correctly. So, start over from step 3 and try the code
again.
8. Press and your TV should shut off. If your TV
shuts off, go to step 9. If not, pick another code for
your TV brand from the TV Codes table and go
back to step 3. If you have tried all of the codes and
none work, go to How to Scan for TV and VCR
Codes on page 21.
9. Turn your TV back on by pressing again and
try the other buttons below to make sure they work.
•Press the 0through 9buttons to change channels
on your TV.
SAT TV
TV
TV TV
TV
TV
TV
TV
TV
TV
8 118866
SETTING UPONYOUR REMOTE CONTROL
•Press and to change channels on
your TV.
•Press to change the TV volume.
If these buttons work, go on to the next section to
set up . If not, pick another code for your TV
brandfromtheTVCodestableandgobackto
step 3.
1. Make sure your TV and satellite receiver are
connected and your remote control is set up to
control your TV using the instructions in the last
two sections.
2. Turn on your TV and tune to a channel other than 3
(for example, 4 or 5).
3. Press and your satellite receiver should turn on
and your TV should tune to Channel 3.
4. Press the MENU button. If you see the satellite
receiver Menu screen,gotostep5.Ifnot,goto
step 15.
5. If you want to keep your satellite programming on
TV Channel 3, check the box below and go to step
28. 3
6. If you prefer to have your satellite programming on
TVChannel4,goontostep7.
VOLVOL
118866 9
7. Set the switch on the back of the satellite
receiver to CH4. The TV will lose the picture from
the satellite receiver, but this is OK.
Note: If your satellite receiver does not have a
switch, see your satellite receiver’s User’s Guide
for how to set TV Set Out on the satellite receiver to
channel 4.
8. Press and hold until both lights turn
on (it takes about five seconds).
9. Release . light will flash.
10.Enter 0-4.
11.Press MUTE while watching light.
12. light will flash three times.
If the light does not flash at all, repeat this
procedure starting with step 8.
13.Press while watching your TV. If your TV
tunes to Channel 4, go to step 14. If not, go to
step 7.
14.Press the MENU button. If you see the satellite
receiver Menu screen, check the box below and go
to step 28.
4
15. Answer the questions in Table 1. The information
you provide is what you will use to teach your
remote control to change the channel on your TV
correctly.
SAT TV
SAT
SAT
SAT
Indice
Altri manuali Dish Network Telecomando universale
Dish Network
Dish Network 167821 Manuale utente
Dish Network
Dish Network 811 Manuale utente
Dish Network
Dish Network ViP 211k Manuale utente
Dish Network
Dish Network 21.0 Manuale utente
Dish Network
Dish Network Platinum PVR Remote Control Manuale utente
Dish Network
Dish Network Blue Button 1.5 Manuale utente
Dish Network
Dish Network C-8 Manuale utente
Dish Network
Dish Network DISH 381 Manuale utente
Dish Network
Dish Network Dish 322 Manuale utente
