DiSS KE-8000MX Manuale utente

Digital Video

Surveillance System

Engineering Service Manual

The picture might differ according to the specification and model.※

Contents of this manual are protected under copyrights and computer program laws.※

First edition : 1 September 2007

Contents

1. HDD INSTALLATION..................................................................................................................................................1

1.1 HDD INSTALLATION....................................................................................................................................................1

1.2 HDD FORMAT............................................................................................................................................................2

1.3 RECOMMENDED HDD &BACKUP DEVICE (CD, DVD)..................................................................................................4

2. CONNECTING PERIPHERAL DEVICE & PIN ASSIGNMENT ..................................................................................5

2.1 CONNECTING PERIPHERAL DEVICE.............................................................................................................................5

2.2 PINASSIGNMENT ......................................................................................................................................................6

3. NETWORK CONFIGURE ...........................................................................................................................................7

3.1 FIXED PUBLIC IP........................................................................................................................................................7

3.2 DYNAMIC PUBLIC IP...................................................................................................................................................7

3.3 REMOTEMANAGER SETTING.....................................................................................................................................11

4. IR REMOTE CONTROLLER ....................................................................................................................................13

5. TO RESET THE ADMIN PASSWORD......................................................................................................................14

6. TO RESET ALL THE SETTING VALUE...................................................................................................................15

7. FIRMWARE UPGRADE............................................................................................................................................16

8. TO CHANGE MCU....................................................................................................................................................19

9. TO CHANGE VGA BOARD......................................................................................................................................22

10. TROUBLE SHOOTING.............................................................................................................................................25

10.1 SYSTEM................................................................................................................................................................25

10.2 LIVE &RECORDING..................................................................................................................................................25

10.3 OTHER ....................................................................................................................................................................25

11. FAQ ...........................................................................................................................................................................27

1. HDD Installation

1.1 HDD Installation

1. Setting up Master/Slave jumper of HDD.

2. Secure HDD to bracket using secure screw.

3. Attach HDD bracket to its body using HDD bracket secure screw.

4. Connect the data & power cable.

1.2 HDD Format

1.2.1. Single HDD

1.2.1.1. In case of Lower than 500GB (EX. 500GB)

1. Install the 500GB HDD to Primary Master.

2. Tick on the HDD check box. (ID No. 1)

3. Click the “FORMAT” button.

1.2.1.2. In case of Higher than 500GB (EX. 750GB)

1. Install the lower than 500GB HDD to Primary Master (ID No. 1).

2. Install the 750GB HDD to Primary Slave (ID No. 2).

3. Format the lower than 500GB HDD first, as like “1.2.1.1”.

4. Tick on the 750GB HDD (ID No. 2) and Click the “FORMAT” button.

5. Power Off and remove the all HDDs.

6. Install the 750GB HDD to Primary Master, which is formatted at “4”.

Note It takes around 2minutes for 250GB, 3minutes for 500GB, or 4minutes for 750GB each..

1.2.2. Multiple HDDs

1.2.2.1. In case of all HDDs are lower than 500GB (EX. 500GB)

1. Install the all HDDs to Primary Master, Primary Slave, Secondary Master and Secondary Slave.

2. Tick on the all HDDs check box. (ID No. 1 ~ 4)

3. Click the “FORMAT” button.

4. All HDDs will be formatted sequentially ID No. 1 to 4

1.2.2.2. In case of all HDDs are Higher than 500GB (EX. 750GB)

1. Install the lower than 500GB HDD to Primary Master (ID No. 1).

2. Install the 750GB HDD to Primary Slave (ID No. 2).

3. Format the lower than 500GB HDD first, as like “1.2.1.1”.

4. Tick on the 750GB HDD (ID No. 2) and Click the “FORMAT” button.

5. Power Off and remove the all HDDs.

6. Install the 750GB HDD (formatted at “4”) to Primary Master.

7. Install the others HDDs (750GB Each) to Primary Slave, Secondary Master and Secondary Slave.

8. Tick on the HDD Check box ID No. 2 to 4.

9. Click the “FORMAT” button.

10. All HDDs will be formatted sequentially ID No. 2 to 4.

Note The system always reserves maximum 5GB space in each built-in HDD to effectively utilize archiving memory.

Note Master HDD must be no larger than 500GB in format, while other slave HDDs are limitless in capacity each.

If user wants to format & install over 500GB HDD in the master HDD position, then user has to install & format

a lower-capacity of HDD(lower 500GB) first in the master position, and then later, install & format an

over-500GB HDD in slave position. Once after user formats both master HDD(lower 500GB) & slave HDD(over

500GB), then user can replace master HDD(lower 500GB) with slave HDD(over 500GB) to have larger HDD

capacity(over 500GB) in the master position.

1.3 Recommended HDD & Backup Device (CD, DVD)

1.3.1. HDD List

No. Manufacture Capacity (GB) RPM

1 80 7200

2 250 7200

3 500 7200

Western Digital

5 160 7200

6 320 7200

7 400 7200

8 500 7200

9 750 7200

Seagate

1.3.2. Backup Device List (CD, DVD)

Device Manufacture Model

LITE-ON SHOR-5239V

CD-RW

GSA-H42L

LG GSA-H42N

DVD +/- RW

Note Kinds of Supported DVD Media to Backup

- DVD-R (O)

- DVD+R (O)

- DVD-RW (X)

- DVD+RW (X)

2. Connecting Peripheral Device & PIN Assignment

2.1 Connecting Peripheral Device

This section describes how to efficiently hook up peripheral devices with the DVR.

Install the DVR on flat surface. If required, attach a rubber mount for installation. In case that 19-inch rack is used, it is

recommend to install the system on shelve and use 2.5~3U(1U=1.75 inch or 4.45 cm) space for proper ventilation

Note Install the system in location with good ventilation to prevent overheating.

Caution ※The layout of the rear panel on the DVR might differ according to the models.

※Depending on the grounding, the coaxial cable connecting to the camera has danger of electric shock.

Shut down power of the system completely (unplug the power cable) before connecting video cable to BNC

port.

2.2 PIN Assignment

Note [ 4 Ch and 8 Ch Model ]

No. Sensor No. Alarm No. PTZ

2 Sensor 1 7 Alarm 1 (+) 1 RS 485 D+

3 Sensor 2 8 Alarm 2 (+) 11 RS 485 D-

4 Sensor 3 9 Alarm 3 (+)

5 Sensor 4 10 Alarm 4 (+)

6 Sensor Ground (1~4) 17 Alarm 1 (-)

12 Sensor 5 18 Alarm 2 (-)

13 Sensor 6 19 Alarm 3 (-)

14 Sensor 7 20 Alarm 4 (-)

15 Sensor 8

16 Sensor Ground (5~8)

4 sensor※-inputs for 4 Ch model (Pin # 12~16 : Disabled), while 8 sensor-inputs for 8 Ch model.

[ 16 Ch Model ]

No. Sensor No. Alarm No. PTZ

2 Sensor 1 11 Alarm 1 (+) 1 RS 485 D+

3 Sensor 2 12 Alarm 2 (+) 15 RS 485 D-

4 Sensor 3 13 Alarm 3 (+)

5 Sensor 4 14 Alarm 4 (+)

6 Sensor 5 25 Alarm 1 (-)

7 Sensor 6 26 Alarm 2 (-)

8 Sensor 7 27 Alarm 3 (-)

9 Sensor 8 28 Alarm 4 (-)

10 Sensor Ground (1~8)

16 Sensor 9

17 Sensor 10

18 Sensor 11

19 Sensor 12

20 Sensor 13

21 Sensor 14

22 Sensor 15

23 Sensor 16

24 Sensor Ground (9~16)

1 2 3 4 5 6 7 8 9

11 12 13 14 15 16 17 18 19

1 2 3 4 5 6 7 8 9 10

15 16 17 18 19 20 21 22 23 24 25 26 27 28

11 12 13 14

3. Network Configure

3.1 Fixed Public IP

1) Set the network [Type] to LAN.

2) Enter the IP Address, provided by

the Internet Company.

Note Incase network cannot be connected after completing the settings, try connecting the cable to another PC. This

it to check if the network (internet) connection is working properly.

3.2 Dynamic Public IP

3.2.1. Incase only xDSL modem is used without Router

Note Does not support PPPoE modem

Indice

Manuali Sistema di sicurezza popolari di altre marche

Inner Range

Inner Range Concept 2000 Manuale utente

Climax

Climax Mobile Lite R32 Istruzioni per il montaggio

CADDX

CADDX NX-6 Manuale utente

FBII

FBII XL-31 Series Manuale utente

Johnson Controls

Johnson Controls PENN Connected PC10 Manuale utente

Aeotec

Aeotec Siren Gen5 Manuale utente

Blaupunkt

Blaupunkt SA 2700 Manuale utente

IDEAL

IDEAL Accenta Manuale del proprietario

AJAX

AJAX DoubleButton Manuale utente

Swann

Swann SW-P-MC2 Manuale utente

Ecolink

Ecolink Siren+Chime Manuale utente

Digital Monitoring Products

Digital Monitoring Products XR150 Manuale utente

EDM

EDM Solution 6+6 Wireless-AE Manuale utente

Highway Safety Group

Highway Safety Group EA401 Manuale utente

Siren

Siren LED GSM Manuale utente

Detection Systems

Detection Systems 7090i Istruzioni per il montaggio

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuale utente

Siemens

Siemens FDM273 Manuale utente