Dixie Narco 90 Series Istruzioni per il montaggio

INSTALLATION AND SET-UP GUIDE

SERIES 90 VENDERS

903,901,600.21

Please read this manual in its entirety. This service information is intended to be used by a

qualified service technician, who is familiar with proper and safe procedures to be followed when

repairing, replacing, or adjusting any Dixie-Narco vender components. All repairs should be

performed by a qualified service technician who is equipped with the proper tools and replacement

components, using genuine Dixie-Narco factory parts.

REPAIRS AND/OR SERVICING ATTEMPTED BY UNQUALIFIED

PERSONS CAN RESULT IN HAZARDS DEVELOPING DUE TO

IMPROPER ASSEMBLY OR ADJUSTMENTS WHILE PERFORMING

SUCH REPAIRS. PERSONS NOT HAVING A PROPER BACKGROUND

MAY SUBJECT THEMSELVES TO THE RISK OF INJURY OR

ELECTRICAL SHOCK, WHICH CAN BE SERIOUS OR EVEN FATAL.

RECEIVING INSPECTION

Upon receipt, inspect the vender for any shipping damage. If there is any damage, have the driver

note the damage on the bill of lading and notify Dixie-Narco. Although I.C.C. regulations require

that the consignee originate shipping damage claims, Dixie-Narco will be happy to assist you if

you must file a shipping damage claim.

UNPACKING THE VENDER

Remove the stretch wrap and top cover from the vender.

NOTE: DO NOT STORE THE VENDER OUTSIDE WITH STRETCH WRAP ON.

THIS COULD CAUSE THE STRETCH WRAP TO BOND TO THE

VENDER’S SURFACE, WHICH COULD DAMAGE THE FINISH.

Remove the shipping boards from the bottom of the vender. The shipping boards are attached

by the leveling legs. To avoid unnecessary damage to the leveling legs or base, remove the

shipping boards by using a 1-1/2 inch “socket type” wrench to unscrew the leveling legs. Be sure

to replace the legs after removing the shipping boards.

To open the vender, locate the door lock keys that are located inside the coin return cup. After

unlocking the door, rotate the T-handle counterclockwise until the door can be opened. Once

inside, remove and discard the wood shipping block from the bottom right side of the cabinet.

Check the coin box, under the can/bottle chute, and between the column walls for any additional

flavor strips, additional parts, pricing labels or information concerning factory installed parts such

as coin mechanism, validator or card reader. Check the T-handle for proper alignment with the

cabinet and locking functions. Check the lamp for proper operation.

WARNING: ENSURE THAT POWER IS DISCONNECTED FROM THE

VENDER OR THAT THE POWER INTERRUPT SWITCH (IF PROVIDED)

IS NOT DEFEATED BEFORE INSPECTING OR REPLACING THE

LAMPS. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY

SUBJECT THE USER TO THE RISK OF ELECTRICAL SHOCK, WHICH

CAN BE SERIOUS OR FATAL.

WARNING: DO NOT STORE ANYTHING OR ALLOW DEBRIS OF ANY

KIND TO ACCUMULATE IN THE BOTTOM OF THE DOOR, IN AND

AROUND THE REFRIGERATION COMPARTMENT OF THE CABINET,

OR IN FRONT OF THE EVAPORATOR AND CONDENSER COILS.

ELECTRIC POWER REQUIREMENTS

Refer to the cabinet serial number plate/label to determine the proper voltage and frequency

required by the vender. The cabinet serial number plate/label also indicates the amperage or

wattage required by the vender. Single phase, alternating current is required. The vender must be

plugged into its own properly rated circuit with its own circuit protection (fuse/circuit breaker) in

accordance with the National Electrical Code and local codes and ordinances.

DO NOT USE AN EXTENSION CORD

GROUND THE VENDER

The vender is equipped with a three-wire power supply cord and must be plugged into a properly

grounded outlet. DO NOT REMOVE THE GROUND PIN OR IN ANY WAY BYPASS,

MODIFY, DEFEAT, OR DESTROY THE GROUNDING SYSTEM OF THE VENDER. If

the outlet will not accept the power cord plug, contact an electrician to install a proper AC outlet.

WARNING: FAILURE TO COMPLY WITH THESE INSTRUCTIONS

MAY SUBJECT THE USER TO THE RISK OF INJURY

OR ELECTRICAL SHOCK, WHICH CAN BE SERIOUS

OR FATAL.

PLACING THE VENDER ON LOCATION

CAUTION: DO NOT TRANSPORT THE VENDER TO OR FROM THE

LOCATION LOADED WITH PRODUCT OR DAMAGE

TO THE VENDER MAY RESULT.

The vender must be located on a solid, flat, and level surface. Ensure the surface can bear the

weight of a fully stocked vender. The vender must be positioned close enough to an electrical

outlet so that an extension cord is not required. If the machine will be subject to user misuse or

vandalism, is it recommended that that vender be secured to the floor or wall as described in Dixie-

Narco Technical Bulletin No. 344. Call the Dixie-Narco Technical Service Department or your

Dixie-Narco Representative for assistance.

LEVEL THE VENDER

Level the vender. When the vender is level, the door can be opened to any position and it will not

move by itself. Open the door to several different positions before deciding that the vender is

level. A carpenter’s level will help verify the machine is level. Make sure that all of the leveling

legs are in contact with the floor. If you cannot level the vender in its current location, select

another location. DO NOT PLACE ANY OBJECTS UNDER THE MACHINE!

DANGER: THE VENDER MUST BE PROPERLY LOCATED AND

LEVELED. IF THE MACHINE WILL BE SUBJECT TO

USER MISUSE OR VANDALISM IT IS RECOMMENDED THAT

THE VENDER BE SECURED TO THE FLOOR OR WALL

AS DESCRIBED IN DIXIE-NARCO TECHNICAL BULLETIN

NO. 344 TO MINIMIZE THE RISK OF INJURY OR DEATH

FROM TIPPING. CALL DIXIE-NARCO TECHNICAL SERVICE

DEPARTMENT, OR YOUR DIXIE-NARCO REPRESENTATIVE

FOR ASSISTANCE.

SPACE THE VENDER

Do not block the rear of the vender. Maintain a minimum of 4 in. (10 cm) from the wall to ensure

adequate airflow to the condenser and compressor. At the front of the vender, make sure that

nothing obstructs the air intake at the bottom of the main door. At the rear of the vender, make

sure nothing obstructs the air exhaust at the bottom of the cabinet.

INSTALLING FLAVOR CARDS

CIRCULAR OR FLAT FULL LENGTH SIGN

The flavor cards are inserted into the back of the selection buttons. Where applicable, swing the

coin changer mounting plate away from the outer door exposing the back of the select buttons.

The flavor cards are perforated on the right side. Bend the flavor card 90 degrees at the perforation

so that the right edge is toward the back of the flavor card. This will aid in easy installation and

removal of the flavor card. The flavor cards can now be inserted into the back of the selection

buttons from the left side. Ensure that the flavor cards are placed in the selection buttons that

correspond to the columns in which the product is loaded.

DISPLAY VENDERS

Remove bag of arrows, price labels and button caps from the cash box. Referring to the product

installation chart below (Fig. 1), place price sticker on arrow and place arrow in the clear plastic

cap noting that the bottom row of buttons point downward. Next, install clear cap with arrow onto

selection switch and push firmly until cap snaps into place.

INSTALLING PRODUCT IN DISPLAY

Open main door and open inner door to gain access to product

display box. Locate the two locking tabs at the top and bottom left

side of the display box. Lifting these two tabs will allow the product

display box to swing open. Again referring to figure 1, carefully

install the product into the clips provided being sure not to puncture

the display product.

Figure1

GE TEMPERATURE CONTROL ADJUSTMENT

Adjustment #1 – GE Temperature Adjustment

The GE Temperature control is factory preset at position #4 as shown in figure 2. Turn the

Temperature adjustment screw shown in figure 2 in a clockwise direction for colder product or in a

counter clockwise direction for warmer product.

Figure 2

Adjustment #2 – GE Temperature Control Altitude Adjustment

WARNING: DISCONNECT POWER TO THE VENDING MACHINE

BEFORE PROCEEDING WITH THIS ADJUSTMENT.

The control is factory set for an altitude of 500 feet (152 meters). For higher

altitudes, adjust the altitude correction screw shown in figure 2 in a clockwise

direction according to the chart below (figure 3).

Temperature

Adjustment Screw

Altitude

Adjustment Screw

This scale may be used as a Altitude Correction Table:

guide for measuring degrees Both Cut-In & Cut-Out

of rotation required for Must Be Adjusted

altitude correction. The Altitude, Counter

arrows indicate direction of Feet Clockwise Turns

screw rotation. 1/60 of a 2000 7/60

turn equals 6 degrees of 3000 13/60

rotation 4000 19/60

5000 25/60

6000 31/60

7000 37/60

Turn cut-in or cut-out screws 8000 43/60

clockwise to obtain colder Type "Q" Control 9000 49/60

operating temperatures. (Constant Cut-In) 10000 55/60

Figure 3

LOADING INSTRUCTIONS

PRODUCT SHIMMING

Dixie-Narco venders are shipped ready to vend 12 oz. (330ml) cans unless another package

was specified at the time the vender was ordered. To vend an alternative package, contact

Dixie-Narco Technical Service or refer to the appropriate Dixie-Narco set up information for

the package to be vended.

II. Vend Motor Cam Adjustments

Locate the lift tab on the outer edge of the adjustable cam. Lift the tab and rotate the

cam to the required setting.

III. Package Loading (Wide Column)

Position the oscillator as shown below. Load packages 1,2,3, and 4 as shown, in both

the front and the rear of the column. The front and the rear product must be loaded

evenly. Load all products with the top of the product facing the rear of the vender,

unless instructed otherwise.

IV. Rod and Spring Assembly installation (Narrow Column)

Insert the rod as shown below. Refer to the appropriate Technical Bulletin or

refer to the appropriate Dixie-Narco set up information for the package to be

vended for the proper position of the rod.

V. Package Loading (Narrow Column)

Position the rotors as shown. Load the packages numbered 1, 2, and 3 as shown in

both the front and rear of the column. The front and the rear product must be

loaded evenly. Load all products with the top facing the rear of the vender, unless

instructed otherwise.

CLEANING THE VENDER

DO NOT USE A WATER JET OR NOZZLE TO CLEAN THE VENDER

SIGN FACE

The polycarbonate sign face requires proper cleaning to prolong its service life. It is

recommended that you periodically inspect and clean the sign face as follows:

• Unplug the vender

• Inspect the sign face for any damage.

• Rinse the sign with a soft cloth or sponge soaked in warm water

• If necessary, use a mild soap or loosen any dirt or grime. To prevent damage, DO

NOT SCRUB or use a brush or squeegee, as some signs have a clear ultraviolet

resistant coating to prevent yellowing.

• Repeat the above steps as necessary

• To prevent spotting, dry the sign with a soft cloth

CABINET

• Unplug the vender.

• Wash the cabinet with a good detergent or soap mixed in warm water.

• Wax the vender often with a good grade of automotive wax.

• Any corrosion inside the vender should be removed with fine steel wool and the

area should be painted with aluminum paint.

• Repair any scratches on painted surfaces to prevent corrosion.

The compressor electrical circuit is always live when the plug is

connected to an electrical outlet.

REFRIGERATION CONDENSER

• Check the condenser periodically for dirt or lint build up.

• Remove the build up with a brush or vacuum, or blow the dirt out of the

condenser with compressed air and approved safety nozzle.

• Ensure nothing obstructs air intake at the bottom of the main door.

• Ensure nothing obstructs air exhaust at the rear of the cabinet.

DRAIN PAN/SOAKERS

• Check the drain pan & soakers periodically for dirt, debris, and proper alignment.

• Remove any dirt and debris by removing the drain pan, cleaning pan and soakers,

and reinstalling.

• Ensure nothing is obstructing the drain tube and drain hose.

COIN ACCEPTOR

• Follow the Coin Acceptor Manufacture’s Instruction.

Recommended Maintenance Schedule

Time Component Lubricant Example

Every Six Months Main Door

(or as needed) 1. Lock Bolt and Nut Retainer Mechanics Friend

2. Hinge Pivot Points Mechanics Friend

Inner Door

1. Hinge Pivot Points Mechanics Friend

Every Year Inner Door

(or as needed) 1. Door Gasket Petroleum Jelly

Dixie-Narco, INC.

Dixie-Narco Blvd.

Williston, SC 29853

Phone 803-266-5001

Fax 803-266-5049

Altri manuali per 90 Series

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Dixie Narco Distributore automatico

Dixie Narco

Dixie Narco 2145 Istruzioni per l'installazione e il funzionamento

Dixie Narco

Dixie Narco Pre SRS 90 SP Manuale utente

Dixie Narco

Dixie Narco P Series Manuale utente

Dixie Narco

Dixie Narco 90 Series Manuale utente

Dixie Narco

Dixie Narco P Series Manuale utente

Dixie Narco

Dixie Narco DPSL5 E Manuale utente

Dixie Narco

Dixie Narco 55 Series Manuale utente

Dixie Narco

Dixie Narco SIID Manuale operativo

Dixie Narco

Dixie Narco FLEXPAK 3000 Series Manuale utente

Dixie Narco

Dixie Narco HVV 276E Manuale utente

Dixie Narco

Dixie Narco P Series Manuale utente

Dixie Narco

Dixie Narco 90 Series Manuale utente

Dixie Narco

Dixie Narco M036.2 Manuale utente

Dixie Narco

Dixie Narco DN 55 Series Manuale utente

Dixie Narco

Dixie Narco DNCB 168 Guida rapida

Manuali Distributore automatico popolari di altre marche

Godrej

Godrej Minifresh 2000 Manuale utente

LAUREL

LAUREL 300 Istruzioni per l'installazione e il funzionamento

Macas

Macas MACES7C-300-90-00 Series Manuale utente

VendNet

VendNet CB500-SA Manuale utente

FAS International

FAS International FASTER TMT Manuale utente

Three Square Market

Three Square Market Kiosk Manuale utente

Seaga

Seaga JDL-2 COMBO Istruzioni per la costruzione

Fastcorp

Fastcorp F820 Istruzioni per la costruzione

Coinco

Coinco BillPro Manuale operativo

Intralot

Intralot OHIO MPNG Manuale utente

LAVAZZA

LAVAZZA KLIX Series Manuale utente

Azkoyen

Azkoyen Zensia Manuale

Azkoyen

Azkoyen STEP 74 Manuale

SandenVendo

SandenVendo Snack Safety Point SVE SSP Manuale del proprietario

Intralot

Intralot Dreamtouch Smart Manuale utente

Westomatic

Westomatic Primo Compact Manuale utente

Crane

Crane Dixie-Narco Glassfront BevMax 3 5800 Manuale utente

Jofemar

Jofemar Vision Snack Plus Manuale utente