dji RSC 2 Manuale utente
DJI RSC 2 快速入门指南
认识 DJI RSC 2
1. Tilt Motor
2. Tilt Lock
3. Screen
4. Side Wheel
5. Camera Control Button
6. Joystick
7. M Button
8. Extended Grip/Tripod
9. Back Button
10. M4/NATO 接口
11. Lock Knob
12. Lower Quick-Release Plate
13. Upper Quick-Release Plate
14. Image Transmission/Focus Motor Port (USB-C)
15. Focus Motor Port (USB-C)
16. RSS Camera Control Port (USB-C)
17. Front Dial
18. Trigger
19. Power Button
20. Power Port (USB-C)
21. Pan Lock
22. Pan Motor
23. Roll Lock
24. Roll Motor
Getting Started
A. Downloading the DJI RONINTM App and Watching the Tutorials
B. Charging the Battery and Checking the Battery Level
Before using for the first time, charge the DJI RSC 2 through the power port using a charging
cable (included) and a USB adapter (not included). It is recommended to use a USB adapter
with QC 2.0 and PD protocol (max. 24 W). Check the battery level through the screen.
C. Attaching the Extended Grip/Tripod
D. Unfold and unlock the gimbal
E．Powering On/Off and Entering/Exiting Sleep Mode
Press and hold the power button to turn DJI RSC 2 on or off. Tap or press twice to enter or exit
sleep mode.
F．Activating DJI RSC 2
DJI RSC 2 needs to be activated through the Ronin app before using for the first time.
1. Press and hold the power button to power on the gimbal.
2. Enable Bluetooth on your mobile device and launch the Ronin app. Note that a DJI account is
required to launch the Ronin app. Once detected in the list of Bluetooth devices, select DJI RSC 2
and input the default Bluetooth password: 12345678. Make sure you are connected to the internet
and follow the on-screen instructions to activate DJI RSC 2.
Mounting the Camera
Make sure to prepare the camera before mounting it to DJI RSC 2. Remove the lens cap and check
that the battery and memory card are inserted in the camera. Make sure DJI RSC 2 is powered off
or in sleep mode before mounting the camera.
1. Attach the Upper Quick-Release Plate
The camera lens and the arrow on the bottom of the upper quick-release plate must face the same
direction. Attach the upper quick-release plate to the camera by tightening the screw.
2. Attach the Lower Quick-Release Plate and Lens-Fastening Strap
3. Attach the Camera to the Gimbal
To remove the lower quick-release plate, toggle the lever on the camera mounting plate to the
unlocked position and remove the lower quick-release plate while pressing the safety lock on the
mounting plate.
4. Connect the Camera Control Cable.
Choose the proper camera control cable according to the camera type. Plug one end of the cable
into the RSS camera control port of the gimbal and plug the other end into the camera.
Balancing
Balancing is required before shooting. Before balancing, make sure to power on the camera if using
an optical zoom lens and to select the focal length if using a varifocal lens. Make sure DJI RSC 2 is
powered off or in sleep mode before balancing.
1. Balancing the Vertical Tilt
a. Unlock the tilt axis and loosen the mounting plate knob.
b. Rotate the tilt axis so that the camera lens is pointing upward. Check to make sure the camera
is not top or bottom-heavy. If top-heavy, move the camera backward. If bottom-heavy, move the
camera forward.
c. Tighten the mounting plate knob while holding the camera upward. The vertical tilt is balanced
when the camera is steady while pointing upward.
2. Balancing Depth for the Tilt Axis
a. Rotate the tilt axis so that the camera lens is pointing forward. Toggle the lever to the unlocked
position.
b. Check to make sure the camera is not front or back-heavy. If front-heavy, move the camera
backward by turning the knob. If back-heavy, move the camera forward.
c. Toggle the lever to the locked position. The tilt axis is balanced when the camera is steady while
tilted up or down by 45°.
d. Lock the tilt axis.
3. Balancing the Roll Axis
a. Unlock the roll axis. Loosen the knob on the roll arm.
b. Check the direction in which the roll motor swings. If the camera rotates to the left, move the
camera to the right. If the camera rotates to the right, move the camera to the left.
c. Tighten the knob. The roll axis is balanced when the camera is steady.
d. Lock the roll axis.
4. Balancing the Pan Axis
a. Unlock the pan axis. Loosen the knob.
b. While holding the grip, tilt DJI RSC 2 forward, and rotate the pan arm until parallel with you.
c. Check the movement of the pan axis. If the camera lens rotates to the left, push the pan axis to
the right. If the camera lens rotates to the right, push the pan axis to the left.
d. Tighten the knob. The pan axis is balanced when the camera is steady when rotating the pan
while tilting the grip.
Operation
After balancing, make sure the three axes are unlocked before powering on DJI RSC 2.
Screen Operation
Turn the side wheel to scroll the menu and press to confirm option. Press the back button to go
back to the previous menu.
Button Functions
Power Button
Press and hold to power on or off.
Tap or press twice to enter or exit sleep mode.
Trigger
Tap once to start ActiveTrack (requires the Image Transmission System to be enabled).
Press and hold to enter Lock mode.
Tap twice to re-center the gimbal.
Tap three times to turn the gimbal 180°so that the camera faces you (selfie mode).
Camera Control Button*
Press halfway for autofocus.
Press once to start or stop recording.
Press and hold to take a photo.
M Button
Tap to select a user profile.
Press and hold to enter Sport mode.
Press and hold and press the trigger twice to remain in Sport mode. Repeat to exit Sport mode.
Quickly tap twice to enter portrait mode.
Press three times to enter or exit 3D Roll 360. When in 3D Roll 360, move the joystick left or right
twice to automatically rotate the camera. Tap the trigger twice to stop continuous auto rotation.
Press and hold the M button together with the trigger to begin auto tune.
Front Dial*
Turn to control focus (default setting).
Joystick
Push up or down to control the movement of the tilt axis (default setting). Push left or right to
control the movement of the pan axis (default setting).
*The functions of the camera control button and front dial vary according to the camera and
require the camera control cable to be connected. Refer to the DJI RSC 2 Camera Compatibility List
on www.dji.com/rsc-2 for more information.
Ronin App
Use the Ronin app to access more functions such as Force Mobile, virtual joystick, and gimbal and
camera settings.
Specification
Weight
Gimbal: Approx. 1196 g（excl. quick-release
plate and NATO adapter）
Extended Grip/Tripod（metal）：Approx.226 g
Extended Grip/Tripod（plastic）：Approx.226 g
Quick-Release Plate：Approx.102 g
Model
P10
Dimensions
Gimbal (folded): 260 × 210 × 75 mm
Gimbal (unfolded)：400 ×185 ×175 mm (incl.
grip, excl. Extended Grip/Tripod
Input Power
Model：RB2-3400mAh-7.2V
Type：18650 2S
Capacity：3400 mAh
Energy：24.48 Wh
USB Input
5V/2A, 9V/2A, 12V/2A, 15V/1.6A
Bluetooth Operating Frequency
2.40 GHz -2.4835 GHz
Operating Temperature
-20°to 45°C (-4°to 113°F)
Max Standby Time
14
hours
Charging Time
2
hours（when using a 18
W charger）
FCC Compliance Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept
any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. End user must follow the specific operating instructions for satisfying RF exposure
compliance. This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
ISED Compliance Notice
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the
following two conditions: (1)This device may not cause interference.(2)This device must accept any
interference, including interference that may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR
d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :(1)L’appareil ne doit
pas produire de brouillage; (2)L’appareil doit accepter tout brouillage radioélectrique subi, même
si le brouillage est susceptible d’en compromettre le fonctionnement.
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled
environment. End user must follow the specific operating instructions for satisfying RF exposure
compliance. This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.The portable device is designed to meet the requirements for exposure to
radio waves established by the ISED.
部件名称
有害物质
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr+6)
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
线路板
×
○
○
○
○
○
外壳
×
○
○
○
○
○
金属部件
（铜合金）
×
○
○
○
○
○
内部线材
×
○
○
○
○
○
其他配件
×
○
○
○
○
○
本表格依据SJ/T 11364 的规定编制。
○：表示该有害物质在该部件所有均质材料中的含量均在GB/T 26572 规定的限量要求以下。
×：表示该有害物质至少在该部件的某一均质材料中的含量超出GB/T 26572 规定的限量要
求。（产品符合欧盟ROHS指令环保要求）
KCC Compliance Notice
“
.”
“ ”
NCC Compliance Notice
取得審驗證明之低功率射頻器材，非經核准，公司、商號或使
用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。低功率射
頻器材之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應
立即停用，並改善至無干擾時方得繼續使用。前述合法通信，指依電信管理
法規定作業之無線電通信。低功率射頻器材須忍受合法通信或工業、科學及
醫療用電波輻射性電機設備之干擾。
設備名稱：DJI RSC 2，型號（型式）：P10
單元
Ｕnit
限用物質及其化學符號
鉛Lead
(Pb)
汞
Mercury
(Hg)
鎘
Cadmium
(Cd)
六價鉻
Hexavale
nt
chromium
(Cr+6)
多溴聯苯
Polybromin
ated
biphenyls
(PBB)
多溴二苯醚
Polybromina
ted
diphenyl
ethers
(PBDE)
線路板
－
○
○
○
○
○
外殼
○
○
○
○
○
○
排針
○
○
○
○
○
○
其他
－
○
○
○
○
○
備考 1.〝超出 0.1 wt %〞及〝超出 0.01 wt %〞係指限用物質之百分比含量超出百
分比含量基準值。
備考 2.〝○〞係指該項限用物質之百分比含量未超出百分比含量基準值。
備考 3.〝－〞係指該項限用物質為排除項目。
EU Compliance Statement: SZ DJI Osmo Technology Co., Ltd. hereby declares that this device is in
Altri manuali per RSC 2
2
Indice
Altri manuali dji Accessori per fotocamere
dji
dji OSMO MOBILE SE Manuale utente
dji
dji MATRICE 30 Series Manuale di istruzioni
dji
dji OSMO MOBILE 2 Manuale utente
dji
dji RS 2 Manuale utente
dji
dji RONIN-SC Manuale utente
dji
dji RSC 2 Manuale utente
dji
dji OSMO+ Manuale utente
dji
dji RONIN-S Focus Motor Manuale utente
dji
dji MINI 3 PRO Manuale utente
dji
dji RONIN-SC Manuale utente
dji
dji OSMO MOBILE 3 Manuale utente
dji
dji RONIN-SC Manuale utente
dji
dji BS30 Manuale utente
dji
dji OSMO Manuale utente
dji
dji Remote Start/Stop Manuale utente
dji
dji RONIN-SC Manuale utente
dji
dji Zenmuse Z15 Manuale utente
dji
dji OSMO MOBILE 6 Manuale utente
dji
dji RONIN 2 Manuale utente
dji
dji Ronin-MX Manuale utente
