DK System DK LOGIC 200 Manuale utente

WIRELESS

ROOM

THERMOSTAT

DK LOGIC 200

Manual

INS-012-005 130X184,5

Wireless room thermostat DK LOGIC 200

Table of Contents

1. Description of a thermostat...................................................................

2. Notes on installation...............................................................................

3. Description of the transmitter components - display..........................

4. Description of the transmitter components - buttons.........................

5. Thermostat installation - transmitter.....................................................

6. Description of the receiver components..............................................

7. Installation and connection of the receiver to electrical system.......

8. Receiver encoding..................................................................................

9. Interferences - communication error....................................................

10. Description of LEDs singalling system..............................................

11. Options of the thermostat - transmitter..............................................

12. First start...............................................................................................

13. PROG mode - programming for automatic operation......................

13.1 Program Pr. 1 and Pr. 2.....................................................................

13.2 Program Pr.3 - user settings..............................................................

13.3 Example - programming the automatic operation mode....................

14. Momentary temp. change in automatic mode....................................

15. MANU mode - manual operation mode...............................................

16. TEST function........................................................................................

17. Protection against freezing function...................................................

18. CLO mode - setting the current hour and day....................................

19. PAr1 mode - a parameter visible on a main screen...........................

20. PAr2 mode - program version and RESET..........................................

21. Setting a default day and night temperature......................................

22. OFF function.........................................................................................

23. Battery replacement.............................................................................

24. Faults.....................................................................................................

25. Technical data - transmitter.................................................................

26. Technical data - receiver......................................................................

27. Table of programs.................................................................................

28. Rules of conduct with waste electrical and electronic equipment..

Wireless room thermostat DK LOGIC 200

1. Description of a thermostat

2. Notes on installation

A wireless room thermostat DK LOGIC 200 is designed for automatic adjustment

of temperature in a room by switching on/off of the boiler.

The thermostat is equipped with a relay output, which sends an on / off signal

when the pre-set temperature has been exceeded.

A device has the following features:

q ability of selecting different programs for each day of the week

q two factory pre-set programs

q two selectable temperature - day and night

q six heating periods per day

q easy and intuitive programming

q possibility of short-term changes in heating temperature

q easy installation

q frost protection

q heater adjustable every 0.5 °C

q multifunction display

q memorizing all the settings, even in the long-term absence of batteries

q The device must be installed by an authorized person.

qIt is required that the boiler had its own safeguards against excessive

temperature rise of the boiler caused e.g. boiler controller or related

equipment malfunction.

qThe controller should be placed in a location that prevents its heating to a

temperature higher than 40 °C.

qThe controller must not be exposed to water and conditions causing

condensation (e.g. sudden changes in ambient temperature).

qThe device should be installed and operated as described in the assembly

description and rules for electrical equipment.

Wireless room thermostat DK LOGIC 200

2. Notes on installation (cont.)

q Before starting the transmitter and receiver, you should check the electrical

connections.

q Connection of the power cord should be made with the device powered off (a

power plug must be disconnected from the mains). Connection of the devices

with the mains plug of the controller plugged in creates an electric shock.

q You must not use a damaged devices.

3. Description of the transmitter components - display

Fig. 1 Display components

1. Flashing point indicating the current time

2. Indication of the option currently in use: AUTO, MANU, PROG

3. Indication of protection against freezing

4. Display of temperature or time

5. Indication of boiler operation

6. Indication of the lowered temperature (night mode)

7. Indication of the comfort temperature (day mode)

8. Graphic presentation of the selected program

AUTO

MANU

PROG P

Note: The “room thermostat service” option must be turned on in

the programmer after the thermostat has been connected to the

boiler's programmer.

Wireless room thermostat DK LOGIC 200

4. Description of the transmitter components - buttons

5. Thermostat installation - transmitter

Thermostat DK LOGIC 200 should be located in a place not exposed to other

sources of heat (radiator, fireplace, etc.), affecting the accuracy of the

temperature readout in the room. The device consists of two parts: front - a

microprocessor and rear - connector.

1. Menu

2. Setting the temperature (comfort / lowered), operation in a manual mode,

operation in an anti-freezing mode

3. Confirmation; additionally in AUTO mode, when the button is pressed the

pre-set temperature, time and a day of the week are displayed

4. Change of functions or pre-set values.

1 2 3

1. Detach the front and back parts of the thermostat.

2. Install the back part directly on a wall.

3.Put two 2 x 1.5 V alkaline batteries type AA / LR6 into the front part of the

thermostat.

4.Put the front and back part together - a thermostat is ready for

programming.

Fig. 2 Description of the transmitter's buttons

Wireless room thermostat DK LOGIC 200

6. Description of the receiver components

Fig. 3 Description of the receiver components

N LRE1

5 5

6 7 8

POWER SUPPLY

INTERFERENCES

RE1

1. Green diode - POWER SUPPLY

2. Blue diode - COMMUNICATION

3. Red diode - INTERFERENCES

4. Orange diode - RE1 boiler relay

5. Installation slots

6. FUNCTIONS button

7. RE1 - clamps to install the boiler wires

8. NL - power supply clamps ~230 V, 50 Hz

Wireless room thermostat DK LOGIC 200

7. Installation and connection of the receiver to electrical

system

1. Open the front part of the receiver housing.

2. Using two screws and dowels attach the receiver to the wall.

3. Turn off the voltage on a wire feeding the receiver.

4. Connect the cables between a boiler or a programmer and a RE1 clamp in the

receiver (Fig.4).

5. Connect the feeder cable with the appropriate clamps in the receiver (Fig.4):

-a blue wire must be connected to the N clamp (“neutral”)

-a brown wire must be connected to the L clamp (“phase”)

6. Close the front part of the receiver housing.

7. Turn the power on - a green diode POWER SUPPLY should lit on the receiver,

informing on the correct connection.

Note: As the radio interferences are possible, it is recommended to

install the receiver at least 0.5m from large metal objects and

electrical quads

Fig. 4 Diagram of the receiver connections to the boiler/programmer and to

the electrical system

N LRE1

RE1

~ 230 V, 50Hz

Boiler or

programmer

POWER SUPPLY

INTERFERENCES

Wireless room thermostat DK LOGIC 200

8. Receiver encoding

9. Interferences - communication error

A transmitter and receiver, which can be found in a single original box, have been

pre-set in the factory to use thus their encoding is not necessary.

If needed, the encoding steps described below must be followed:

Radio wave interferences may occur sporadically,

which can lead to a lack of communication

between the receiver and the transmitter. If this

happens, a red INTERFERENCES diode starts to

blink on a receiver and an Err1 message will be

displayed on the transmitter screen.

To restore communication follow the steps

described in the encoding process - see point 8

Receiver encoding.

1. Press and hold for 5 sec. the FUNCTIONS button - the memory will reset -

a blue and red diodes will lit at the same time. Once the memory is cleared, a

red diode INTERFERENCES will flash.

2. Press and hold for 1.5 sec. the FUNCTIONS button - the receiver will go to

a standby mode waiting for a code to be introduced - a blue and red diodes

will be flashing alternately.

3. At that time, a TEST function must be called on the DK LOGIC 200

transmitter. A code will be directed to a receiver: two diodes blue and red will

blink twice at the same time.

4. Next, a short communication test will be made - the RE1 relay will be

connected twice and an orange diode will be lit.

5. The transmitter and receiver set has been properly configured.

Wireless room thermostat DK LOGIC 200

11. Options of the thermostat - transmitter

10. Description of LEDs singalling system

AUTO Automatic mode - a thermostat works by the

pre-set program in line with the adjusted

day and night mode temperature.

MANU Manual mode - allows adjustment of the

heating temperature without interfering in

the pre-set program.

CLO Hour and day setting mode.

MANU

AUTO

PROG Time range programming mode for a day

and night temperature.

PROG

PAr1 A setting mode of the permanently visible

parameter (hour and temperature).

GREEN diode is on receiver well connected to the grid

BLUE diode blinks sending or receiving the signal

RED diode blinks no encoding - memory is empty

RED diode is on interferences

ORANGE diode is on RE1 relay is shorted

BLUE and RED diodes blink alternately waiting for the code

BLUE and RED diodes blink at the same time receiving the code

BLUE and RED diodes are on at the same time erasing the memory

PAr2 Program # and RESET.

OFF Turning off thermostat operation.

Wireless room thermostat DK LOGIC 200

12. First start

13. PROG mode - programming for automatic operation

1. When the batteries are in, the display will show

0:00 hours, and the thermostat will work in P1

mode - see point 13 “PROG mode - program-

ming the automatic operation mode”.

1. Press twice until the PROG appears on

the screen. Confirm by pressing .

AUTO

2. Use the “-/+” buttons to set the actual hour.

Confirm by pressing ; To set minutes,

please follow the same procedure. Confirm by

pressing . A screen showing the current

day of the week will be shown.

3. Use the “-/+” buttons to set the actual day of the

week. Confirm by pressing . The controller

will show the main screen, taking into account

the introduced settings. The controller is in the

P1 program - see point 13 “PROG mode -

programming the automatic operation

mode”, using the default settings of the

comfort temperature (day) at the level of 21°C

and the lowered temperature (night) at the level

of 18°C. The way of changing the default

tempe-ratures has been described in the point

21 “Setting the default day and night tempe-

rature”.

AUTO

2. Use “-/+” to select one of the programmes (Pr.

1, Pr. 2 or Pr. 3) and confirm by pressing

For Pr. 1 and Pr. 2, the controller will go to to the

main screen view; For Pr. 3 the proces of

individual settings programming must be

continued.

PROG

Indice

Altri manuali DK System Termostato

DK System

DK System DK LOGIC 100 Manuale utente

Manuali Termostato popolari di altre marche

EWELLY

EWELLY EW-181 Manuale utente

Prolon

Prolon T1100 Istruzioni per l'installazione

Computherm

Computherm Q20 Manuale utente

Heatmiser

Heatmiser neoStat Manuale utente

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuale utente

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuale utente

Saswell

Saswell SAS920XWHB-7-S-RF Guida

Aircalo

Aircalo TFP1-ET85P2 Manuale utente

Honeywell

Honeywell CM721 Manuale utente

Carrier

Carrier DEBONAIR 33CS Manuale utente

Lennox

Lennox iHarmony Zone Thermostat Istruzioni per il montaggio

Gemtech

Gemtech GT7000 Manuale di istruzioni

Rollei

Rollei Smartes 45000 Manuale utente

Sinope

Sinope TH1300RF Manuale utente

Honeywell

Honeywell RLV4305 Manuale utente

Honeywell

Honeywell Prestige 2.0 THX9421 Manuale utente

NuTone

NuTone NTBZ48 Istruzioni operative originali

Stelpro

Stelpro MAESTRO ASMT402AD Manuale utente