DK2 Power OPC506 Manuale utente
OPC506
6 INCH COMMERCIAL CHIPPER
SWING CHUTES • TOWABLE • KOHLER® ENGINE
ASSEMBLY GUIDE
DK2 CORPORATE HEAD OFFICE
5330 MAINWAY
BURLINGTON, ONTARIO
L7L6A4 CANADA
DK2 USA WEST
4301 S VALLEY VIEW BLVD. SUITE 10-11
LAS VEGAS, NEVADA
89103 USA
DK2 USA EAST
3750 SOUTH AVENUE, NORTH UNIT
TOLEDO, OHIO
43615 USA
PARTS AND SERVICE 702-331-5353
-
WWW.DK2POWER.COM
2
STEP 1
CHECK THE PACKING
1. Open and unpack all items. Leave lots of working space.
2. Inspect all parts.
NOTE: UPON INSPECTION OF PARTS, IF YOU FIND ANY MISSING PARTS PLEASE CALL
DK2 POWER AT 702-331-5353 OR CONTACT US VIA OUR WEBSITE
WWW.DK2POWER.COM
PLEASE DO NOT RETURN TO THE STORE.
3
STEP 2
INSTALL CHUTES
1. Install the feed chutes on the 2 hinges. To seat the hinge pins for the first time a
rubber mallet may be used to tap the pins into the hinges. These are tight fitting to
reduce vibration noise.
2. Close each Chute, and latch them.
3. Assemble the chip shield to the chip chute.
4. Plug the safety key shut o wire connectors together on the large chute.
4
STEP 3
INSTALL AXLE AND TIRES
1. Remove all hardware from axle.
2. Install with 4 bolts to machine body.
3. Install wheels with air stem facing out, then large washer, then nut, then turn by
hand to tighten, back o nut to align hold and insert pin and secure.
4. Align wheel cap in groove and tap easy with a rubber mallet or a block of wood and
a hammer until seated all around even into the groove.
5
STEP 4
INSTALL TOW BAR ASSY
1. Tip the unit back and rest the large chute on the ground.
2. Install with 4 bolts the front tow assembly.
6
STEP 5
INSTALL DROP STAND
1. Install the drop stand and pin it.
7
STEP 6
INSTALL TOW BAR
1. Slide and lock the tow bar and you’re all done.
8
ENGINE
ENGINE CHECKLIST
READ THE KOHLER® ENGINE MANUAL SUPPLIED WITH YOUR UNIT FOR FULL ENGINE
OPERATION, SAFETY, AND MAINTENANCE PROCEDURES.
1ON/OFF KEY LOCK
2GAS - USE MID-GRADE OR HIGHER
3CHOKE - LEFT IS ON / RIGHT IS OFF (RUN POSITION)
4GAS ON/OFF SWITCH - LEFT IS OFF / RIGHT IS ON
5THROTTLE - RABBIT FAST / TURTLE SLOW
6PULL STARTER - PULL TIGHT, THEN PULL START
7OIL - FILL TO MARK 10W30, WILL NOT START IF OIL IS LOW, HAS LOW OIL
SHUTOFF PROTECTION. 2 YELLOW CAPS ARE OIL FILL CAPS. USE EITHER ONE TO
FILL OIL.
9
BLADES
HOW TO REVERSE YOUR BLADES
YOUR CHIPPER IS EQUIPPED WITH DUAL REVERSABLE CUTTING BLADES.
1. Turn engine key o, remove key and unplug the spark plug.
2. Open the large feed chute.
3. Before removing the bolts that mount the blades, place paper towels in the area
opening between the drum and the drum housing. This will prevent bolts from
dropping into the drum housing.
4. Remove the first 4 bolts.
5. BEFORE REMOVING THE LAST BOLT BE SURE TO SUPPORT THE BLADE FROM
SLIDING DOWN INTO THE DRUM. More paper towels or a shop towel does a good
job.
6. Remove the blade, reverse it to the new sharp edge and reinstall it. Use only DK2
POWER OEM blades.
7. Use Loctite on the bolt threads when replacing bolts.
8. Use the supplied T-Handle tool to remove and replace bolts.
9. Wear protective gloves, the blades are very sharp.
10. Remove the paper towels, any paper left in the chipper will be cut up on the next
running operation.
EXAMPLE ON NEXT PAGE →
10
BLADES
HOW TO REVERSE YOUR BLADES
Altri manuali per OPC506
1
Indice
Lingue:
Altri manuali DK2 Power Cippatrice
DK2 Power
DK2 Power OPT118 Manuale utente
DK2 Power
DK2 Power OPC525 Manuale utente
DK2 Power
DK2 Power OPC566E Manuale utente
DK2 Power
DK2 Power OPC505AE Manuale utente
DK2 Power
DK2 Power OPC505AE Guida
DK2 Power
DK2 Power OPC524 Manuale utente
DK2 Power
DK2 Power OPC503 Manuale utente
DK2 Power
DK2 Power OPC566E Manuale utente
DK2 Power
DK2 Power OPC506 Manuale utente
DK2 Power
DK2 Power OPC524 Manuale utente
