DKS 2364-080 Manuale utente
WIRELESS REPEATER KIT
DoorKing Part Number
2364-080
The wireless repeater kit extends the wireless communication range between an access control system and wireless tracker expansion board or
just between wireless tracker expansion boards. It gets installed between the wireless systems that are too far or obstructed from each other to
reliably communicate with each other. It will repeat a signal sent to it and relay that signal to the next wireless system. Multiple repeaters can be
used in the same communication line of tracker expansion boards. The approximate signal range is 500 ft direct-line-of-sight with no signal
interference.
Power Transformer
See back page.
IMPORTANT:
Install the
repeater so the
antenna is in a
location that is
NOT surrounded
by metal and is
in free air as
high as possible
above the
ground.
Minumum 15 ft
above ground
recommended.
3.5”
5”
7.75”
3”
Antenna is REQUIRED.
(Included)
1/2” thick wall PVC conduit recommended
(not supplied).
Metal conduit may interfere with wireless signal.
Installation
0
F
E
D
C
B
A
9
8
7
6
5
4
3
2
1
0
F
E
D
C
B
A
9
8
7
6
5
4
3
2
1
RF ID RF CHANNEL
16
2364-010
POWER
RF LOST RF SYNC RF STRENGTH
POWER
ER
1/2”
Conduit
+
-
5 VDC
Range testing is HIGHLY recommended
before FINAL installation.
Important Antenna Note: Antenna range WILL VARY
GREATLY depending on individual setup (Antenna height
above the ground, background signal interference,
physical obstructions (trees, buildings etc.)).
Adverse weather (rain) CAN also affect antenna range.
120 S. Glasgow Avenue
Inglewood, California 90301 U.S.A.
Antenna is
REQUIRED.
DoorKing Part Number
2364-080
Power Transformer
18 GA. Wire 100 ft max
16 GA. Wire 200 ft max
0
F
E
D
C
B
A
9
8
7
6
5
4
3
2
1
0
F
E
D
C
B
A
9
8
7
6
5
4
3
2
1
RF RANGE
POS (+)
NEG (-)
READOUT
OFF/ON PROGRAM
SW1
RF ID RF CHANNEL
16
2364-010
POWER
Power transformer is REQUIRED
and is wired to the 2-pin terminal,
wire polarity matters.
5 VDC
RF LOST RF SYNC RF STRENGTH
RF SY
RF LO
LED Display
DISPLAY
OFF/ON
DISPLAY
OFF/ON
RF ChannelRF ID
0
F
E
D
C
B
A
9
8
7
6
5
4
3
2
1
0
F
E
D
C
B
A
9
8
7
6
5
4
3
2
1
Program Button:
Press after adjustment has been made to the RF RANGE,
RF ID or RF CHANNEL before changes will take effect.
Press and hold for 3 sec. to connect to wireless
baseboard, may take up to 20 seconds to connect.
(RF SYNC LED will blink when connected).
Press and hold again for 3 sec. to disconnect to a
connected wireless baseboard if necessary
(RF LOST LED will turn ON when disconnected).
RF SYNC:
Blinking - Communicating with a wireless board.
OFF - No signal with a wireless board.
RF LOST:
ON - NO communication with a wireless board.
Important
MUST be set to SAME
ID number and channel
number as the wireless
baseboard and tracker
expansion board(s).
Jumper set on RIGHT
side turns display ON.
(factory set) MUST
be ON to show RF
range and strength.
Jumper set on LEFT
side turns display OFF.
(50% board power
savings when OFF)
2-Pin Terminal
RF Range
Adjustment
Set to max (full clockwise) for most applications.
This may need to be dialed back to limit the range
when using multiple repeaters.
2364-065-E-11-14 Copyright 2014 DoorKing, Inc. All rights reserved.
Due to the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e.,
have errors) or be totally lost. Although significant delays or losses of data are rare when wireless devices are used in a normal manner with a
well-constructed network, DoorKing wireless products should not be used in situations where failure to transmit or receive data could result in
damage of any kind to the user or any other party, including but not limited to personal injury, death, or loss of property. DoorKing, Inc. accepts no
responsibility for damages of any kind resulting from delays or errors in data transmitted or received using DoorKing wireless products, or for
failure of DoorKing wireless products to transmit or receive such data.
Important Notice
Repeater Board Reference
Do not operate DoorKing wireless products in areas where cellular modems are not advised without proper device certifications. These areas
include environments where cellular radio can interfere such as explosive atmospheres, medical equipment, or any other equipment which may
be susceptible to any form of radio interference. DoorKing wireless products can transmit signals that could interfere with this equipment. Do not
operate DoorKing wireless products in any aircraft, whether the aircraft is on the ground or in flight. In aircraft, DoorKing wireless products
MUST BE POWERED OFF. When operating, DoorKing wireless products can transmit signals that could interfere with various onboard systems.
Note: Some airlines may permit the use of cellular phones while the aircraft is on the ground and the door is open. DoorKing wireless products
may be used at this time.
The driver or operator of any vehicle should not operate DoorKing wireless products while in control of a
moving vehicle. Doing so will detract from the driver or operator’s control and operation of that vehicle. In
some states and provinces, operating such communications devices while in control of a vehicle is an offence.
Safety and Hazards
RF Strength LED:
Updated every time a RF SYNC signal is received.
Green - Strong signal - Normal
Yellow - Marginal signal - May lose communication.
Red - Poor signal - Unreliable
•
•
•
See “Wireless System Layout and Start-Up Procedure” for system
layout limitations, checking and adjusting RF range of the repeater.
Altri manuali DKS Ripetitore
