DMX4ALL DMX-LED-Dimmer CC1 Manuale utente

DMX-LED-Dimmer CC1

User Manual

DMX-LED-Dimmer CC1 2

For your own safety, please read this user manual and warnings

carefully before installation.

Description

The DMX-LED-Dimmer CC1 is designed for controlling LEDs, which are operated

with constant current and works with up to 48V DC.

Output with selectable constant current modules

Different constant current modules with different output currents are available for

connection. The constant current modules are available as accessories and are not

included in the scope of delivery.

Power supply from 12V up to 48V

The DMX-LED Dimmer CC1 works with supply voltages from 12V to 48V.

0% to 100%

The connected LEDs can be dimmed via PWM of 0% up to 100%.

DMX FAIL-Function

An adjustable DMX FAIL-Function offers the option to hold the current state (HOLD)

or to adopt a predefined value if the DMX signal fails.

RDM support

The DMX-LED-Dimmer CC1 the configuration via RDM or DMX.

Top hat rail mounting available

Suitable for the DMX-LED-Dimmer CC1 the DIN rail housing 350 is available as

accessory.

DMX-LED-Dimmer CC1 3

Data sheet

Power supply: 9-48V DC

20mA@12V; 11mA@24V; 6mA@48V

(current consumption without LED-Driver)

Protocol: DMX512

RDM

DMX channels: 1 Channel

DMX-FAIL: HOLD / 0-100%

Output: 1 current limited dimmable LED-Output

Output current according to used

constant current-module

PWM-Frequency: 244 Hz

Dimensions: 29,2mm x 82mm

Constant current-module are not included in delivery !

DMX-LED-Dimmer CC1 4

Connection

DMX-LED-Dimmer CC1

GND

DMX-

DMX+

ADDRESS

DMX OUT

8-48V

GND

9-48V

DMX IN

OUT-

OUT+

DMX-LED-Dimmer CC1 5

LED-Display

The integrated green LED is a multi-function display.

During the normal operation the LED lights permanently. In this case the device is

working.

Furthermore, the LED shows the current status. In this case the LED lights up in

short pitches and then is missing for longer time.

The number of the flashing lights is equal to the event number.

Status

Number

Error

Description

2 No DMX No DMX-Signal is recognized

3 Addressing error Please check the adjusted DMX address

DMX-Addressing

The start address is adjustable via the DIP-switches.

Thereby switch 1 has the valency 2

(=1), switch 2 the valency 2

(=2) and so on until

switch 9 has the valency 2

(=256). The switches showing ON represent in sum the

starting address.

In total all switches showing ON represent the starting-address.

Address

Switch Address

Switch

... ...

508

509

510

511

DMX-LED-Dimmer CC1 6

Constant current-modules

The following constant current-modules are available as accessory for the DMX-LED-

Dimmer CC1:

- Constant current LED-Driver LDD-300H (300mA)

- Constant current LED-Driver LDD-350H (350mA)

- Constant current LED-Driver LDD-500H (500mA)

- Constant current LED-Driver LDD-600H (600mA)

- Constant current LED-Driver LDD-700H (700mA)

- Constant current LED-Driver LDD-1000H(1000mA)

- Constant current LED-Driver LDD-1200H(1200mA)

- Constant current LED-Driver LDD-1500H(1500mA)

Plug the constant current module in such way, that the output of the module (Vout)

points to the screw terminals:

DMX-LED-Dimmer CC1 7

Setting the operating modes

Der DMX-LED-Dimmer CC 1 has several operating modes (MODE) set as follows:

•Turn on the device

•Set switch 9 and 10 on ON

•Set switch 10 on OFF

•Adjust the operating mode via switch 1-8

•Set switch 9 on ON

•Set switch 10 on OFF

•The LEDs lights up 4x to confirm for takeover

•Set about switch 1-9 the DMX-address

Switch 7 OFF: DMX-FAIL ALL ON not active

Switch 7 ON: DMX-FAIL ALL ON active

Switch 8 OFF: DMX-HOLD not active

Switch 8 ON: DMX-HOLD active

DMX-LED-Dimmer CC1 8

DMX-FAIL Function

The DMX-LED-Dimmer CC1 has a DMX-FAIL Function, which stores the last value

after a DMX-Signal failure. This function leaves the output unchanged (HOLD) or

activated with 100% (ALL ON).

A power failure occurs that the last value will be rejected !

If the DMX-HOLD Function is not activated so through the output 0% will be

outputted.

The DMX-HOLD Function can be activated via switch 7 and 8 during the operating

mode adjustment:

Switch 7 OFF DMX-FAIL ALL ON not active

Switch 7 ON DMX-FAIL ALL ON active

Switch 8 ON DMX-HOLD active

Switch 8 OFF DMX-HOLD not active

Via the RDM parameter DMX_FAIL_MODE the level can be adjusted

also.

DMX-LED-Dimmer CC1 9

RDM

(up to Hardware V1.3 with Firmware V1.3 or higher)

RDM is the shortcut for Remote Device Management.

As soon as the device is in the system, device-dependent settings can be made

remotely via RDM command due to the uniquely assigned UID. A direct access to the

device is not necessary.

If the DMX start address is set via RDM, all address switches at the DMX-LED-

Dimmer CC1 must be set to OFF ! A DMX start address set via the address

switches always has priority !

This device supports the follwoing RDM commands:

Parameter ID

Discovery

Command

SET

Command

GET

Command

ANSI/

PID

DISC_UNIQUE_BRANCH



E1.20

DISC_MUTE



E1.20

DISC_UN_MUTE



E1.20

DEVICE_INFO



E1.20

SUPPORTED_PARAMETERS



E1.20

PARAMETER_DESCRIPTION



E1.20

SOFTWARE_VERSION_LABEL



E1.20

DMX_START_ADDRESS



E1.20

DEVICE_LABEL



E1.20

MANUFACTURER_LABEL



E1.20

DEVICE_MODEL_DESCRIPTION



E1.20

IDENTIFY_DEVICE



E1.20

FACTORY_DEFAULTS



E1.20

DMX_PERSONALITY



E1.20

DMX_PERSONALITY_DESCRIPTION



E1.20

DMX_FAIL_MODE



E1.37

SERIAL_NUMBER



PID:

0xD400

1) Manufacturer depending RDM control command (MSC - Manufacturer Specific Type)

DMX-LED-Dimmer CC1 10

Manufacturer depending RDM control command:

SERIAL_NUMBER

PID: 0xD400

Outputs a text description (ASCII text) of the device serial number.

GET Send: PDL=0

Receive: PDL=21 (21 Byte ASCII-Text)

Indice

Altri manuali DMX4ALL Controllori

DMX4ALL

DMX4ALL ArtNet-LED-Dimmer 4 MK2 Manuale utente

DMX4ALL

DMX4ALL ArtNet PixxControl PX2 Manuale utente

DMX4ALL

DMX4ALL DMX-LED-Dimmer 4 Manuale utente

DMX4ALL

DMX4ALL DMX-LED-DIMMER X9 HR Manuale utente

DMX4ALL

DMX4ALL AuroraDMX Control Manuale utente

DMX4ALL

DMX4ALL ArtNet Multi PixxControl Manuale utente

DMX4ALL

DMX4ALL DMX-LED-Dimmer BB4 Manuale utente

DMX4ALL

DMX4ALL ArtNet Player 4 Manuale utente

DMX4ALL

DMX4ALL DMX MultiPixx Control Manuale utente

DMX4ALL

DMX4ALL DMX-LED-DIMMER X9 HR Manuale utente

DMX4ALL

DMX4ALL ArtNet Player X4 Istruzioni per l'installazione e il funzionamento

DMX4ALL

DMX4ALL ArtNet Player X16+ Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente