Doosan DB33A Manuale utente
Service Manual
Diesel Engine
3.3 Liter (DB33A)
SB2013E02
May. 1998
Important Safety Information
Most accidents involving product operation, maintenance and repair are caused by failure to observe basic safety
rules or precautions. An accident can often be avoided by recognizing potentially hazardous situations before an
accident occurs. A person must be alert to potential hazards. This person should also have the necessary train-
ing, skills and tools to perform these functions properly.
Read and understand all safety precautions and warnings before operating or performing lubrication,
maintenance and repair on this product.
Basic safety precautions are listed in the ÒSafetyÓ section of the Service or Technical Manual. Additional safety
precautions are listed in the ÒSafetyÓ section of the owner/operation/maintenance publication.
Specific safety warnings for all these publications are provided in the description of operations where hazards
exist. WARNING labels have also been put on the product to provide instructions and to identify specific hazards.
If these hazard warnings are not heeded, bodily injury or death could occur to you or other persons. Warnings in
this publication and on the product labels are identified by the following symbol.
Improper operation, lubrication, maintenance or repair of this product can be dangerous and could result
in injury or death.
Do not operate or perform any lubrication, maintenance or repair on this product, until you have read
and understood the operation, lubrication, maintenance and repair information.
Operations that may cause product damage are identified by NOTICE labels on the product and in this publica-
tion.
DAEWOO cannot anticipate every possible circumstance that might involve a potential hazard. The warnings in
this publication and on the product are therefore not all inclusive. If a tool, procedure, work method or operating
technique not specifically recommended by DAEWOO is used, you must satisfy yourself that it is safe for you
and others. You should also ensure that the product will not be damaged or made unsafe by the operation, lubri-
cation, maintenance or repair procedures you choose.
The information, specifications, and illustrations in this publication are on the basis of information available at the
time it was written. The specifications, torques, pressures, measurements, adjustments, illustrations, and other
items can change at any time. These changes can affect the service given to the product. Obtain the complete
and most current information before starting any job. DAEWOO dealers have the most current information avail-
able.
WARNING
TO THE CUSTOMERS
This operation and maintenance manual is designed to serve as a reference for DHI's customers and distributors
who wish to gain basic product knowledge on DHI's DB33 Diesel engine.
To maintain the engine in optimum condition and retain maximum performance for a long time, CORRECT
OPERATION and PROPER MAINTENANCE are essential.
In this manual, the following symbols are used to indicate the type of service operations to be performed.
Removal
Installation
Disassembly
Reassembly
Align the marks
Directional Indication
Inspection
Measurement
Adjustment
Cleaning
Pay close attention-Important
Tighten to specified torque
Use special tools of manufacturer's
Lubricate with oil
Lubricate with grease
If you have any question or recommendation in connection with this manual, please do not hesitate to contact our
head office, dealers or authorized service shops.
CONTENTS
1. GENERAL INFORMATIONS 1
1.1. General Repair Instructions 1.4. Major Parts Fixing Bolts
1.2. Engine Specifications 1.5. Engine Repair Kit
1.3. Torque Specifications 1.6. Repair
2. ENGINE ASSEMBLY 19
2.1. General Description 2.3. Inspection and Repair
2.2. Disassembly 2.4. Reassembly
3. LUBRICATING SYSTEM 61
3.1. General Description 3.3. Oil Filter
3.2. Oil Pump 3.4. Oil Cooler
4. COOLING SYSTEM 66
4.1. General Description 4.3. Thermostat
4.2. Water Pump
5. FUEL SYSTEM 70
5.1. General Description 5.3. Injection Nozzle
5.2. Fuel Filter
6. SPECIAL TOOL LIST 74
•WORLDWIDE NETWORK
CONTENTS
1. GENERAL INFORMATIONS 1
1.1. General Repair Instructions 1.4. Major Parts Fixing Bolts
1.2. Engine Specifications 1.5. Engine Repair Kit
1.3. Torque Specifications 1.6. Repair
2. ENGINE ASSEMBLY 19
2.1. General Description 2.3. Inspection and Repair
2.2. Disassembly 2.4. Reassembly
3. LUBRICATING SYSTEM 61
3.1. General Description 3.3. Oil Filter
3.2. Oil Pump 3.4. Oil Cooler
4. COOLING SYSTEM 66
4.1. General Description 4.3. Thermostat
4.2. Water Pump
5. FUEL SYSTEM 70
5.1. General Description 5.3. Injection Nozzle
5.2. Fuel Filter
6. SPECIAL TOOL LIST 74
•WORLDWIDE NETWORK
CONTENTS
1. GENERAL INFORMATIONS 1
1.1. General Repair Instructions 1.4. Major Parts Fixing Bolts
1.2. Engine Specifications 1.5. Engine Repair Kit
1.3. Torque Specifications 1.6. Repair
2. ENGINE ASSEMBLY 19
2.1. General Description 2.3. Inspection and Repair
2.2. Disassembly 2.4. Reassembly
3. LUBRICATING SYSTEM 61
3.1. General Description 3.3. Oil Filter
3.2. Oil Pump 3.4. Oil Cooler
4. COOLING SYSTEM 66
4.1. General Description 4.3. Thermostat
4.2. Water Pump
5. FUEL SYSTEM 70
5.1. General Description 5.3. Injection Nozzle
5.2. Fuel Filter
6. SPECIAL TOOL LIST 74
•WORLDWIDE NETWORK
CONTENTS
1. GENERAL INFORMATIONS 1
1.1. General Repair Instructions 1.4. Major Parts Fixing Bolts
1.2. Engine Specifications 1.5. Engine Repair Kit
1.3. Torque Specifications 1.6. Repair
2. ENGINE ASSEMBLY 19
2.1. General Description 2.3. Inspection and Repair
2.2. Disassembly 2.4. Reassembly
3. LUBRICATING SYSTEM 61
3.1. General Description 3.3. Oil Filter
3.2. Oil Pump 3.4. Oil Cooler
4. COOLING SYSTEM 66
4.1. General Description 4.3. Thermostat
4.2. Water Pump
5. FUEL SYSTEM 70
5.1. General Description 5.3. Injection Nozzle
5.2. Fuel Filter
6. SPECIAL TOOL LIST 74
•WORLDWIDE NETWORK
1
1. GENERAL INFORMATION
1.1. General Repair Instructions
1. For safety, park the truck on even ground or work station and fix the wheels using wedges and hand brake
during operation.
2. Before performing service operations, disconnect the grounding cable from the battery to reduce the chance
of cable damage and burning due to short-circuiting.
3. Before performing service operations release the air pressure in the machine air line system for safety. To not
do so is extremely dangerous.
4. Use covers to prevent the components from damage or pollution.
5. Brake oil and anti-freeze solution must be handled with reasonable care as they cause paint damage.
6. The use of proper tools and special tools where specified is important for efficient and reliable service
operation.
7. Use genuine DAEWOO parts exclusively.
8. Used cotter pins, gaskets, O-rings, oil seals, lock washers and self-lock nuts should be discarded and new
ones should be prepared for installation as normal function of the parts can not be maintained if these parts
are reused.
9. To facilitate proper and smooth reassembly operation, keep disassembled parts neatly in groups. Keeping
bolts and nuts separate is very important as they vary in hardness and design depending on the position of
installation.
10. Clean the parts before inspection or reassembly. Also clean oil ports, etc. using compressed air to make
certain they are free from restrictions.
11. Lubricate rotating and sliding faces of parts with oil or grease before installation.
12. When necessary, use a sealant on gaskets to prevent leakage.
13. Carefully observe all specifications for bolts and nuts torques.
14. When a service operation is completed, make a final check to ensure that the service has been done
properly.
2
1.2. Engine Specifications
Engine Model
Items
Engine type Water-cooled, 4 cycle in-line, overhead valve type
Combustion chamber type Direct injection type
Cylinder liner type Dry type, casting liner
Timing gear system Gear drive type
No. of piston ring Compression ring 2, oil ring 1
No. of cylinder-bore¡¿stroke (mm) 4-102¡¿100
Total piston displacement (cc) 3,268 (199 cu in)
Compression ratio 17.5 : 1
Engine dimension(length¡¿width¡¿height) (mm) 795¡¿701¡¿720 (31¡¿28¡¿28 in)
Engine weight(dry) (kg) 340 (750 lbs)
Fuel injection order 1-3-4-2
Fuel injection timing(B.T.D.C static) 13¡˘
Type of fuel used High-speed diesel fuel (SAE No.2)
Injection pump type VE (DOOWON)
Governor type Mechanical governing
Injection nozzle type Multi-hole type (6 hole) - VCO nozzle
Fuel injection pressure (Kg/cm2) 220 (3,128 psi)
Compression pressure (kg/cm2) 30 (at 200 RPM) (426 psi)
Low idle speed (R.P.M) 775-825
High idle speed (R.P.M) 2400-2500
Intake and exhaust valve clearance(at cold) (mm) 0.4
Lubrication method Pressurized circulation
Oil pump type Gear type
Oil filter type Full-flow type
Lubricating oil capacity (§⁄) 7.5 (Oil pan) (1.97 gal)
Oil cooler type Water cooled
Cooling method Pressurized circulation
Cooling water capacity(engine only) (§⁄) 7.5 (1.97 gal)
Thermostat type Wax pallet type (with jiggle valve)
Generator voltage-capacity(V-A) 12-61
Starter Voltage-output(V-KW) 12-2.5
Intake valve
Exhaust valve
Open at 28 (B.T.D.C)
Close at 62 (A.B.D.C)
Open at 70 (B.B.D.C)
Close at 28 (A.T.D.C)
DB 33A
3
1.3. Torque Specifications
¡Standards bolts
The torque values given in the following table should be applied where a particular torque is not specified.
(Unit : kgƒUm)
Bolt
identification
Bolt
diameter¡¿pitch 4T
Low carbon steel
7T
High carbon steel
9T
Alloy steel
6¡¿1.0
8¡¿1.25
10¡¿1.25
¡10¡¿1.5
12¡¿1.25
¡12¡¿1.75
14¡¿1.5
¡14¡¿2.0
16¡¿1.5
¡16¡¿2.0
18¡¿1.5
20¡¿1.5
22¡¿1.5
24¡¿2.0
0.4-0.8
0.8-1.8
2.1-3.5
2.0-3.4
5.0-7.5
4.6-7.0
7.8-11.7
7.3-10.9
10.6-16.0
10.2-15.2
15.4-23.0
21.0-31.6
25.6-42.2
36.6-55.0
0.5-1.0
1.2-2.3
2.8-4.7
2.8-4.6
6.2-9.3
5.8-8.6
9.5-14.2
9.0-13.4
13.8-20.8
13.2-19.8
19.9-29.9
27.5-41.3
37.0-55.5
43.9-72.5
-
1.7-3.1
3.8-6.4
3.7-6.1
7.7-11.6
7.3-10.9
11.6-17.4
10.9-16.3
16.3-24.5
15.6-23.4
23.4-35.2
32.3-48.5
43.3-64.9
56.5-84.7
The ¡indicates that the bolts are used for female-threaded parts that are made of soft materials such as casting, etc.
4
1.4. Major Parts Fixing Bolts
¡Cylinder head and block
(unit : kgƒUm)
15.2 lb¡⁄ft
2.1
10.0
11.5
2.5
5.3
72.32 lb¡⁄ft
83.17 lb¡⁄ft
18.0 lb¡⁄ft
38.33 lb¡⁄ft
5
¡Intake and exhaust manifold
(unit : kgƒUm)
15.2 lb¡⁄ft
2.1
2.1
15.2 lb¡⁄ft
6
¡Cylinder block and others
(unit : kgƒUm)
2.1
2.6
7.9
2.6
2.4
13.7
Lubricate with engine oil
Lubricate with engine oil
99.1 lb¡⁄ft
15.2 lb¡⁄ft
18.8 lb¡⁄ft
18.8 lb¡⁄ft
57.0 lb¡⁄ft
Indice
Altri manuali Doosan Motore
Doosan
Doosan DE08TS Manuale utente
Doosan
Doosan MD Series Manuale utente
Doosan
Doosan DX22 Manuale
Doosan
Doosan GV158TIC Manuale
Doosan
Doosan D35S-5 Manuale utente
Doosan
Doosan DE08TS Guida rapida
Doosan
Doosan DE08TIS Series Manuale
Doosan
Doosan A2300 Manuale utente
Doosan
Doosan DV11 Manuale utente
Doosan
Doosan PU158TI Manuale
Doosan
Doosan DE12 Series Manuale
Doosan
Doosan D35S-5 Manuale utente
Doosan
Doosan G420F Manuale utente
Doosan
Doosan DE12T Manuale
Doosan
Doosan DP158LCF Manuale
Doosan
Doosan DL06 Manuale utente
Doosan
Doosan D1146 Manuale del proprietario
Doosan
Doosan DP158L Series Manuale
Doosan
Doosan DV11 Manuale utente
Doosan
Doosan G430 LP Manuale utente
