DPVR E3 Polaris Kit Manuale utente
DPVR E3 Polaris Kit
User Manual
Version 1.3-20171228
1. Unpacking
2. Headset
3. Polaris base station
4. Polaris controller
5. First use of the product
6. Configurations of the headset, controller and base station
7. Steam
Package contents
Introduction
Wearing the headset
Adjusting headbelt
Headset repair and maintenance
Headset indicators
Connecting earphone and microphone to headset via the
audio cable
Introduction
Base station usage scenario
Polaris base station indicators
Introduction
Button mapping
Recharging the Polaris controller
Polaris controller turning on/off, standby and waking up
Mounting Strap on the Polaris controller
Indicators on the Polaris controller
Download the DpnAssistant
Check computer configuration
Novice wizard
Connect the headset and computer
Headset firmware upgrade
Load base station parameters
Upgrade base station firmware
Mount the base station positioning base station
Pairing the polaris controller and upgrading the controller
firmware
Base station calibration purpose
Base station coverage
Preparations for base station calibration
Base station calibration
What is the Steam?
What is the Steam VR?
Steam download and installation
How to perform room setup in Steam VR
In the Steam, how to open an non-Steam game downloaded
locally?
1
1
1
1
3
4
4
6
6
7
7
8
9
9
9
10
11
12
12
12
13
13
13
16
17
18
18
19
22
23
27
30
30
31
31
43
43
43
43
43
45
CONTENTS
8. Gaming zone
9. Troubleshooting
10. Contact us
11. Brand and copyright
What is the gaming zone?
Plan the gaming zone
Choose the gaming zone
Set up Standing Only gaming zone
Set up Room Scale gaming zone
Reset gaming zone
Verify setup
What to do if no Polaris controller is detected?
What to do if the indicator of the Polaris controller is off?
What to do if I disconnect the Polaris controller accidentally
during the firmware upgrade and cannot start up any more?
What to do if the headset cannot be traced?
What to do if the headset display is fuzzy?
What to do when I get the error “Failed to detect the DP
headset. Please check the connection?”
What to do if “HDMI disconnected” is shown in the Device
Connect of the DpnAssistant?
What to do if “USB disconnected” is shown in the Device
Connect of the DpnAssistant?
What to do when no sound is heard by using the audio cable?
Is it possible to play the VR audio from the computer at the
same time?
What to do if the base station calibration failed?
What are the warranty policies in case of accidental damage
with the Polarisbase station?
What to do when my TV remote control does not work while
the E3 Polaris is in use?
Health Tip
46
46
46
47
48
49
49
50
51
51
51
51
52
52
52
52
53
53
53
54
54
54
55
55
56
1
Package contents
Remarks: The positioning set (180º) is a single base station
configuration, including one base station, one base station power
supply and one accessory kit.
The positioning set (360º) is a dual base station configuration,
including two base stations, two base station power supplies and
two accessory kits.
The headset is the window bringing you into the virtual reality (VR)
environment. It includes sensors that are traceable by the Polaris
base station.
Hint: The headset includes several laser sensors inside. In order
they can receive well laser signals from the base stations, do not
cover the headset surface with any extra materials. In addition, keep
your hands or other items from blocking the location of the headset
sensors during usage.
1. Unpacking
introduction
2. Headset
Main device Accessories
3-in-1 cable (installed)
Audio cable (installed)
Back foam cushion
Lens cloth
Calibrator
Controller charger (x2）
USB cable (x2), i.e. USB to Micro-USB cable
Strap (x2）
Base station power supply*
Base station installation accessory kit *
DPVR E3 Polaris
Polaris controller (x2)
Polaris base station*
2
Back Foam Cushion
Head Strap
Face Foam Cushion
Optical Lens
Baffler
Mic In
Audio Cable
3-in-1 Cable
Cable Cover
DPVR Logo/
Pilot Lamp
Pictures:
3
Fig. 1 Press the facial foam of the headset against
your glasses, and then pull the headband.
Fig. 2 Enclose the glasses with the facial foam, loosen
the headband and adjust to a confortable position.
Wearing the headset
For glasses-free users, just wear the headset and adjust it to a
comfortable position.
For users with glasses, please follow these instructions to wear the
headset:
4
Velcro loop
Velcro hook
Adjusting strap
The device comes with a headbelt which adapts to user’s head
circumference automatically through its elastic structure. If the head
circumference is too small and the headset may easily fall down due
to loose headbelt, please use the head buffer. If the head circumfer-
ence is big enough, the back foam cushioningis not necessary.
Headset repair and maintenance
Servicing the E3 headset
The following instructions are used for servicing your E3 headset.
• Keep the headset away from sharp items such as cable tip, in case
the headset lens be scratched.
• During use or storage, avoid direct irradiation from strong sunshine
or other light sources on the lens lest the product be damaged.
• When the headset is in storage, we recommend using protective
film on the lens to prevent accidental scratching.
Cleaning headset lens
• To wipe the lens, always use the lens cloth provided in the package.
• Dip the lens cloth in alcohol or special detergent.
• Wipe in circularity from the center to edge.
• While cleaning the lens, do not scratch the lens or remove other
parts of the headset.
5
Facial contact surfece
HOOK&LOOP
The cable cover contains screw
tighteners!Pry the screw stud
and remove the screws with a
screwdriver. Insert a straight
screwdriver beneath the cable
and prize up the cable.
Warning: Products from different batches may need different cable
replacement methods. If the cable cover has screws, unscrew the
two screws first with a screwdriver before removing the cable cover.
Replacement for helmet cables
For headset with screws: To replace the 3-in-1 cableor audio cable ,
firstly unscrew the screws, prize up the cable cover by using a small
screwdriver, draw out the old cable and insert a new one. Finally
resume the cable cover and tighten the screws.
Replacing cable step 1
After use for a long time, the facial foam may be worn and needs to
be replaced when necessary.
1. Peel off the facial foam gently from the nose area.
2. Install the new facial foam as shown in the figures below and press
it gently onto the headset.
Replace the facial foam
6
Push the cablie into
the cable ties and
fixing ring.
Replacing cable step 2
For headset without screws: To replace the 3-in-1 cable or audio
cable, prize up the cable cover by using a small screwdriver, draw out
the old cable and insert a new one. Finally resume the cable cover.
Headset indicators
Blue on: Headset is in normal work
Blue flash: Headset is in standby.
Green: Headset is in magnetic calibration process.
Connecting earphone and microphone to headset via the
audio cable
After the audio cable of the headset is connected to an earphone:
1. Select Playback Device from the right-click menu of the sound
icon from the bottom-right corner of computer desktop. The audio
setup window appears.
2. In the audio setup window, choose the desired audio output port,
such as DPVR E3. Click Set as Default.
7
Front:
Indicator
Side:
LOGO(upward)
Back:
Power jack
USB socket
Master/slave switch
Base station mounting hole (upper)
Base station mounting hole (lower)
Introduction
Hint: The Polaris base station sends signals to the headset and
controller. Keep the front panel from being blocked by anything.
When the Polaris base station is turned on, it may interfere with
some infrared sensors nearby, such as the sensor in TV remote
control.
Warning: The base station includes precision components which are
subject to damage in case of drop or impact. Use or store it carefully!
Hint: Do not open the cover of the Polaris base station, because that
may cause harm to you or your product.
Please stop using the Polaris base station if its front panel is broken.
3. Polaris base station
Indice
