DR. Heater DR-908 Manuale utente

Wall Hung Infrared Heater

•1500 Watts with

Two Heat Settings

•Thermal Cutoff Protection

•Tip-Over Switch

•Room Temperature

LED Display

•Precision Temperature

Control

•Easy Push-Button Controls

•Advanced Dual Heating System (ADHS)

•With foldable leg which can be used on floor application

Owner’s Manual

PLEASE READ AND

SAVE THESE INSTRUCTIONS

Model No.: DR-908

CONGRATULATIONS!

he Dr. Infrared Heater you have just purchased is a

safe and powerful heater, designed to heat a room after a few minutes of

operation. The far-infrared Quartz-PTC heating system is an excellent

choice for safely heating whole room, while saving on heating costs.

Additionally, this heater includes an overheat protection system, and an inlet air

overheat protection system designed to ensure your safety.

This heater does not reduce humidity or oxygen in your home or office,

promoting a healthier environment!

Before using your Dr. Infrared Heater, please take a few minutes to read these

instructions, and review the product’s limited warranty.

Thank you!

CAUTION- High temperature! Keep electrical cords, drapery, and other

furnishings at least 3 feet (0.9 m) from the front and rear of the heater.

IMPORTANT

INSTRUCTIONS

When using this appliance, basic precautions should always be followed to

reduce the risk of fire, electric shock, and injury to persons, including the

following.

1. Read all the instructions before using this heater.

2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot

surfaces. Use handle when moving this heater. Keep combustible materials,

such as furniture, pillows, bedding, papers, clothes, and curtains at least 3

feet (0.9 m) from the front of the heater and keep them away from the sides

and rear.

3. Extreme caution is necessary when any heater is used by or near children

or persons with physical challenges and whenever the heater is left

WARNING! To reduce the risk of fire, electric shock, or personal injury, read

all the instructions before using this heater. This appliance is intended for

household or personal use only as described in this manual. Any other use

including but not limited to commercial, agricultural, or outdoor use, is not

recommended by the manufacturer and may cause fire, electric shock, injury

and/or damages. The use of any attachments and/or accessories not

recommended or sold by Dr. Infrared Heater Products may cause hazards and

void the warranty.

operating and unattended.

4. Do not operate the heater with a damaged cord or plug, or after the heater

malfunctions, has been dropped, or damaged in any manner. Return the

heater to an authorized service facility for examination, electrical or

mechanical adjustment, or repair.

5. Do not use outdoors.

6. This heater is not intended for use in bathrooms, laundry areas or similar

locations. Never locate the unit where it may fall into a bathtub or other

water container.

7. Do not run the cord under carpeting and do not cover the cord with throw

rugs, runners or the like. Do not route cord under furniture or appliances.

Arrange the cord away from traffic areas to avoid a tripping hazard.

8. To disconnect the heater, turn controls to OFF, then remove the plug from

outlet.

9. Do not insert or allow foreign objects to enter any ventilation or exhaust

opening as this may cause an electric shock, or fire, or damage to the

heater.

10. Connect to properly grounded outlets only.

11. To prevent a possible fire, do not block air intakes or exhaust openings in

any manner. Do not use on soft surfaces, like a bed, where openings may

become blocked. Use the heater on flat, dry surfaces only.

12. A heater has hot and arcing or sparking parts inside. Do not use the heater

in areas where gasoline, paint or flammable liquids are used or stored.

13. Use this heater only as described in this manual. Any other use not

recommended by the manufacturer may cause fire, electric shock, or injury

to persons.

14. Never clean this heater while it is plugged in. Do not immerse in water. To

disconnect, turn control to OFF, then remove the plug from the outlet by

grasping it and pulling it from the outlet. Never yank on the cord.

15. Always unplug the heater when it is not in use.

16. Always plug heater directly into a wall outlet/receptacle. Never use with an

extension cord or relocatable power tap (outlet/power strip).

17. It is normal for the heater’s plug and cord to feel warm to the touch. A plug

or cord which becomes hot to the touch or becomes distorted in shape may

be a result of a worn electrical outlet. Worn outlets or receptacles should be

replaced prior to further use of the heater. Plugging this heater into a worn

outlet may result in overheating of the power cord or fire.

18. Make sure the plug is fully inserted into an appropriate receptacle. Be

mindful that receptacles also deteriorate due to aging and continuous use.

Check periodically for signs of overheating or deformations of the plug. If

any overheating or deformation occurs, immediately discontinue using the

heater and contact Dr. Infrared Heater Authorized Service Center.

19.CHECK YOUR HEATER CORD AND PLUG CONNECTIONS. Faulty wall

outlet connections or loose plugs can cause the outlets or plug to overheat.

During use, please check frequently to determine if your plug outlet or

faceplate is HOT! If it is hot, discontinue using the heater and/or make

certain a qualified electrician checks and replaces the faulty outlet(s).

CAUTION: This appliance is not intended for use by persons (including children) with

reduced physical, sensory or mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction concerning use of the appliance

by a person responsible for their safety.

SAVE THESE INSTRUCTIONS

Product Specifications

Voltage Rating

120V (60Hz)

Power Consumption

1500W

Unit Size

15-17/64 in. (H) x 11-21/64 in. (W)

x 6-21/64 in. (D)

Unit Weight

8.46 lbs.

Special Features

LED Display – When the unit is plugged in, the POWER LED will light. To turn

the heater ON, press the MODE button, the heater will wait in ECO Mode. At

ECO mode, it will display the set value 2 minutes after the desired temperature

is set.

Overheat Cut-Off Protection System –This heater includes a protection system

that cuts off the unit if it overheats for any reason.

Inlet Air Overheat Protection System – This heater will automatically cut off if

the inlet air duct becomes obstructed and causes the unit to overheat.

Safety Tip-Over Switch – The Dr. Infrared Heater is designed to cut off

automatically when tipped in any direction. Place the heater on a flat, smooth,

stable surface to prevent the heater from tipping over again. When returned to

a normal upright position, the heater is ready for use again. This is a safety

feature to avoid the possibility of fire should the unit be tipped accidentally.

Advanced Dual Heating System (ADHS) - Dr. Heater is the first to feature a

dual heating system for maximum heat transfer rate. It combines the energy

efficiency of infrared heat with the comfort of convection heat to heat your room

fast and comfortably—without hot spots and cold spots.

Features

A. “Cool-Touch” cabinet E. LED temperature display

B. POWER LED F. Increase temperature button

C. ON/OFF button G. Decrease temperature button

D. MODE button

Installation Instructions

This heater has foldable legs which can be used on floor application. It can also

be mounted on the wall.

On the Floor

Open wide the foldable legs and the unit can stand freely on the floor.

On the wall

1.Drill the required holes with the ST4x20 screws (Included) as below.

Legs Closed

(Bottom View)

Legs Opened

(Bottom View)

Side View

Rear View

2.Hang up the heater with the hanging hole to the screws.

Operating Instructions

1. Plug the power supply cord into a grounded wall outlet. (120VAC,

60Hz)

IMPORTANT: This heater is for use on 120 volts. This heater comes with a

grounded (three-prong) plug. The grounded plug must be used with a

grounded outlet. Do not used an adapter in two-slot wall outlet unless the

grounded plug of the adapter properly connects to a building ground. Using the

heater without a properly grounded outlet or adapter could result in an electric

shock hazard.

Hanging hole

The cord has a plug as shown at

A in the following figure. An adapter,

as shown at C, is available for

connecting three-blade grounding

type plugs to two-slot receptacles

The green grounding lug extending

from the adapter must be

connected to a permanent ground

such as a properly grounded outlet

box. The adapter should not be

used if a three-slot grounded

receptacle is available.

2. TURNING THE HEATER ON

3. Plug in unit to power outlet，the POWER LED will light. To turn the heater ON,

press the MODE button, the heater will wait in ECO Mode.

4. HEATING MODES

Press the MODE button to toggle between the different modes: ECO, HIGH,

LOW. Heater exit from any mode to standby mode by pressing the

STANDBY button.

5. ECO MODE – 1500W/1000W

ECO mode is a computerized mode to optimize energy efficiency. It will

programmatically select between HIGH and LOW power mode to heat up

the room to the desired temperature in the most effective way. Once the

desired temperature is achieved, the heater will maintain the room to the set

temperature. ECO mode is the environmentally friendly operating mode.

6. HIGH POWER MODE – 1500W

HIGH mode will control the heater to operate at high power until the room

reached the set temperature. The heater will stop heating and initiate

component cooling process before turning off the fan. Once the desired

temperature is achieved, the heater will maintain the room to the set

temperature.

7. LOW POWER MODE – 1000W

LOW mode will control the heater to operate at low power until the room

reached the set temperature. The heater will stop heating and initiate

component cooling process before turning off the fan. Once the desired

temperature is achieved, the heater will maintain the room to the set

temperature.

8. SETTING THE TEMPERATURE

Choose the desire Mode: ECO, HIGH, or LOW. To set the desired

temperature:

Press the button once

until the numeric temperature starts flashing.

Press the button again to increase the temperature or the button to

decrease the temperature.

Once the temperature is set, the heater will warm up the room using the selected

Mode. Heater will sample the room temperature every 4 minutes after the

desired temperature is reached.

9. Night Mode

Night mode is design for quiet operation in the night. When the surrounding

environment becomes dark, or the heater can't detect the light, it will turn

into the Night Mode automatically. In this mode, when the heater reached

the set temperature, it will sample the room temperature less frequently, 30

minutes per sample. When the heater detects the light, it will turn into the

ECO Mode automatically.

10. Display the room temperature

The display shows the set temperature all the time, press and hold the

MODE button and then press the button. The room temperature will

display for 30 seconds. It will return to set temperature after 30 seconds.

11. Display Celsius

To display Celsius, press and hold the MODE button for 2 seconds. Press

and hold the MODE button for 2 seconds again to change back to

Fahrenheit.

Remote Controller

HOW TO INSERT BATTERIES

NOTE: Remove the batteries if the remote control is not to be used for a month

or more. Batteries left in the unit may leak and cause damage.

DO NOT MIX OLD AND NEW BATTERIES IN USE! DO NOT MIX ALKALINE,

STANDARD (CARBON-ZINC) OR RECHARGEABLE (NICKEL-CADMIUM)

BATTERIES IN USE!

Instructions for the Use of the IR Remote Control

The buttons on the remote controller functions in the same manner as those on

the control panel on the front of the heater. Set the timer by using the remote

control.

Setting the Timer

1. Press the TIMER button until Set Time starts flashing. The default value is 3

hours.

2. Press the “+” button to increase the

set time or the “–” button to decrease the set time.

The timer can be set from

1 to 12 hours. The timer will set and execute after the LED display stops

flashing. The heater will shut OFF automatically when the set time is

reached.

3. To turn the timer OFF, follow step 1,

pressing the “–” button to set the

time to 0. The timer feature will turn off when the LED stops flashing.

Maintenance

1. Always turn OFF the heater and disconnect the cord from the electrical

outlet before cleaning the unit.

2. Light accumulation of dust may be removed from the heater with a soft cloth

or vacuum cleaner.

3. Wipe the exterior surfaces of the heater occasionally with a damp cloth (not

dripping wet), using a solution of mild detergent and water. Dry the case

thoroughly before operating the heater.

Caution! Do not allow water to run into the interior of the heater as this could

create a fire or electric shock hazard.

4. The fan motor is factory-lubricated for life and will require no further

lubrication.

5. Store the heater in a clean, dry place when it is not in use.

Indice

Altri manuali DR. Heater Stufa

DR. Heater

DR. Heater DR-966 Manuale utente

DR. Heater

DR. Heater DR-966 Manuale utente

DR. Heater

DR. Heater DR-975 Manuale utente

DR. Heater

DR. Heater DR-999 Manuale utente

DR. Heater

DR. Heater DR-910F Manuale utente

DR. Heater

DR. Heater DR-239 Manuale utente

DR. Heater

DR. Heater DR-978 Manuale utente

DR. Heater

DR. Heater DR-928 Manuale utente

DR. Heater

DR. Heater DR-968 Manuale utente

DR. Heater

DR. Heater DR-122X4 Manuale utente

DR. Heater

DR. Heater DR-PS11024 Manuale utente

DR. Heater

DR. Heater DR-910M Manuale utente

DR. Heater

DR. Heater DR-968H Manuale utente

DR. Heater

DR. Heater DR-233 Manuale utente

DR. Heater

DR. Heater DR-988 Manuale utente

DR. Heater

DR. Heater DR-968H Manuale utente

DR. Heater

DR. Heater DR-101 Manuale utente

DR. Heater

DR. Heater DR-222 Manuale utente

DR. Heater

DR. Heater DR-368 Manuale utente

DR. Heater

DR. Heater Elite Series Manuale utente

DR. Heater

DR. Heater DR218-1500 Manuale di istruzioni per l'installazione

DR. Heater

DR. Heater DR-368 Manuale utente

DR. Heater

DR. Heater DR-338 Manuale utente

DR. Heater

DR. Heater DR-238 Manuale utente

Manuali Stufa popolari di altre marche

oventrop

oventrop Regucor Series Manuale utente

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuale utente

ELMEKO

ELMEKO ML 150 Manuale utente

BN Thermic

BN Thermic 830T Manuale utente

KING

KING K Series Guida

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guida rapida

Well Straler

Well Straler RC-16B Manuale utente

EUROM

EUROM 333299 Manuale utente

Heylo

Heylo K 170 Manuale utente

Eterna

Eterna TR70W Manuale utente

Clarke

Clarke GRH15 Manuale di istruzioni

IRSAP

IRSAP The Radiator Company Ovali Manuale utente

Empire Heating Systems

Empire Heating Systems WCC65 Manuale utente

Wetekom

Wetekom 92 86 43 Manuale utente

Desa

Desa SPC170-F Manuale utente

Watlow

Watlow Watrod Electric Tubular Heaters Manuale utente

Haverland

Haverland ECO-DRY GPS Series Manuale elenco delle parti

Stelpro

Stelpro ASILVC2060 Series Manuale utente