Draper DH50 Manuale utente
12498
EN
Original Instructions
Version 1 – May 2023
50L
DEHUMIDIFIER
1.1 Product Reference
User Manual for: Industrial Dehumidier, 50L
Stock No: 12498
Part No: DH50
1.2 Revisions
Version 1: May 2023
First release
As our manuals are continually updated, always ensure
that the latest version is used.
Please visit drapertools.com/manuals for the latest
version of this manual and the associated parts list, if
applicable.
1.3 Understanding the Safety Content of
This Manual
WARNING!
– Situations or actions that may result
in personal injury or death.
CAUTION! – Situations or actions that may result
in damage to the product or surroundings.
Important: – Information or instructions of particular
importance.
1.4 Copyright © Notice
Copyright © Draper Tools Limited.
Permission is granted to reproduce this manual for
personal and educational use ONLY. Commercial
copying, redistribution, hiring or lending is strictly
prohibited.
No part of this manual may be stored in a retrieval system
or transmitted in any other form or means without written
permission from Draper Tools Limited.
In all cases, this copyright notice must remain intact.
1. Preface
– 2 –
These are the original product instructions. This
document is part of the product; retain it for the life
of the product, passing it on to subsequent holders.
Read this manual in full before attempting to
assemble, operate or maintain this product.
This Draper Tools manual describes the purpose
of the product and contains all the necessary
information to ensure its correct and safe use.
Following all the instructions and guidance in
this manual will ensure the safety of both the
product and the operator and increase the
lifespan of the product.
All photographs and drawings within this manual are
supplied by Draper Tools to help illustrate correct
operation of the product.
Every eort has been made to ensure the
information contained in this manual is accurate.
However, Draper Tools reserves the right to amend
this document without prior warning. Always use the
latest version of the product manual.
2. Contents
– 3 –
EN
1. Preface 2
1.1 Product Reference 2
1.2 Revisions 2
1.3 Understanding the Safety Content of This
Manual 2
1.4 Copyright © Notice 2
2. Contents 3
3. Product Introduction 4
3.1 Intended Use 4
3.2 Specication 4
4. Health and Safety Information 5
4.1 Health and Safety Information for this
Dehumidier 5
4.2 Additional Safety Information for Flammable
Refrigerants 6
4.3 Connection to the Power Supply 7
4.4 Residual Risk 7
5. Identication and Unpacking 8
5.1 Product Overview 8
5.2 What’s in the Box? 9
5.3 Packaging 9
6. Preparation Instructions 10
6.1 Assembling the Dehumidier 10
6.2 Selecting a Drainage Mode 10
6.3 Positioning the Dehumidier 11
7. Operating Instructions 12
7.1 The Control Panel 12
7.2 Switching the Dehumidier
On and O 12
7.3 Emptying the Water Tank (Manual Drainage
Mode) 12
7.4 Setting the Target Humidity 13
7.5 Using the Timer 13
7.6 Auto-Defrost Functionality 13
7.7 Overheating Protection 14
8. Maintenance and Troubleshooting 14
8.1 General Maintenance and Storage 14
8.2 Air Filter Care 14
8.3 Air Inlet Care 15
8.4 Water Tank Care 15
8.5 Troubleshooting 15
9. Spares, Returns and Disposal 17
10. Warranty 18
11. Explanation of Symbols 19
3. Product Introduction
– 4 –
3.1 Intended Use
This product is designed to extract moisture from damp
or humid industrial environments to prevent the build-up
of mould and other hazards. Any other application
beyond the conditions established for use will be
considered misuse. Draper Tools accepts no
responsibility for improper use of this product.
Part of our ore range, this product is suitable for regular
use by enthusiasts and tradespersons alike.
Important: This product is not a water pump and is not
designed to transfer water from one location to another.
WARNING! This product is not a toy and must be
respected.
Read this manual in full before attempting to assemble,
operate or maintain the product, and retain it for later
use.
Stock No. 12498
Part No. DH50
Rated frequency 50Hz
Rated power 900W
Rated current 4.0A
Extraction rate 50L per day (at 30°C, 80% relative humidity)
Target humidity range 10–95%
Condensate capacity 7L
Condensate tank outlet Ø12mm
Refrigerant: R290 (propane) 200g
Max. suction pressure 1.0Mpa
Max. discharge pressure 2.5Mpa
Minimum room size 10m2
Ambient operation environment 5–35°C
Global warming potential 3
Ingress protection IP22
Dimensions W 450 × H 655 × D 480mm
Net weight 30kg
3.2 Specication
4. Health and Safety Information
Important: Read all the Health and Safety instructions
before attempting to assemble, adjust, operate or
maintain this product. Non-compliance with these
instructions may result in injury or damage to the user or
the product.
4.1 Health and Safety Information for this
Dehumidier
General Safety Instructions
• Only authorised personnel that have been trained in
the use of this product and are familiar with the
instructions in this manual may operate this machine.
Important: This product is not suitable for use by
children.
• Inspect the product before every use for cracked,
corroded or broken parts and leakages.
WARNING! DO NOT use this product if it is
damaged or leaking in any way. Contact
Draper Tools for repair and replacement
options.
• Use this product only for its intended purpose and do
not modify it in any way.
• DO NOT operate this product while tired or under the
inuence or alcohol, drugs or other medication.
• Keep your hands and other body parts away from
moving parts at all times and keep loose hair, clothing
and jewellery tied back.
• ONLY use spare parts supplied by Draper Tools.
Installation
• DO NOT use or store this product in unventilated
areas that are smaller than the minimum required
space for this product.
• DO NOT use this product in environments containing
high concentrations of dust; ammable, volatile, toxic
or otherwise dangerous gases, vapours and liquids; or
where the air composition is ammable.
• DO NOT use this product in locations in which ames
or sources of ignition are present.
• This product is suitable for indoor use ONLY; DO NOT
immerse it in water or expose it to wet conditions.
• DO NOT use this product in the vicinity of water tanks.
• Keep all air vents and grilles free from obstructions.
• Use this product ONLY on sturdy, at and level
surfaces capable of bearing the weight of the product
and a full water tank.
Important: DO NOT use this product on tilted
surfaces as it may cause damage to the internal
components or cause the unit to tip over.
• Ensure that the product is positioned with no less than
the minimum clearance required around all sides of
the unit during use.
• DO NOT place the product directly beneath wet
materials; allow at least one metre between the unit
and the items to be dried.
Correct Use and Operational Safety
• NEVER connect this product to a power supply if the
air lter is not installed.
• NEVER cover the air vents and grilles or place any
object on the product during use.
• DO NOT insert foreign objects through the air vents or
grilles.
• NEVER open or place your hands inside the product
during use.
• NEVER modify or remove the oat switch from the
water tank.
• ALWAYS switch o the product using the power
button before disconnecting the power supply.
Electrical Safety
• Keep the power cord away from sources of heat,
liquids, oil and hot or sharp surfaces.
• NEVER handle the plug or operate the product with
wet hands.
• NEVER pull the product along using the power cable
or plug and DO NOT pull on the cable to disconnect
the plug from a power supply.
• Position the power cable tidily and safely so that it
does not create a trip hazard.
– 5 –
EN
4. Health and Safety Information
Handling and Storage
WARNING! This product is heavy and requires
two people to lift and transport it. Use
appropriate equipment where necessary. Failure
to transport the product safely may result in
serious injury.
• Switch o the product, disconnect it from the power
supply and wait for all moving parts to stop before
attempting to maintain or move the unit.
• Store and transport the product in an upright
position.
• DO NOT use or store this product in the presence of
ammable liquids or vapours.
• Empty the water tank before transporting the product.
• Discard any liquid accumulated in the water tank; DO
NOT use it for any other purpose.
Servicing
• Any maintenance beyond the procedures detailed in
this manual MUST be performed by an authorised
and suitably qualied technician.
4.2 Additional Safety Information for
Flammable Refrigerants
WARNING! This product contains approximately
200g of pressurised R290 (propane) refrigerant.
This substance is highly ammable and must
NOT be exposed to sources of ignition.
• DO NOT use this product in spaces that are smaller
than the minimum room size rated for the unit.
• By means of ventilation or construction, the space in
which the unit is installed must NOT cause or allow
the refrigerant to stagnate and create a re or
explosion hazard in the event of a leak.
• The unit MUST be stored in a well-ventilated room no
smaller than the minimum room size required for
operation in which no continuously operating open
ames (e.g. an operating gas appliance) and no
sources of ignition (e.g. an operating electric heater)
are present.
• Keep all air vents and grilles in the location and on the
product free from obstructions.
• DO NOT attempt to undertake any maintenance
procedures not covered in this manual; additional
servicing and handling of the refrigerant MUST be
conducted by an authorised and suitably qualied
service agent who is competent in the use and
handling of ammable refrigerants.
• DO NOT puncture, burn or attempt to modify the
refrigerant system or its components in any way.
• DO NOT use any means to accelerate the defrosting
process or to clean other than those identied in this
manual.
WARNING! Refrigerant gases may be odourless
and can explode in the presence of sources of
heat and ignition.
– 6 –
4. Health and Safety Information
4.3 Connection to the Power Supply
WARNING! Risk of electric shock. DO NOT open
this product.
This appliance is supplied with an approved plug and
cable for your safety. The product must be installed
according to national wiring regulations.
If the power supply cord is damaged, it must be replaced
by Draper Tools, an authorised service agent or similarly
qualied personnel in order to avoid a hazard.
The damaged or incomplete plug, when cut from the
cable, must be disabled to prevent connection to a live
electrical outlet.
This product is Class I* and is designed for connection
ONLY to a power supply matching that detailed on the
rating label and compatible with the plug tted.
The value of the fuse tted is marked on the pin face of
the plug. Should the fuse need replacing, ensure the
substitute is of the correct rating, approved to BS 1363/A
and ASTA or BS Kite marked. This should only be
performed by suitably qualied personnel.
ASTA
BSI
The fuse can be replaced by removing the cover using a
small plain slot screwdriver and removing the broken
fuse from its holder. This should only be performed by
suitably qualied personnel.
If an extension lead is required, use an approved and
compatible lead rated for this appliance. Where use of an
extension lead is unavoidable, Draper Tools recommends
using a 2.5mm cable. Follow all the instructions supplied
with the extension lead.
Important: Always follow the extension lead instructions
regarding maximum load while the cable is wound. If in
doubt, unwind the entire cable. A coiled extension lead
generates heat which could melt the lead and cause a
re.
*Earthed: This product requires an earth connection to
protect against electric shock from accessible
conductive parts in the event of a failure of the basic
insulation.
4.4 Residual Risk
The safety instructions in this manual cannot account for
all possible conditions and situations that may occur.
Exercise common sense and caution when using this
product and protect against any additional conceivable
risks.
– 7 –
EN
– 8 –
5. Identication and Unpacking
5.1 Product Overview
(1) Air lter
(2) Air inlet
(3) Control panel
(4) Front feet
(5) Power cable and plug
(6) Transport handle
(7) Water tank
(8) Water tank access panel
(9) Water tank hose port
(10) Wheels
(3) (1)
(6)
(8)
(4)
(7)
(10)
(9)
(5)
(2)
(C)
(I)
(H)
(B)
(F)
(D)
(E)
(D)
– 9 –
5. Identication and Unpacking
5.3 Packaging
Keep the product packaging for the duration of the
warranty period for reference should the product need to
be returned for repair.
WARNING! Keep packaging materials out of
reach of children. Dispose of packaging
correctly and responsibly and in accordance
with local regulations.
†Some or all of these parts may be tted to the dehumidier unit before shipment.
(A) 1 × Dehumidier unit (Not shown)
(B) 1 × Axle
(C) 2 × Wheels
(D) 2 × M6 × 35mm bolts†
(E) 4 × M6 × 28mm bolts
(F) 2 × M12 washers
(G) 2 × M12 nuts
(H) 4 × M6 nuts†
(I) 1 × Ø12mm discharge hose
Please visit drapertools.com for our full range of accessories and consumables.
– 9 –
EN
5.2 What’s in the Box?
Carefully remove the product from the packaging and
examine it for any signs of damage that may have
occurred during shipment.
Before assembling the product, lay the contents out and
check them against the parts shown below. If any part is
damaged or missing, do not attempt to use the product.
Please contact the Draper Helpline; contact details can
be found at the back of this manual.
6. Preparation Instructions
Important: Before assembling and installing this
product, read and understand all the safety instructions
listed in this manual.
6.1 Assembling the Dehumidier
WARNING! This product is heavy. For your
safety, Draper Tools recommends that this
product is assembled by two people.
1. Unfold the transport handle (6) and secure it in place
using the four M6 × 35mm bolts (D) and two M6 nuts
(H).
1 Fig.
(6)
(D)
(H)
2. Carefully tip the dehumidier unit onto its front face.
3. Align the axle (B) with the base of the unit and secure
it in place using the four M6 × 28mm bolts (E).
2 Fig.
(B) (E)
4. Place a wheel (C) onto each end of the axle and secure
them in place using the M12 washers (F) and M12
nuts (G).
3 Fig.
(G) (F)
(C)
(B)
5. Carefully tip the unit into its upright position.
CAUTION! After assembly or tipping the
dehumidier for any reason, allow it to rest in an
upright position for at least 2 HOURS before
connecting it to mains power.
6.2 Selecting a Drainage Mode
The dehumidier features two drainage modes:
• Manual (internal water tank)
• Continuous
Manual Drainage Mode
The dehumidier is supplied with a removable internal
water tank (7) and will automatically operate in manual
drainage mode. When the water tank is full, the unit
switches o automatically until the tank is emptied.
Important: Ensure that the water tank outlet is securely
sealed when operating in manual drainage mode.
– 10 –
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Draper Deumidificatore
