Draper Profile+ Manuale utente
Profile+Permanently Tensioned Projection Screen
Assembly & Mounting Instructions
Profile Components:
Tools Required:
Tape Measure Pencil Hex Head Power Drill Fastening
Screwdriver Hardware
(By others)
Caution
BRead instructions through completely before proceeding.
CFollow instructions carefully.
Installation contrary to instructions invalidates warranty.
DScreen should be accessible for complete removal should fabric
become damaged or should other service be required.
EScreen should be installed level (using a carpenter’s level).
FNothing should be fastened to screen frame or viewing surface.
GMake sure you have received all parts (see parts list below and
exploded diagram on page 3).
HInstaller is responsible for providing appropriate hardware for mounting.
I
Draper recommends using two people for assembly and installation.
When lifting assembled screen, do not lift at only one corner; lift at both
corners. Lifting by one corner could result in damage to the screen
frame, especially on large screens.
JThe ideal temperature range for assembling permanently tensioned
screens to prevent damaging the surface is 68°-78° F (20°-26° C).
Assembling below recommended temperatures may damage surface
and void warranty.
5/32"- Grade 8
Hex Screws
(several)
Mounting
Brackets
Sliding Snap
Attachments
(several)
Sliding
Hook & Loop
Attachment
(several)
Frame Extrusion
Section
Trim Frame
Section
Corner
Vertical Support
Connector
Front
View
Back
View
Copyright © 2016 Draper Inc. Form Profile+_IInst16 Printed in U.S.A.
Trim Frame
Corner
Vertical Support
For Larger Sizes
For Hook and Loop Fabric Attachment:
1-A. Insert sliding Hook & Loop attachments
into all four (4) sections of the frame
(See Fig. 1-A).
For all fabric attachment methods:
2. Insert the Frame sections onto the corners pieces
(See fig 2.) and secure them with provided screws.
5. Carefully lay the screen fabric down on a clean surface. Place
the assembled frame in the center of the fabric (see Fig. 4).
6. Slide the Hook & Loop or Snaps along the frame until they are
evenly spaced.
7. Pull the edge of the screen fabric and wrap it around the frame
(see fig 5). Attach the screen fabric on all four (4) sides.
8. Carefully, turn the entire screen assmbly over and inspect.
Adjust the position of the sliding fabric attachments to remove
any wrinkles.
For Snap Fabric Attachment:
1-B. Insert sliding snap attachments into
all four (4) sections of the frame
(See Fig. 1-B).
For Larger sizes requiring Vertical support:
3. When assembling a large frame, use the two (2) vertical support
connectors on the top and bottom sections (see fig. 3). Connect
these sections together with the Vertical Support Bar.
Secure all frame sections and connectors with provided screws.
Insert Sliding
Hook & Loop
Attachment
Approx.
3”
Spacing
Inser
t
Sliding
Snaps
Profile Permanently Tensioned Projection Screen Page 2 of 4
Back of
Fabric
Back of Fabric
Back of Fabric
Wrap the fabric
around and attach to frame
Back of
Screen Fabric Assembled Frame
centered on
Screen Fabric
(Viewing Surface Down)
Figure
1 - A
Figure
1- B
Figure CFigure D
Figure E
Figure F
Profile Permanently Tensioned Projection Screen Page 3 of 4
Front of F
abric
Front of Fabric
Back of
Fabric
Back of
Fabric
Front of Fabric
Front of Fabric
Trim Frame Attachment
1. Snap the trim frame corners onto all four (4) corners.
Adjust the fabric if needed (See fig. 6).
2. Snap the trim frame sections onto all four (4) sides of the frame.
Adjust the fabric if needed (See fig. 7).
Figure G
Figure H
Mounting On the Wall
1. Mount the Wall Brackets in the desired location. They must be installed level and have at least 2 fasteners (by others) per bracket.
2. Lift the assembled screen up and over the wall brackets. The screen will align with the channel in the frame.
3. Carefully let the screen settle on the wall brackets.
Wall Mounting
Bracket
WALLWALL
WALL
WALL
WALL
WALL
Screen Frame
Side View
Screen Frame
Side View
Mounting
Hardware
(by Others)
Wall
Mounting
Bracket
Lift Screen
Up & Over
Wall Brackets
It will align
with the Channel
in the Frame
Screen Frame
Properly Installed
3 ¾”
* Please Note:
Mounting bracket fasteners must
be positioned at least 4 ½” below
the ceiling or overhead structure.
4 ½”*
Ceiling or Overhead
Obstruction
Ceiling or Overhead
Obstruction
Ceiling or Overhead
Obstruction
¾”
B C D
(765) 987-7999
www
.draperinc.com
Altri manuali Draper Schermo di proiezione
Draper
Draper Access Fit Series Manuale utente
Draper
Draper Artisan E Series Manuale utente
Draper
Draper Targa Manuale utente
Draper
Draper Salara Manuale utente
Draper
Draper FlexShade Manuale di programmazione
Draper
Draper Signature/Series V Manuale
Draper
Draper nocturne+ c Istruzioni per l'installazione
Draper
Draper Salara/Hardwire Manuale utente
Draper
Draper Access/Series M Manuale
Draper
Draper Access M Manuale utente
Draper
Draper Targa Manuale
Draper
Draper Premier XL 220 Manuale utente
Draper
Draper 220V Ultimate Access Manuale utente
Draper
Draper Acumen M XT1000E Manuale utente
Draper
Draper Piper Portable Screen Manuale utente
Draper
Draper Clarion Manuale utente
Draper
Draper E series Manuale utente
Draper
Draper Targa Manuale
Draper
Draper Access MultiView Manuale
Draper
Draper Signature Series E Manuale utente
