Draper VMS/KD Manuale utente
■STOCK No. 64600 ■PART No.VMS/KD
•INSTRUCTIONS•
03/2001
IMPORTANT: PLEASE READ THESE INSTRUCTIONS
THOROUGHLY BEFORE USE.
UNDERSTANDING HOW THIS MACHINE WORKS AND SETTING IT
CORRECTLY IS FUNDAMENTAL TO OBTAINING
A SATISFACTORY RESULT.
MITRE SAW
MITRE SAW TECHNICAL DATA
COMPONENT PARTS
1. Vice clamp assembly.
2. Length stop assembly.
3. Cut depth stop.
4. Cut depth stop screws.
5. Two plastic feet with screw holes
for bench mounting.
6. Base socket head screws.
7. Pre-set angle arm.
8. Pivot pin.
9. Plated cursor screw.
10. Cursor.
11. Blade tensioning nut.
12. Pivot screw.
13. Saw table.
14. Saw frame handle.
15. Saw frame guide bar carriers.
16. Saw blade.
17. Saw frame carriers.
18. Saw frame assembly.
Specification:
Max. cutting width clamped at 45°............110mm
Max. cutting width clamped at 90°............160mm
Max. cutting height ...................................120mm
Blade length..............................................550mm
Blade width.................................................45mm
Table length ..............................................400mm
Max. reach of adjustable stop...............
450mm
Weight......................................................3.1kg
PRE-SET ANGLES
ASSEMBLY OF ACCESSORIES
The vice clamp ✕✌ can be mounted on the left or right hand side of the saw table front
for holding workpieces securely.
The adjustable length stop ✖✌ can be mounted at either end of the saw table and set
for the required length of cut.
90˚
45˚ 36˚
30˚ 22.5˚
✕✌
✖✌
IMPORTANT WARNING
To get the best from your saw and ensure it is correctly set ensure the following is
correct:
(a) The saw blade is tensioned sufficiently to avoid ‘whip’ which will cause the blade to
deviate from a true cut.
(b) The blade is ‘in line’ and central to the frame.
(c) The workpiece is square and true to the base casting.
(d) Tension is always released after use.
(e) The correct type of blade for the application is used.
(f) After assembly and setting has been carefully carried out, always test your mitre
saw and the angles with some scrap timber to ensure the machine is assembled
correclty and cutting true.
SPARE BLADES
Spare blades are available for this Mitre Saw. Draper Stock No. 60506 ..............14tpi
60507 ..............18tpi
60508 ..............24tpi
DRAPER TOOLS LIMITED,
Hursley Road, Chandler's Ford, Eastleigh, Hants. SO53 1YF. U.K.
Helpline: (023) 8049 4344.
Sales Desk: (023) 8049 4333.
General Enquiries: (023) 8026 6355.
Fax: (023) 8026 0784.
http://www.draper.co.uk
e-mail: [email protected]
©Published by Draper Tools Ltd.
No part of this publication may be reproduced,
stored in a retrieval system or transmitted in
any form or by any means, electronic, mechanical
photocopying, recording or otherwise without prior
permission in writing from Draper Tools Ltd.
Indice
Altri manuali Draper Sega
Draper
Draper STORMFORCE BS200/250SF Manuale utente
Draper
Draper PT185A Manuale utente
Draper
Draper CSM355 Manuale utente
Draper
Draper CTS315A Manuale utente
Draper
Draper BS190 Manuale utente
Draper
Draper VMS/KD/2 Manuale utente
Draper
Draper MBS46A Manuale utente
Draper
Draper BTS255 Manuale utente
Draper
Draper SMS250A Manuale utente
Draper
Draper CS14A Manuale utente
Draper
Draper BS230B Manuale utente
Draper
Draper SMS210 Manuale utente
Draper
Draper ABSSG Aggiornamento firmware
Draper
Draper BTS205 Manuale utente
Draper
Draper PT187A Manuale utente
Draper
Draper CMS/600 Manuale utente
Draper
Draper 56791 Manuale utente
Draper
Draper BS250A Manuale utente
Draper
Draper BS200A Manuale utente
Draper
Draper RS12VD Manuale utente
