Drill Master MD1 Manuale utente
Operating Instructions
Grinding Machine
Machine Type: MD1
Date: 2017.2.15
Operation Instruction of Grinding Machine
Page 2 of 16
Table of Contents
1. Safety Instruction
2. Specification
3. Installation
4. Operation
5. Maintenance
DrillMasters Eldorado Tool, Inc.
Page 3 of 16
1 Safety Instruction
This operating instructions manual contains important prerequisite for safe and efficient working
with the machine. It should be kept readily accessible in the vicinity of the machine.
Before installation and commissioning, carefully read and observe the operating instructions.
The operating instructions manual does not contain any repair information. Repairs should only be carried
out by specialist personal of the competent customer service organization.
1.1 Safety Regulation
1.1.1 Intended Application
The DrillMasters Eldorado Tool grinding machine MD1 is designed for low volume production re-
sharpening of single flute gundrills.
1.1.2 General Potential Hazards with This Machine
The machine was developed, designed and built according to technical safety aspects. Usage contrary to
that intended or usage by unqualified personnel may result in danger.
-to life and health of the operator
-to the machine itself
-to other property of the operator
-to the performance of the machine
-and consequently to its economy
Insofar as permitted by the sequence of operations and the intended purpose of the machine, all danger
areas have been guarded so that with proper and careful handling there is no risk to body and life of the
operating personnel. During operation it is not necessary and therefore prohibited to tamper in the
working area or remove safety guards in order to be able to interfere with the operation,
The general danger potential in improper and careless use of the machine consists of:
· Mechanical danger through
- impact, due to the kinetic energy of the moving masses
- maiming and shearing
- grabbing and wrapping and drawing-in
- sharp edges and corners
- fluids under pressure
- freely movable parts
· Electrical danger through
- electrical contact (direct or indirect)
Operation Instruction of Grinding Machine
Page 4 of 16
· Combination of dangers through
- faulty assembly
- incorrect clamping of tools
- wheel wear
- failure and/or incorrect application of protective measures.
· Danger through emission
- The equivalent continuous sound pressure level of the grinding machines is less than 80
dB(A).
· Residual dangers, i.e. potential, not obvious danger through
-human error
-noise
-ejection of parts
-control system failure
-sharp tools in set-up work
-fire
-allergic reactions, mucous membrane irritation through dust or lubricants
-hot machine parts or tools
-injuries through rotating wheels
1.1.3 Requirements Imposed on the User/Operator
The operator must have the necessary technical qualifications to be able to operate the machine
-after instruction in how to operate it and
-reading the operating instructions.
It is of particular importance that he is able to recognize dangers resulting from the use of the machine.
The person in charge of the machine has the duty to make the operating instructions manual belonging to
the machine available to the machine operator. The person in charge of the machine is responsible for
working sure that the machine operator has attentively read and understood the operating instructions. The
operating instructions should be kept in the immediate vicinity of the machine.
The operator must use the machine only in a serviceable condition. All factors impairing mental
concentration of the operator should be eliminated from the outset, to ensure proper operation of the
machine.
The machine must only be operated by personal of whom proper use can be expected.
The person in charge of the machine must make sure that no unauthorized person uses the machine. The
operator is responsible for third persons the working area. The competencies for various activities on the
machine must be clearly defined.
Page 5 of 16
1.1.4 Personal Safety Equipment
- Wear appropriate protective clothing when working with the machine.
- Wear closely fitting clothing when operating the machine.
- Operators with long hair must wear a hair net.
- No protective gloves
- Wear safety goggles when operating the machine.
1.1.4 Safety during Repair and Maintenance
Before starting with maintenance and repair works, switch off main circuit breaker and lock to avoid
restoration of power.
- Maintenance and repairs must only be carried out by authorized specialists. In this context
special note should be taken of the dangers when working on electrical system.
- The relevant accident prevention and safety regulations as well as the information in the
machine documentation and the supplementary documentation must be observed.
- Immediately renew damaged or removed information and warning signs as well as safety
inscriptions.
- After completed repairs, correctly refit all removed guards. Unauthorized conversions or
changes to the machine impair the safety of operating personnel and of the machine,
therefore they are strictly forbidden.
- After completed maintenance and repair to grinding machine, units or fixtures, the final
customer shall be responsible for the attachment and the function of the guards and other
safety installations as part of the overall safety of the machine.
1.1.6 Safety during Tool Change and Set-up
Prior to every tool change and during set-up work on the machine, the main motor must be switched off.
1.1.7 Behavior in an Emergency
In emergency situations immediately
- press the red emergency-off switch or (if available)
- pull the emergency-stop line.
1.2 Warning Plate
Persons entrusted with transport, storage, operation or maintenance and repair of the machine must be
familiar with the contents of the operating instruction manual. These instruction, particularly the safety
instructions ,must be obeyed.
In addition to the operating instructions, observe the valid general, statutory and other
regulations for the prevention of accidents and for environmental protection which are in force in the
DrillMasters Eldorado Tool, Inc.
Operation Instruction of Grinding Machine
Page 6 of 16
particular country.
Some symbols used on the machine are explained below. Read the explanations of these symbols
carefully so that you are quite sure what they mean:
The caution symbol is a warning of the danger of fatal accidents or
injuries if the control and work instructions are not observed or not
observed exactly.
This symbol is a warning against dangerous electric voltage. Failure to
heed this safety direction in the operating instructions can result in
personal hazard. In parts of the machine which are marked with this
symbol repairs may only be carried out by trained maintenance and
repair personnel.
2 Specification
2.1 Technical Data
Grinding Machine MD01
Clamping Range Ф2.0~Ф32
Minimum flute length of tool 100.0mm
Power 0.55KW
Speed 2800r/min
Net Weight 70KG
Voltage
- working voltage 380V
- frequency 50HZ
DrillMasters Eldorado Tool, Inc.
Page 7 of 16
2.2 Machine Noise
The equivalent continuous sound pressure level of the grinding machine is less than 80 dB(A) .
2.3 Function of the machine
Machine base
- this is a found structure to accommodate the entire machine including the botton
box, the slide part and grinding fixture.
- precision-finished mounting surfaces
Slide Part
- constructed with linear guideways
- the profile guide beads are permanently bolted onto the machine
Grinding Fixture
- the grinding fixture is designed for low volume production re-sharpening of single flute
gundrills.
- The fixture may be installed on a DrillMasters Eldorado Tool grinding machine MD1, or a
standard tool grinding machine. The desired angles are on the grinding fixture using graduated
scales.
Grinding fixture PS
- the grinding fixture PS was developed for re-sharpening single flute gundrill within a diameter
range from 0.5~6.0mm.
- The fixture may be installed on a DrillMasters Eldorado Tool grinding machine MD1 or a
standard tool grinding machine.
2.4 Legend of the Machine
1. machine base
2. slide part
3. grinding fixture
4. grinding fixture PS
3. Installation
3.1 Transport
CAUTION:
Incorrect handling when installing and transporting the machine can cause serious injuries. Observe
safety regulations during unloading. Presence or working under suspended loads is strictly forbidden.
3.2 Installation
3.2.1 Setting-up and alignment of the machine
Operation Instruction of Grinding Machine
Page 8 of 16
The installation and alignment of the machine must be carried out by authorized specialist
personnel.
- the permanent stability of the machine must be assured
- the surface on which the machine is installed must carry the unloaden weight of the machine.
3.2.2 Electrical connection
The mains input connection is located in the switch cabinet.
Check the input terminals for correct designation of the voltage before commissioning the
plant. The actual value of the mains supply voltage must corresponds to the nominal voltage rating of the
plant. The main circuit breaker and the motor-protection circuit breakers must be closed before connecting
the feed cable to the mains supply.
CAUTION: dangerous voltage
·Always keep the switch cabinet locked
· Access for maintenance and repair tasks is granted only to authorized personnel subject to
compliance with the applicable safety precautions.
· Observe the instructions of the local electric supply company with regard to the maximum
power rating of the mains supply.
· The sense of rotation must be checked for all motors, is a “clock-wise rotating field”
present?
The direction of rotation can be reversed by interchanging two mains phase lines.
3.2.3 Preparation for the start-up of the machine
Mechanical inspection
A general inspection has to be carried out concerning the functional safety of the complete
machine, of all mechanical components, as well as of all the protection devices.
Wheel inspection
- Cup wheel
For re-sharpening single flute gundrills within a diameter range from 0.5 to 2.0mm a cup
wheel is most suitable. The gait of the wheel is chosen to keep an excellent grinding
quality and sufficient stock removal without overheating the tool.
- Double grinding wheel
The double grinding wheel is ideal for re-sharpening single flute gundrills up to 45mm
diameter. The coarse grit of the outer wheel is for roughing the tool with high stock
removal and minimum heating of the tool. The fine grit of the inner grinding wheel
provides optimum
Electrical inspection
The proper electrical assembly must be checked according to the regulations of the customer
and local authorities. Check the setting of the protection devices, directions of rotation of the
Page 9 of 16
electric motors and electrical connections.
Start-up of the machine
After the completion of all inspections is ready for operation. All machine functions are
now checked in manual operation by trained and qualified personal. After completion of
this work the test run of the machine can be started.
4 Operation
4.1 Start
Before start please make sure that the machine voltage is right, and then open the electric tank, push
the button make the machine start.
4.2 Operating with the grinding fixture
The gundrill is inserted into the clamping unit and a vee-shaped jaw holds the gundrill securely in the
flute.
Considering the use of the gundrills, please chose the right angle following the pig 4.1 and pig 4.2.
DrillMasters Eldorado Tool, Inc.
Operation Instruction of Grinding Machine
Page 10 of 16
Table 4.1
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Drill Master Macinacaffè
