Drive 14001E Manuale utente

REV6.12.11.14

User Manual

Alternating Pressure Pump and Pad System

Item # 14001E, 14001EFD & 14002E

REV6.12.11.14

IMPORTANT SAFEGUARDS

When using electrical products, especially when children are present, basic safety precautions

should always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING

DANGER

To reduce the risk of electrocution:

Always unplug this product immediately after use.

Do not use while bathing.

Do not place or store product where it can fall or be pulled into a tub or sink.

Do not place in or drop into water or other liquids.

Do not reach for a product that has fallen into water. Unplug immediately.

WARNING

To reduce the risk of burns, electrocution, fire, or injury to persons:

A product should never be left unattended when plugged in.

Close supervision is necessary when this product is used by, on, or near children or

physically challenged individuals.

Use this product only for its intended use as described in this manual.

Do not use attachments not recommended by the manufacturer.

Never operate this product if it has a damaged cord or plug, if it is not working properly, if it

has been dropped or damaged, or dropped into water. Return the product to a service

center for examination and repair.

Keep the cord away from heated surfaces.

Never block the air openings of the product or place it on a soft surface, such as a bed or

couch, where the air openings may be blocked. Keep the air openings free of lint, hair, and

the like.

Never drop or insert any object into any opening or hose.

DO NOT use this product in or near explosive atmospheres, or where aerosol (spray)

products are being used.

DO NOT pump combustible liquids or vapors with the product or use in or near an area

where flammable or explosive liquids of vapors may exist.

DO NOT operate this product in an oxygen enriched environment, i.e. oxygen tent or

oxygen hood.

Use only in well ventilated areas.

Connect this product to a properly grounded outlet only. See Grounding Instructions.

REV6.12.11.14

Introduction

This manual should be used for the initial set up of the system and for reference purposes.

General

The Med Aire series is a high quality and affordable air support surface system suitable for

pressure ulcer prevention and treatment. It has been specifically designed for prevention and

treatment of pressure ulcers and offers an effective solution to 24-hour pressure area care.

The Med Aire series has been tested and certified to the following standards:

UL 1431

EN 60601-1

EN 60601-1-2

Intended Use

The Med Aire series is intended to reduce the incidence of pressure ulcers while optimizing

patient comfort. It also is appropriate for the following:

Individual home care setting and long-term care facilities

Pain management as prescribed by a physician.

Contraindication

Patient conditions for which the application of pressure relieving therapy on an alternation

system is contraindicated are as follows:

Cervical or skeletal traction

Unstable spinal cord injuries

Product Description

Pump

Power Switch (1) The switch is on the front faceplate of the pump.

Turn ON the power, the pump will start operation.

Pressure-adjust Knob (2) Turn the soft/firm knob to set a comfortable pressure

level. (Model 14001E only)

Bubble Pad Lay it on top of a base mattress. Please refer to the Specifications section

for details.

Manual

Always read this manual before using this product.

REV6.12.11.14

Installation

Step 1 Place the bubble pad flat on a base mattress, which should be on a bed frame.

The inflation tubes should be towards the foot end so that they can be connected to

the inflation nozzles on the pump.

Step 2 Cover with a cotton sheet to avoid direct skin contact and reduce friction.

Step 3 Hang the pump over the frame or board at the foot end of the bed.

Make sure the pump is secured.

Step 4 Connect the inflation tubes from the bubble pad to the pump’s inflating nozzles.

Make sure they are properly attached.

CAUTION:Make sure the inflation tubes are not kinked or tucked under the pad.

Step 5 Plug the power cord into an electrical outlet with grounded AC power.

If the power cord has a grounding wire with a grounding pin, then this three-wire plug

must be plugged properly into an outlet and grounded as shown in the figure in the

Grounding Instructions section.

NOTE:Before inserting the plug into the outlet, make sure the voltage is compatible.

CAUTION:Make sure this product is well grounded.

Step 6 Turn on the power by pressing the power switch at the right side of the pump.

Proceed to the Operation section.

Step 7 Make sure to disconnect the pump by unplugging the power cord when it is not in

use.

REV6.12.11.14

Grounding Instructions

This product should be grounded when it is equipped with a cord that contains a grounding

wire with a grounding plug. In the event of an electrical short circuit, grounding reduces the risk

of electric shock by providing an escape wire for the electric current.

DANGER

–

Improper use of the grounding plug can result in a risk of electric shock.

If repair or replacement of the cord or plug is necessary, do not connect the grounding to either

flat blade terminal. The wire with insulation having an outer surface that is green with or without

yellow stripe is the grounding wire.

Check with a qualified electrician or serviceman if the grounding instructions are not

completely understood, or if in doubt as to whether the product is properly grounded.

If it is necessary to use an extension cord, use only a 3-wire extension cord that has a

three-prong grounding plug and a 3-slot receptacle that will accept the plug on the product.

Replace or repair if damaged.

Polarized Plug

–If the product is provided with a 2-wire polarized attachment plug

This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of

electric shock, this plug is intended to fit into a polarized outlet only one way.

If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact

qualified electrician. Do not attempt to modify the plug in any way.

REV6.12.11.14

Operation step by step

Always read the operating instructions before use.

14006E

Step 1 Turn on the power. The indicator of the power switch will come on.

The pump starts to pump air into the bubble pad.

14005E

Step 1 Same as above.

Step 2 For time-saving in the first inflation, turn the pressure knob to the full Firm position.

NOTE:It requires approximately 10 minutes for a bubble pad to be fully inflated.

Step 3 Turn the pressure-adjust knob to set a comfortable pressure level from soft to firm

according to patient’s weight and comfort.

Pressure set up

It is recommended that the pressure-adjust knob being turned to Firm when the bubble pad is

initially inflated. Users can then easily adjust the pressure level of the bubble pad to a desired

firmness by themselves or according to the suggestion from a health care professional.

If the pressure is consistently low, check for any leakage occurring in inflation tubes. Contact

your local dealer for replacement of any damaged tubes.

Troubleshooting

Problems

Solutions

The pump doesn’t work

1. Check if the plug is inserted firmly into the outlet.

2. Turn on the power switch again.

If the power indicator is ON and the pump still doesn’t work,

contact your local dealer immediately.

If the power indicator is OFF, there may be a faulty outlet. Try to

connect the power cord to another outlet. If the power indicator

is still OFF, contact a qualified electrician for main power check.

Incomplete inflation

(Low pressure)

1. For a quick check, adjust the pressure to Firm.

2. Check to see if the inflation tubes connected to the pump are

twisted or disconnected, or any leakage occurring.

Always keep the tubes straight.

Change the tubes if there is any leakage.

REV6.12.11.14

Cleaning

In this section, we describe the procedures to clean and decontaminate the pump and bubble

pad. It is important to follow these procedures before using the system on patients.

The cleaning task is required at least once a week to maintain personal hygiene.

Pump

DO NOT immerse or soak the pump.

Check for external damage and move the pump to a cleaning area.

Place the pump on a work surface and spray or wipe the outside of the case with

quaternary ammonium solution.

DO NOT spray any cleaning solution directly on the surface of the pump.

DO NOT use a Hypocarbonate or Phenolic based cleaning solution as this may cause

damage to the case. Allow the solution to incubate for 10 minutes or accordingly as

stated by the cleaning product used.

Spray cloth with cleaning solution and clean faceplate. DO NOT allow excess cleaning

solution on faceplate or control panel. (If solution gets inside, damage will occur.)

Allow surface to thoroughly dry after cleaning.

After the pump is thoroughly cleaned and dried, proceed to plug in the pump and test to

see if it runs normally.

Bubble Pad

Any obvious blood spots should be cleaned thoroughly with 1:9 Hypochlorite solution

(1 part bleach to 9 parts water) and allow drying for at least 10 minutes. Then blot with

a clean, damp cloth.

Brush or wipe down all surfaces with soap and water before applying any liquid.

Allow it to thoroughly air dry. Once the inside is dry, turn it back: wipe down the outside

of the bag with disinfectant.

Dry the bubble pad away from direct sunlight after cleaning.

Handling And Storage

Lay the bubble pad flat. Fold or roll it carefully.

Unplug the pump and store with proper identification tag.

Follow the national requirement to dispose the pump.

Maintenance

Check the power cord and plug to see if there are abrasions or excessive wear.

Plug in the pump and check the airflow from the hose connection port. The airflow

should alternate between ports every half-cycle time.

REV6.12.11.14

Specifications

Pump

Specification

Power Supply

110V/60Hz

Air output:

>4 liter/min.

Pressure range

14001E: 45 mmHg –110 mmHg

14002E: 100 mmHg

Cycle time

12 min.

Power consumption

Fuse

Size

8.8” x 4.2” x 4”

Weight

3.1 lbs.

Mattress

Specification

Size

78” x 35.4” x 2.5” Inflated

Cells

130 bubble cells

Material

PVC (EN-71, low toxic)

Color

Beige

Warranty

Your Drive brand product is warranted to be free of defects in materials and workmanship for

one year of the original consumer purchaser for the pump and 90 days for the pad.

This device was built to exacting standards and carefully inspected prior to shipment. This 1

Year Limited Warranty is an expression of our confidence in the materials and workmanship of

our products and our assurance to the consumer of years of dependable service.

This warranty does not cover device failure due to owner misuse or negligence, or normal

wear and tear. The warranty does not extend to non-durable components, such as rubber

accessories, casters, and grips, which are subject to normal wear and need periodic

replacement.

If you have a question about your Drive device or this warranty, please contact an authorized

Drive dealer.

REV6.12.11.14

Manual del usuario

Bomba de presión alterna y Sistema de colchoncillo

Artículo # 14001E & 14002E

Questo manuale è adatto per i seguenti modelli

Indice

Lingue:

Altri manuali Drive Pompa dell'acqua

Drive

Drive Heavy Duty Suction Device Manuale utente

Manuali Pompa dell'acqua popolari di altre marche

Neptun

Neptun NPHW 5500 Manuale utente

Sensidyne

Sensidyne Gilian BDX-II Istruzioni per l'installazione e il funzionamento

Draper

Draper 47808 Manuale utente

Trolla

Trolla 12820 Manuale utente

Sunfab

Sunfab SVH Series Manuale utente

WilTec

WilTec 50740 Manuale utente

Fieldmann

Fieldmann FVC 5015 EK Manuale utente

Everbilt

Everbilt EFSUB5-122HD Manuale utente

Graco

Graco Husky 3300e Manuale utente

esotec

esotec 101018 Manuale utente

moyno

moyno 2000 CC Manuale utente

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manuale utente

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guida alla risoluzione dei problemi

DUROMAX

DUROMAX XP WX Series Manuale utente

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manuale utente

Franklin Electric

Franklin Electric IPS Manuale utente

Xylem

Xylem e-1532 Series Manuale utente

Milton Roy

Milton Roy PRIMEROYAL Manuale utente