DSC SEA-B-QUE Manuale utente

○

1○

2○

3○

4○

5○

6○

7○

8○

9○

1. DC+12V IN: Power input DC+12V/1.5A.

2. DC+12V OUT: DC+12V/750mA for camera only, and with an over current protector.

(Note: If you don’t use this port for cameras, you can use the DC+12V/500mA adaptor.)

3. ALARM IN: Once triggered, the built-in buzzer rings on for a 20-sec time. This port could be connected to

alarm sensor, e.g.: PIR Detector, Magnetic Reed Switch Detector.

4. AUDIO IN: RCA female for input audio signal.

5. VIDEO IN: BNC female for input video signal.

6. POWER/State LED: Indicated to power on and ARM status.

7. DISARM: Alarm ON / OFF selection.

8. CH SELECT (A B C D): 5.8GHz transmission channel selection.

9. ID AND ALARM MUTE: ID address setting is use for paring with receivers (RX unit). It must be make the

same code setting to link transmitter and receiver each other. The alarm mute function is use for muting built

-in buzzer at TX unit.

10. ANT: RP-SMA connector for connected to 5.8 GHz antenna.

*REMARK: When the frequency channels have the interference, adjust antenna or change the channel of transmitter

and don’t close to 802.11 a/b/g AP router and other 5.8GHz devices. (Note: Please keep 3 ~ 5 meter away)

* Panel View: TX unit

Bit 1 Bit 2 Bit 3 ID Address

(Pairing with RX)

Bit 4 Alarm Mute

00000ON

00111OFF

0102

0113

1004

1015

1106

1117

(1 = SW ON, 0 = SW OFF)

11/5/2009

Indications Power/State LED

Power On On

ARM High speed Flashing

MODEL:DSC-5800VHK( :SK2-5800A)

○

1○

2○

3○

4○

5○

6○

7○

8○

1. DC+12V IN: Power input DC+12V/500mA.

2. ALARM OUT: Once triggered, the built-in buzzer and alarm remains on for a 20-sec time. This port could

be connected to alarm devices, e.g.: Siren, Flashing Unit.

3. AUDIO OUT: RCA female for audio signal output.

4. VIDEO OUT: BNC female for video signal output.

5. POWER/STATE LED: Indicated to power on or ARM and RF link status.

6. DISARM: Alarm ON / OFF selection.

7. CH SELECT (A B C D): 5.8GHz transmission channel selection.

8. ID AND ALARM MUTE: ID address setting is use for paring with transmitters (TX unit).

It must be make the same code setting to link transmitter and receiver each other. The alarm mute function

is use for muting built-in buzzer and disables the alarm output at RX unit.

9. ANT: RP-SMA connector for connected to 5.8 GHz antenna and built-in 3.3V / 25mA bias-tee circuit for an

active antenna.

*REMARK: When the frequency channels have the interference, adjust antenna or change the channel of transmitter

and don’t close to 802.11 a/b/g AP router and other 5.8GHz devices. (Note: Please keep 3 ~ 5 meter away)

* Panel View: RX unit

Bit 1 Bit 2 Bit 3 ID Address

(Pairing with TX)

Bit 4 Alarm Mute

00000ON

00111OFF

0102

0113

1004

1015

1106

1117

(1 = SW ON, 0 = SW OFF)

11/5/2009

Indications Power/State LED

Power On On

ARM High speed Flashing

RF Loss/Waiting TX Link Low speed Flashing

MODEL:DSC-5800VHK( :SK2-5800A)

5.8GH TX (Transmitter) ×1 5.8GH RX (Receivers) x1

Antenna ×2 User manual ×1

Screws x 4 ×2 Plastic-Conical-Anchor x 4 ×2

Power Adaptor (DC 12V/1.5A) ×1 Power Adaptor (DC 12V/500mA) x1

* Packing List:

Model No. TX RX

CHANNAL CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8

FREQUENCY 5740

MHz

5752

MHz

5771

MHz

5790

MHz

5809

MHz

5828

MHz

5847

MHz

5760

MHz

RF IMPEDANCE 50 ΩTypical

5.8G BIAS-TEE 3.3V/25mA

MINIMUM RECEIVER SENSITIVITY -84dBm

POWER SUPPLY DC12V/1.5A Adaptor DC12V/500mA Adaptor

CURRENT CONSUMPTION 350mA 280mA Max.

DC OUTPUT DC12V/750mA

RF OUTPUT POWER 500mW

VIDE INPUT / VIDEO OUTPUT 1.0 Vp-p Composite @ 75Ω

AUDIO INPUT / VIDEO OUTPUT 2.0 Vp-p Typical, 3.0 Vp-p Max. @ 600Ω

ALARM INPUT TTL/CMOS (Level Detection)

ALARM OUTPUT NC/NO/COM (Dry Contact) Contact

Rating: AC 125V / 0.5A ; DC 24V / 1A

OPERATION TEMPERATURE 14° F ~ 122° F (-10°C ~ 50°C)

WEIGHT 5.8 Oz ( 164 g)

DIMENSIONS W x H x D: 110 x 30 x 88 mm (without Antenna)

* Specification :

11/5/2009

*** All Specifications are subject to change without notice.

1. Be careful, never let any water in this equipment.

2. If necessary, use a soft cloth moistened with alcohol to wipe off the dust.

3. Be extra careful not to shake the unit.

4. Avoid places where temperatures exceed 122° F (50°C)or higher.

5. Avoid places where there are frequent vibrations or shocks.

6. When any abnormalities occur, make sure to unplug the unit and contact your local dealer.

* Caution for Installation:

MODEL:DSC-5800VHK( :SK2-5800A)

FCC Part 15 Notice:

This equipment has been tested and found to comply with the limits for a Class B digital device, pur-

suant to part 15 of the FCC rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates uses and can ra-

diate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interfer-

ence will not occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

-Consult the dealer or an experienced radio/TV technician for help.

1. This Transmitter must not be co-located or operating in conjunction with any other antenna or

transmitter.

2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with a minimum distance of 20

centimeters between the radiator and your body.

3. Any changes or modifications (including the antennas) made to this device that are not ex-

pressly approved by the manufacturer may void the user’s authority to operate the equip-

ment.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali DSC Sistema di sicurezza

Manuali Sistema di sicurezza popolari di altre marche

Inner Range

Inner Range Concept 2000 Manuale utente

Climax

Climax Mobile Lite R32 Istruzioni per il montaggio

CADDX

CADDX NX-6 Manuale utente

FBII

FBII XL-31 Series Manuale utente

Johnson Controls

Johnson Controls PENN Connected PC10 Manuale utente

Aeotec

Aeotec Siren Gen5 Manuale utente

Blaupunkt

Blaupunkt SA 2700 Manuale utente

IDEAL

IDEAL Accenta Manuale del proprietario

AJAX

AJAX DoubleButton Manuale utente

Swann

Swann SW-P-MC2 Manuale utente

Ecolink

Ecolink Siren+Chime Manuale utente

Digital Monitoring Products

Digital Monitoring Products XR150 Manuale utente

EDM

EDM Solution 6+6 Wireless-AE Manuale utente

Highway Safety Group

Highway Safety Group EA401 Manuale utente

Siren

Siren LED GSM Manuale utente

Detection Systems

Detection Systems 7090i Istruzioni per il montaggio

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuale utente

Siemens

Siemens FDM273 Manuale utente