Duplo 486P Manuale utente
1
486P Paper Cutter
Operation Manual
2
Revison History
Date Changes Reason Page Technical Bulletin
From To
3
Index
1. Safety Rules…………………………………………………………………………………………………………………………4
2. Specifications………………………………………………………………………………………………………………………7
3. Name Plate………………………………………………………………………………………………………………………….7
4. Accessories………………………………………………………………………………………………………………………….8
5. Key Components………………………………………………………………………………………………………………….9
6. Control Panel and Function Keys………………………………………………………………………………………..10
7. Power On……………………………………………………………………………………………………………………………11
8. Cutting Procedure………………………………………………………………………………………………………………12
8.1 Manual Cut…………………………………………………………………………………………………………………..12
8.2 Repeating Cut……………………………………………………………………………………………………………….12
8.3 Push-Out After Cut……………………………………………………………………………………………………….12
8.4 Define a Job.…………………………………………………………………………………………………………………13
8.5 Select a Defined Job……………………………………………………………………………………………………..13
8.6 Check Cutting Factor on A Job………………………………………………………………………………………14
8.7 Editing an Existing Job…………………………………………………………………………………………………..14
9. Trouble Shooting Guide………………………………………………………………………………………………………15
10. Adjustment
10.1 Cutting Blade Level Adjustment.……………………………………………………………………………….16
10.2 Cutting Depth Adjustment…………………………………………………………………………………………16
11. Cutting Blade Replacement…………………………………………………………………………………………….….17
12. Cutting Stick Replacement…………………………………………………………………………………………………18
4
1. SAFETY RULES
The machine has many safety features which make it a safe to operate. Regardless of your
experience, safety instructions must be read carefully, completely understood, and
applied to your daily work habits. If you do not understand or are confused by certain
safety instructions presented in this manual, discuss them with your supervisor. Machine
setup, cleanup, and maintenance operation will vary. Therefore, it is essential all
employees to practice safe work habits. SAFE WORK HABITS PREVENT INJURIES. The
main rule to follow is to ALWAYS make sure the main drive is STOPPED and LOCKEDOUT
when performing setup, cleanup, adjustment and maintenance operations.
The safety precautions in this manual provide guidelines for the protection and for that of
fellow workers.
1.1 Precautions
Before any maintenance is performed on the machine, switch off all sources of
electrical; do not operate the equipment when panels and safety covers are not in
place. Failure to observe this warning could result in personal injury.
1.2 Avoid Accidents
Most accidents are caused by the failure of some individual to follow simple and
fundamental safety rules and precautions. For this reason, most accidents can be
prevented by recognizing the real cause and doing something about it before the
accident occurs. With any machinery, a careful and trained operator is the best
insurance against an accident.
1.3 Safety Issues & General Safety Rules
DO
DO NOT
1. Read and understand this manual
before attempting to operate or
service the machine.
1. Do not attempt to operate or service the
machine without reading and understanding
this manual.
2. Be familiar with the machine safety
rules and practices.
2. Do not remove the safety devices.
3. Warn others of an intended action that
may endanger them.
3. Do not clean or lubricate moving parts of a
machine that is running.
4. Perform lubrication and oiling of the
machine only when power is off.
4. Do not unauthorized persons to operate the
machinery.
5. Verify that all guards are installed
before operating the machine.
5. Do not place tools on a machine that is
running.
6. When working on electrical
6. Do not reach into the machine to make
5
equipment, power must be shut off to
all circuits before any work is
attempted. Individual switches must
be opened and the equipment circuits
tested to make sure there is no power.
adjustments while it is running.
7. Be sure all operators are aware of all
areas and operations that require
extra safety measures.
7. Do not allow horseplay in the work area
6
1.4 AC Supply
1.4.1 Voltage steady state voltage: 0.9 to 1.1 of nominal voltage.
1.4.2 Frequency 099 to 1.01 of nominal frequency continuously; 0.98 to 1.02 for
short time.
1.4.3 Harmonics distortion not exceeding 10% of the total r.m.s. voltage between live
conductors for the sum of the 2nd through to the 5th harmonic.
1.4.4 Voltage Interruption Supply interrupted or at zero voltage for not more than 3ms at any
random time in the supply cycle with more than 1 s between successive interruptions.
1.4.5 Voltage dips not exceeding 20% of the peak voltage of the supply for more than one
cycle with more than 1 s between successive dips.
1.5 General Physical Environments
1.5.1 The minimum requirement for all electrical equipment is correct operation between air
temperature of +5
ﾟ
C and +35
ﾟ
C.
1.5.2 Electrical equipment is capable of operating correctly when the relative humidity does
not exceeding 50% at a maximum temperature of +45
ﾟ
C.
1.5.3 Electrical equipment is capable of operating correctly at altitude up to 1000m.
1.5.4 Electrical equipment is designed to withstand to protect against the effects of
transportation, and storage temperature within a range of -25
ﾟ
C to +55
ﾟ
C and for short
periods not exceeding 24 hours at up to +70
ﾟ
C.
1.5.5 Avoid exposing to vibration environment.
1.5.6 Avoid exposing to direct sunlight or heat rays.
1.5.7 Have to connect to the factory grounding system correctly.
1.5.8 Away from electric magnetic interference source sites, such welding, discharge machine.
7
2. Specifications
Specification DocuCutter 486P
Cutting Width
19.1”
Cutting Height 3”
Narrow Cut
1”
Power Supply 220VAC, 50/60Hz, 20A
Dimensions (D x W x H)
37.8” x 30.7” x 49.60”
Weight 280Kgs
Note: A dedicated AC power line is required.
3.Name Plate
8
4. Accessaries
4.1 Knife Replacement Tool
4.2 Tool Set
4.3 Registration Block
4.4 Operation and Service Manual
4.6 Cutting Stick x 2 821-483-220A
9
5. Key Components
Power
Switch
Key Pad
Manual
Switch
Key Switch
2-Hand Switch
2-Hand Switch
Safety
Beam
Blade
Side Table
10
6. Control Panel and Function Keys
Function Key Function
Backward/Program Setting
Forward
Stop
Start/Run
Clear the figure on display
Program
Repeating Cut
Metric (cm) and Standard Selection
Ejection Mode Setting
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Duplo Taglierina per carta
