DV8 Gladiator RBGL-03 Manuale utente
RBGL-03
Gladiator Rear Bumper with Drawer
2
1. Begin by opening your new bumper and inspecting all items for damage or missing items.
2. Remove factory bumper and tie up wiring for license plate lights and sensors if applicable.
3. Using Mopar provided tools, drop spare tire and remove tire.
4. Using a cut off wheel, trim off license plate/ bumper support bracket at red dashed line.
5. Next, remove heat shield and bracket that holds spare tire pulley.
3
6. Begin by installing the rear bracket. Note the orientation in the image. Using factory hardware, loosely secure
this to cross member as shown.
7. Install forward side brackets using the M12x30mm bolts and associated nuts and washers. (NOTE: Keep
all hardware loose to allow for adjustment when drawer is installed)
4
8. Place brackets with rails onto each forward bracket as shown. Use the image for orientation of each
bracket. When placing bolts into these brackets, feed the bolt from the top as shown in the image
below with the M12x30mm bolts. This makes tightening them during adjustment much easier.
5
9. Loosely attach the rear bracket to rail brackets with the same hardware on both sides.
10. Reverse the rubber bumpstops to face towards the rear of the vehicle. They are faced on the wrong
side for packing reasons. This is what the rear should look like prior to installing the bumper.
6
11. With help, loosely mount the rear bumper using the supplied M12x40mm bolts. Center the bumper
and tighten. (NOTE: use the side of the bumper and the gap between the sides to help with centering
the bumper.)
12. Pull the slide rails out, and with help, line up the drawer and push in. This may be tight, however do
not force the drawer. Also take note that the drawer will most likely hit the bumper. This is normal and
will be adjusted in the next steps. Do not damage the coating on the drawer or bumper, but the drawer
does need to be closed for the next steps.
7
13. Once drawer is closed. Move to the back and tighten these three bolts on each side.
14. Place a pry bar or large flat head screwdriver between front of drawer and hitch on the underside and
lift. Do this until there is 1/8”-1/4” gap between drawer and footstep of bumper.
8
15. Starting with the forward side brackets, tighten all hardware. Then work you way back down each side
rail bracket until secure. Green arrows then red.
16. Using the provided long nut plate, insert plate with nut upward into frame in hole shown. Using
provided hardware, tighten bolt.
9
17. Next close drawer and check handle adjustment. If the handle is not latching adjust handle so drawer
latches properly by moving the handle up.
18. Once drawer is working properly, install the provided flip down license plate kit. The flip down will pull
down from the top.
10
19. Using the two tapered Allen head bolts, install the trail plug. The bottom lip should be facing out to the
back of the vehicle as shown below.
20. Lastly, using the remaining supplied hardware, install the skid plate to the bottom of the drawer. The
remaining long volts will go in the back-rear holes with the shorter around the sides.
If you have any questions or concerns, please call us at 951-680-9595 or
email us at info@dv8offroad.com
Altri manuali DV8 Accessori per automobili
DV8
DV8 Inner Fender Guida alla configurazione
DV8
DV8 OE Plus Series Manuale utente
DV8
DV8 FBJL-02 Manuale utente
DV8
DV8 FS-15 Series Manuale utente
DV8
DV8 FBBR-04 Manuale utente
DV8
DV8 TC-6 Manuale
DV8
DV8 LPBR-02 Manuale utente
DV8
DV8 SPJL-10 Manuale utente
DV8
DV8 LBUN-01 Manuale utente
DV8
DV8 MPBR-01 Manuale utente
