DX Engineering DXE-MBVE-5AE-RT Manuale utente

Remote Tuner Option

for the

DXE-MBVE-5A

Vertical Antenna

DXE-MBVE-5UGRT8

for the

MFJ-998RT 1500 Watt Remote Tuner

DXE-MBVE-5UGRT8- INS-Revision 0b

Remote Tuner shown with additional optional parts

1200 Southeast Ave. - Tallmadge, OH 44278 USA

Phone: (800) 777-0703 ∙ Tech Support and International: (330) 572-3200

Fax: (330) 572-3279 ∙ E-mail: [email protected]

- 1 -

Introduction

This instruction manual describes the optional remote tuner upgrade package available for the

DXE-MBVE-5A multi-band vertical antenna system using the MFJ-998RT 1500 watt remote tuner.

There are two complete DXE-MBVE-5A systems for use with the MFJ-998RT Remote Tuner

DX Engineering

MBVE-5A

Model Numbers

MFJ-998RT

Brackets

MFJ-998RT

Tuner

1500 Watt

DXE-MBVE-5AE-RT

DXE-MBVE-5AERT8

X = Included

There are two upgrade retrofit kits for existing DXE-MBVE-5/5A systems for use with the MFJ-

998RT remote tuner. One with the tuner, one for use if the customer already has the tuner.

Upgrade kits include new longer base tube, brackets, remote tuner as selected below.

DX Engineering

Upgrade Model

Numbers

DXE-MBVE-

TBHW

Hardware Kit

DXE-MBVE-5A-

UGHW

Hardware Kit

MFJ-998RT -

Brackets

MFJ-998RT -

Tuner

1500 Watt

DXE-MBVE-5UG-RT

DXE-MBVE-5UGRT8

X = Included

There are also options available for other MFJ remote tuners allowing operation at 200, 300, 600 or

1500 Watt power levels. See the DX Engineering web site for complete details.

A complete manual including the assembly of the DXE-MBVE-5A antenna system that also

includes the information in this manual is available from DX Engineering and can be downloaded

from the DX Engineering web site at www.DXEngineering.com

Additional Material Needed but not Supplied:

JTL-12555 Jet-Lube™SS-30 Pure Copper Anti-Seize 12555 - To ensure good electrical

and RF connection for Aluminum Element Sections and also used on the threads of Stainless

Steel Hardware to prevent galling (seizing) and aid in proper tightening.

The assemblies or upgrades that use the extended base tube and new base tube insulator are

basically built the same as the standard DXE-MBVE-5A which is described in greater detail in the

DXE-MBVE-5A manual which is available on-line from the DX Engineering web site at

www.DXEngineering.com. The Saf-T-Tilt™ base and the aluminum vertical elements are all the

same for all of the DXE-MBVE-5A models. The only difference is the base tube length (Short Base

tube is 14”, Long Base Tube required for the remote tuners is 36”) new base tube insulator and

associated hardware.

- 2 -

Upgrade Hardware for the

Extended Base Tube Drawing

This drawing shows

the Upgrade

Hardware Kit that

includes the associated

hardware.

For existing systems,

the new hardware is

supplied with the

upgrade kits to make

installation easier.

NOTE: The Upgrade

Kits also include an

extended (36”) Base

Tube and a new

Drilled Insulator

SAF-T-Tilt™ Base Assembly Upgrade Hardware Kit

DXE-MBVE-5A-UGHW for the extended base tube option

Qty

Drawing

Ref.

Number

1/4”-20 x 3/4” long Hex Head Bolt, Stainless Steel

1/4”-20 x 2-3/4” long Hex Head Cap Screw, Stainless Steel

1/4”-20 x 3-1/4” long Hex Head Cap Screw, Stainless Steel

1/4” Flat Washer, Stainless Steel

1/4” Split Lock Washer, Stainless Steel

1/4" External Tooth Washer, Stainless Steel

1/4”-20 Hex Nut, Stainless Steel

1/4”-20 x 3” long Hex Head Cap Screw, Stainless Steel

1/2”-13 Hex Nut, Stainless Steel

1/2”-13 x 4-1/2” long, Hex Head Bolt, Stainless Steel

1/2” Flat Washer, Stainless Steel, Thick

1/2” External Tooth Washer, Stainless Steel

1/2” Split Lock Washer, Stainless Steel

1/2”-13 Flanged Nut, Stainless Steel

7” Wire, 14 ga PVC insulated, two 1/4” Ring Terminals

- 3 -

DXE-MBVE-TBHW

DXE-MBVE-TBHW Mounting Hardware Kit

For the MFJ-998RT Tuner mounting option

Qty

V-Block Saddle, Aluminum

U-Bolt, Stainless Steel, 3.75” x 5/16”-18

Tuner Shelf Bracket, Stainless Steel

5/16” Washer, Split Lock, Stainless Steel

5/16” Washer, Flat, Stainless Steel

5/16” Washer, External Tooth, Stainless Steel

5/16” Hex Nut, Stainless Steel,

2.25” Element Clamp with Threaded Stud, Stainless Steel

10-24 Hex Nut, Stainless Steel

1/4”-20 x 3/4” long Hex Bolt, Stainless Steel

1/4”-20 Hex Nut, Stainless Steel

1/4”-20 Acorn Hex Nut, Stainless Steel

1/4” Washer, External Tooth, Stainless Steel

#10 Washer, Split Lock, Stainless Steel, Thick

#10 Washer, Flat, Stainless Steel, Thick

#10 Washer, External Tooth, Stainless Steel

10” Wire Assembly, 12 ga, Black Insulated, two #10 ring terminals

Installing the MFJ-998RT option

The MFJ-998RT Tuner is mounted on a custom made stainless steel shelf that is attached to the

DXE-MBVE-5A antenna.

1. Install the four 1/4”-20 x 3/4” long Hex Head Cap Bolts, four 1/4” External Tooth Washers and

four 1/4”-20 Hex Nuts on the tuner shelf bracket as shown. The hex bolt heads will be on the

same side as the logo on the tuner shelf bracket.

2. Loosely install the two 4” long U-bolts, two V-saddle clamps with the 5/16”-20 Hex Nuts, 5/16”

Flat Washers, 5/16” Split Lock Washers and 5/16” External Tooth Washers as shown on the

tuner shelf bracket.

- 4 -

3. With the U-bolts loose, you can slip

the assembly onto the lower base

tube. <Hint: If you tilt the base, it

makes it easy to do this part of the

installation.>. Position the top U-

bolt 4-1/2” below the top of the

base tube as shown. (Refer to Page

40 for photos showing the

positioning of the clamps and

tuner). Once positioned correctly,

tighten all of the hardware holding

the tuner shelf assembly to the

lower base tube. Do not over tighten

the U-Bolt Hex Nuts which can

break or bend the aluminum saddle

clamp. Evenly tighten each side of the U-bolt until the split lock washer is seated properly.

4. Place one 5/16” External Star Washer on each of the four bolts that are installed in the tuner shelf

bracket and then place the MFJ-998RT Tuner on the bolts as shown. Position the tuner so it is

straight and the large hole on the tuner metal bracket is close to the antenna (this is where the

feedline wire will pass through). Use one 1/4”-20 Acorn Nut on each of the bolts to secure the

MFJ-998RT tuner in place.

- 5 -

5. When the upper antenna parts are mounted to the base assembly (see previous installation

instructions), install the Studded Band Clamp on the first element just above the black insulator

with the stud facing the side nearest the tuner connections. Install the 10” long tuner wire from

the studded band clamp using the #10 hardware. The other end of the 10” wire is connected to

the tuner output wing nut connection as shown.

The feedline coaxial cable connects to the Antenna Tuner to the Bias-T in the radio room.

Two views showing the

MFJ-998RT installed on the

DXE-MBVE-5A antenna

- 6 -

Bias Tee Information

The MFJ-4117 Bias Tee is included with the MFJ Remote Tuner. Since the

coaxial cable is supplying the DC voltage to the remote tuner (injected in the

coaxial cable by the Bias Tee), the coaxial cable used must have a good DC

path. Lightning protectors that block DC cannot be used.

Follow the instructions provided by MFJ for both the Tuner and the Bias

Tee.

Make certain the coaxial cables are properly connected to the Bias "T" as shown. Ensure the

ON/OFF switch on the Bias "T" is turned ON when using the system.

NOTE: Review the MFJ Remote IntelliTuner™ manual for a detailed

explanation of the Remote IntelliTuner™ and the Bias Tee operation.

Installing the Bias Tee incorrectly may cause damage to your radio.

- 7 -

Technical Support

If you have questions about this product, or if you experience difficulties during the installation,

contact DX Engineering at (330) 572-3200. You can also e-mail us at:

[email protected]

For best service, please take a few minutes to review this manual before you call.

Manual Updates

Every effort is made to supply the latest manual revision with each product. Occasionally a manual

will be updated between the time your DX Engineering product is shipped and when you receive it.

Please check the DX Engineering web site (www.dxengineering.com) for the latest revision manual.

Warranty

All products manufactured by DX Engineering are warranted to be free from defects in material and workmanship for a

period of one (1) year from date of shipment. DX Engineering’s sole obligation under these warranties shall be to issue

credit, repair or replace any item or part thereof which is proved to be other than as warranted; no allowance shall be

made for any labor charges of Buyer for replacement of parts, adjustment or repairs, or any other work, unless such

charges are authorized in advance by DX Engineering. If DX Engineering’s products are claimed to be defective in

material or workmanship, DX Engineering shall, upon prompt notice thereof, issue shipping instructions for return to

DX Engineering (transportation-charges prepaid by Buyer). Every such claim for breach of these warranties shall be

deemed to be waived by Buyer unless made in writing. The above warranties shall not extend to any products or parts

thereof which have been subjected to any misuse or neglect, damaged by accident, rendered defective by reason of

improper installation, damaged from severe weather including floods, or abnormal environmental conditions such as

prolonged exposure to corrosives or power surges, or by the performance of repairs or alterations outside of our plant,

and shall not apply to any goods or parts thereof furnished by Buyer or acquired from others at Buyer’s specifications.

In addition, DX Engineering’s warranties do not extend to other equipment and parts manufactured by others except to

the extent of the original manufacturer’s warranty to DX Engineering. The obligations under the foregoing warranties

are limited to the precise terms thereof. These warranties provide exclusive remedies, expressly in lieu of all other

remedies including claims for special or consequential damages. SELLER NEITHER MAKES NOR ASSUMES ANY

OTHER WARRANTY WHATSOEVER, WHETHER EXPRESS, STATUTORY, OR IMPLIED, INCLUDING

WARRANTIES OF MERCHANTABILITY AND FITNESS, AND NO PERSON IS AUTHORIZED TO ASSUME

FOR DX ENGINEERING ANY OBLIGATION OR LIABILITY NOT STRICTLY IN ACCORDANCE WITH THE

FOREGOING.

©DX Engineering 2017

DX Engineering®, DXE®, DX Engineering, Inc.®, Hot Rodz®, Maxi-Core®, DX Engineering THUNDERBOLT®, DX

Engineering Yagi Mechanical®, EZ-BUILD®, TELREX®, Gorilla Grip®Stainless Steel Boom Clamps, Butternut®,

SkyHawk™, SkyLark™, SecureMount™, OMNI-TILT™, RF-PRO-1B®, AFHD-4®are trademarks of PDS Electronics,

Inc. No license to use or reproduce any of these trademarks or other trademarks is given or implied. All other brands

and product names are the trademarks of their respective owners.

Specifications subject to change without notice.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali DX Engineering Antenna

DX Engineering

DX Engineering DXE-MBVE-1UGBRT3 Manuale utente

DX Engineering

DX Engineering DXE-ARAH3-1P Manuale utente

DX Engineering

DX Engineering DXE-160VA-1 Manuale utente

DX Engineering

DX Engineering DXE-RDPK-160 Manuale utente

DX Engineering

DX Engineering 4-BTV Manuale di istruzioni

DX Engineering

DX Engineering OMNI-TILT DXE-OMNITILT-1 Manuale utente

DX Engineering

DX Engineering DXE-VGMT-3CG Manuale utente

DX Engineering

DX Engineering 4-BTV Manuale utente

DX Engineering

DX Engineering HEXXAGONAL BEAM Mark 2 Manuale utente

DX Engineering

DX Engineering DXE-HEXX-BAL-KIT Manuale utente

DX Engineering

DX Engineering DXE-30VE-1 Manuale utente

DX Engineering

DX Engineering DXE-PS-2B-P Manuale utente

DX Engineering

DX Engineering ARAH3-1P Manuale utente

DX Engineering

DX Engineering Hot Rodz DXE-HR-2P Manuale utente

DX Engineering

DX Engineering DXE-SWA-070 Manuale utente

DX Engineering

DX Engineering DXE-NVIS-8040 Manuale utente

DX Engineering

DX Engineering DXE-RRMX2X8 Manuale utente

DX Engineering

DX Engineering DXE-40VE-1 Manuale utente

DX Engineering

DX Engineering DXE-7580FS-VA Manuale utente

DX Engineering

DX Engineering DXE-MBVE-3 Manuale utente

DX Engineering

DX Engineering MFJ-1734 Manuale utente

DX Engineering

DX Engineering DXE-8040-30AOK Manuale utente

DX Engineering

DX Engineering DXE-MBVE-5A Manuale utente

DX Engineering

DX Engineering DXE-AOK-80M Manuale utente

Manuali Antenna popolari di altre marche

Alfa Network

Alfa Network APA-L01 Manuale utente

Naval

Naval PR-422CA Manuale utente

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Manuale utente

TERK Technologies

TERK Technologies TV44 Manuale utente

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Manuale utente

HP J8999A Manuale utente

MobilSat

MobilSat MSP-S Manuale utente

Steren

Steren ANT-UHF 13 Manuale utente

Novatel

Novatel 600-G Manuale operativo

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Manuale utente

TRENDnet

TRENDnet TEW-AO12O Manuale utente

Radio Shack

Radio Shack 15-1837 Manuale utente

CommScope

CommScope CMAX-OMFX-43M-I53 Manuale utente

Ramsey Electronics

Ramsey Electronics DAP25 Manuale utente

COBHAM

COBHAM SAILOR 800 VSAT Manuale per l'uso e la cura

Trango Systems

Trango Systems AD900-9 Manuale utente

Steren

Steren ANT-100 Manuale utente

Proxim

Proxim 5054-PA-23 Manuale utente