Dymo LabelWriter SE450 Label Printer Manuale utente

Quick Start Guide

LabelWriter®

Professional Label Printer for Serial and USB Connections

SE450

No part of this document or the software may be reproduced or transmitted in any form or by any means, or translated into

another language without the prior written consent of Sanford, L.P.

Trademarks

DYMO, LabelWriter, and DYMO Label are trademarks or registered trademarks of Sanford, L.P. All other trademarks are the

property of their respective holders.

This Quick Start Guide gives instructions for connecting the printer, installing the software, and

loading the labels. For complete information about programming and using the LabelWriter

SE450 printer, refer to the LabelWriter SE450 Technical Reference Guide available on the

Developers Program page of the DYMO Web site (www.dymo.com).

The LabelWriter SE450 label printer is primarily intended for applications limited to sending simple

ASCII print data and Escape commands for printing from computers or devices using the serial or

USB connections. In addition, printer drivers are included for printing from a Mac, Windows, or

Linux system.

The software CD included with the printer includes the printer drivers for Windows, Mac, and Linux,

and the full DYMO Label v.8 software installer. However, when used primarily as an ASCII printer,

the drivers may not be required by your system.

Unpacking the Printer

Make sure you have all the items shown in Figure 1. (Labels included in the package may vary.)

Figure 1

Starter roll of labels

Quick Start Guide

Power adapter

Power cord

LabelWriter printer

USB cable

CD-ROM

Cleaning card

Serial cable

Quick Start Guide

Become familiar with the printer’s major components. See Figure 2.

LabelWriter Printer Features

Your LabelWriter printer is a direct thermal printer and does not use ink or toner. Instead, the printer

uses heat from a thermal print head to print on specially treated labels. Labels are the only supplies

you will ever need to buy.

The form-feed button on the front of the printer advances a single label.

The status light visually shows the current state of the printer:

•Solid blue - USB cable is connected and printer is ready to print.

•Solid green - Serial cable is connected and printer is ready to print.

•Dimmed blue or green - printer is in power saving mode.

•Flashing red - Labels are not loaded properly or the label roll is empty.

•Flashing green - Printer is in configuration mode. Refer to the Technical Reference Guide.

USB 10101 24VDC

S/N 00000-0000000

Top cover

Label spool

Label release

Label feed path

and tear bar

Label roll

Form-feed button

and status light

DC power

connector

Serial number

Cable

channel

Serial

connector

USB

connector

Figure 2

Installing as a Serial ASCII Printer (Windows)

1Plug the end of the serial cable with the RJ11 connector

into the serial port on the bottom of the printer. See

Figure 3.

2Connect the 9-pin serial connector to an available serial

port on your computer or device, as appropriate.

3Plug the power cord into the power adapter.

4Plug the power adapter into the power connector on the

bottom of the printer.

5Insert the cables through the cable channel.

6When all the cables are connected, plug the power cord

into an electrical outlet.

7Configure the printer port with the appropriate settings.

The printer default settings are:

Baud Rate: 9600

Data Bits: 8

Stop Bits: 1

Parity: None

Follow the instructions in "Loading Labels" on page 6 to correctly load labels onto the spool and

insert the spool into the printer.

USB 10101 24VDC

Figure 3

10101 24VDC

Installing as a USB Connected Printer

The LabelWriter SE450 printer includes DYMO Label v.8 label printing software. You can choose to

install the DYMO Label v.8 software or only the LabelWriter SE450 printer drivers depending on how

you plan to use the printer.

Printer drivers for Windows and Mac are installed from the CD. For those familiar with Linux or CUPS,

the CUPS SDK, including the printer drivers, is included on the Software CD.

Installing the Software

Do not connect the printer to your computer until after the software installation is complete.

To install the printer drivers only (Windows only)

1Insert the software CD that came with your printer into the CD-ROM/DVD drive. After a few

seconds, the installation screen appears.

2Click Install and follow the instructions on the next few screens.

3On the Installation Type screen, choose Custom installation.

4Clear the DYMO Label check box so that only the Printer Drivers check box is selected.

5Click Next and follow the instructions.

6When prompted, connect the printer to your computer. See "Connecting the Printer" on page 5.

To install DYMO Label software

Windows Depending on your system configuration, the software installation could take some

time while the required Microsoft .NET™software is installed.

1Close all open Microsoft Office applications.

2Insert the software CD that came with your printer into the CD-ROM/DVD drive.

3Do one of the following:

•For Windows: Click Install and follow the instructions in the installer.

•For Mac OS: Double-click the Installer icon and follow the instructions.

4When prompted, connect the printer to your computer. See “Connecting the Printer”.

Mac OS If the printer is not in the printer list when the installation is complete, refer to the

ReadMe file for instructions on how to add the printer.

Connecting the Printer

1Plug the USB cable into the USB port on the bottom

of the printer.

2Connect the other end of the USB cable into an

available USB port on your computer or other

device, as appropriate.

3Plug the power cord into the power adapter. See

Figure 4.

4Plug the power adapter into the power connector on

the bottom of the printer.

5Insert the power and USB cables through the cable channel.

6When all the cables are connected, plug the power cord into an electrical outlet.

Follow the instructions in "Loading Labels" on page 6 for the correct way to load labels onto the

spool and insert into the printer.

USB 10101 24VDC

USB

Figure 4

24VDC

Loading Labels

Important!

In order for the labels to feed properly during printing, the labels must be loaded with the left edge of

the label inserted against the left edge of the label feed slot. See Figure 8.

To load a label roll

1Press the form-feed button to eject the labels that

protected the printer during shipment.

2Open the top cover and remove any packing material

inside the label compartment.

3Remove the label spool from inside the top cover and

pull the spool guide from the spindle.

4Hold the spool spindle in your left hand and place the

label roll on the spindle so that the labels feed from

underneath and the left edge of the label roll is firmly against the side of the spool. See

Figure 5.

5Slide the spool guide onto the right side of the spool and press the

guide tightly against the side of the label roll, leaving no gap

between the roll and the spool. See Figure 6.

NOTE To ensure proper feeding of labels during printing, the label roll

must fit snugly against both sides of the label spool, with no gaps.

Figure 5

Spool

guide

Spool

spindle

Figure 6

6Insert the label spool into the slot in the printer cover with

the labels extending from underneath the roll. See

Figure 7.

7Align the left edge of the label with the left edge of the

label feed slot and insert the label into the slot.

The printer automatically feeds the label, stopping at the

beginning of the first label.

If the printer does not feed the labels, make sure the

first label is fully inserted and then press the form-feed

button on the front of the printer.

If the first label on the roll is not a full label, press the

form-feed button to eject the partial label.

8Carefully lower the top cover.

Figure 7

Align labels

against left edge

More Information

For more information about programming and using the LabelWriter SE450 printer, refer to the

following resources:

For customer support, visit the support section of the DYMO Web site (www.dymo.com).

LabelWriter Printer User Guide Complete information for using and caring for

LabelWriter 450 series label printers, including the

LabelWriter SE450 printer.

This user guide is located on the software CD or it can be

viewed from the Help menu in DYMO Label v.8 software.

LabelWriter SE450 Technical Reference Guide Complete information for integrating label printing into

custom applications on Linux, DOS or embedded

platforms.

The Technical Reference Guide can be accessed from

the Developers Program page of the DYMO Web site

under LabelWriter SE450 SDK. (www.dymo.com)

Sample Code Programming examples for the LabelWriter SE450 ASCII

commands are located on the software CD in the

Samples folder.

CUPS SDK CUPS Software Developer’s Kit, including the

LabelWriter SE450 printer drivers, is located on the

software CD.

Altri manuali per LabelWriter SE450 Label Printer

Indice

Altri manuali Dymo Etichettatrice

Dymo

Dymo LabelPOINT 100 Manuale utente

Dymo

Dymo Omega Manuale utente

Dymo

Dymo LabelManager 160 Manuale utente

Dymo

Dymo LabelManager 280 Manuale utente

Dymo

Dymo LabelManager Wireless PnP Manuale utente

Dymo

Dymo Rhino 3000 Industrial Label Printer Manuale utente

Dymo

Dymo LabelManager Wireless PnP Manuale di istruzioni

Dymo

Dymo LabelWriter Twin Turbo Manuale utente

Dymo

Dymo LabelManager 300 Manuale utente

Dymo

Dymo LabelWriter 450 Duo Label Printer Manuale utente

Dymo

Dymo Junior Manuale utente

Dymo

Dymo LabelWriter 310 Manuale del proprietario

Dymo

Dymo LabelWriter DUO Manuale utente

Dymo

Dymo RHINO 6000 Manuale utente

Dymo

Dymo LabelMANAGER 150 Manuale utente

Dymo

Dymo LabelManager Wireless PnP Manuale utente

Dymo

Dymo LabelWriter 400 Manuale utente

Dymo

Dymo Rhino 3000 Industrial Label Printer Manuale utente

Dymo

Dymo LabelManager 210D Manuale utente

Dymo

Dymo LabelManager 210D Manuale utente

Dymo

Dymo LabelWriter 4XL Label Printer Manuale utente

Dymo

Dymo PL100 Manuale utente

Dymo

Dymo LetraTAG XM Manuale utente

Dymo

Dymo LabelWriter DUO Manuale utente

Manuali Etichettatrice popolari di altre marche

Brother

Brother P-Touch 2420PC Manuale utente

newell

newell Dymo LabelManager 210D Manuale utente

Brother

Brother TD-4000 Manuale utente

U-Line

U-Line BROTHER H-8754 Manuale utente

Tharo Systems

Tharo Systems H-435+ Manuale utente

Brother

Brother E300 Manuale utente

Godex

Godex RT700 SERIES Manuale utente

ID Technology

ID Technology 252 Manuale utente

Labelmate

Labelmate MC-11 Manuale utente

CAB

CAB XD4M/300 Manuale utente

Avery Dennison

Avery Dennison Pathfinder 6057 Manuale di servizio

Brother

Brother P-touch PT-9700PC Manuale utente

TSC

TSC PEX1000 Series Manuale utente

Adkins

Adkins Label Master Manuale utente

Epson

Epson LabelWorks LW-400 Manuale utente

Primera

Primera 510212 Manuale utente

Brady

Brady BradyPrinter S3100 Manuale utente

DuraLabel

DuraLabel LabPRO Manuale utente